Adastra RMS605 Bruksanvisning

Läs nedan 📖 manual på svenska för Adastra RMS605 (4 sidor) i kategorin mottagare. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
RMS605
1U 5-ZONE MIXER- PLIFIER 5 x 60W AM
Item ref: 2 953.15 UK
User Manual
Version 1 1.
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
953.152 User Manual UK
Introduction
Thank you for choosing an Adastra RMS605 5-zone mixer-amp as part of your sound system.
This 5-zone 100V power amplifier has the advantage of selectable obal or individual inputs and a paging microphone input. gl
Please read this manual to gain the best results from your product and avoid damage through misuse.
SAFETY SYMBOL AND MESSAGE CONVENTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this
unit
This symbol indicates that there are important operating and maintenance instructions in the
literature accompanying this unit.
SAFETY NOTICE
1. Prior to use, read through this manual
2. Keep the manual in good condition
3. Pay attention to safety warnings
4. Observe all operating requirements
5. Do not use the device near water or wet areas
6. For cleaning, only use a lint-free, dry cloth
7. Install according to the specifications
8. Place away from heat sources or heating appliances
9. Use mains lead provided and avoid damage to cable or connectors
10. Unplug power from mains during stormy weather or if unused for long periods
11. In case of malfunction, water ingress or other damage, consult qualified service personnel
12. Do not place in damp areas or near liquids or moisture. Do not spill liquids on the housing
13. Please pay attention to warning symbols during transit and placement
14. Terminals marked with the symbol are HAZARDOUS LIVE and should only be connected by qualified personnel
15. Ensure that the apparatus is connected to a mains socket with a protective EARTH connection
16. Ensure correct operation of the mains switch
Warning
To prevent the risk of fire or electric shock, do not expose any components to rain or moisture.
If liquids are spilled on the casing, stop using immediately, allow unit to dry out and have checked by qualified personnel before
further use.
Avoid impact, extreme pressure or heavy vibration to the case
No user serviceable parts inside Do not open the case refer all servicing to qualified service personnel. – –
Safety
Check for correct mains voltage and condition of IEC lead before connecting to power outlet
Placement
This unit can be used free-standing or fixed into a 19” rack
Ensure adequate support and access to controls and connectors when rack-mounting
Cleaning
Use a soft cloth with a neutral detergent to clean the housing as required
Do not use strong solvents for cleaning the unit
953.152 User Manual UK
Front panel
Rear panel
Connection
Ensure the wer ( ) is switched off until all input and output connections are in place. Po 11
Turn all output rotary level controls (9 fully down (anti-clockwise) to avoid loud noises when switching on. )
Set the BASS and TREBLE Tone controls (1, 2, 4, 5 to the vertical position (zero) )
Loudspeakers should be connected to the RMS605 via screw terminals on one of 2 removable modular connectors.
If the speaker(s) being connected is not 100V type, use the terminal block marked 4 for this channel (14). “ Ω”
Connect + and wires to each speaker as indicated, ensuring that there is no chance of strands shorting across terminals.
Important: Ensure that the load is no lower than 4 for each output. This can be Ω …
1 x 4 1 x 16 Ω speaker Ω speaker
1 x 8 2 x 16 speakers wired in parallel (8 ) Ω speakers Ω
2 x 8 (4 ) 3 x 16 speakers wired in parallel (5.3 ) Ω speakers wired in parallel Ω Ω
4 x 16 speakers wired in parallel (4 ) Ω Ω
Ensure that the connected speakers can handle W from each output. 60
If the speaker(s) being connected to an output channel
are 100V type, use the terminal block marked for 100V
this output channel. When connecting multiple 100V
speakers to this output, connect all speakers in parallel
and ensure that the total load is below 54W.
The wattage of each speaker can sometimes be
adjusted via tappings on the speaker (check the
speaker s documentation if unsure)
DO NOT co ect to both 4 and 100V terminals for any individual output channel nn Ω
DO NOT mix 4 and 100V speakers on any single output. Ω
THERE SHOULD BE NO CONNECTION MADE VERTICALLY ABOVE OR BELOW AN OTHER Y
1.
BASS EQ Paging Mic input
7.
Power on indicator
2.
TREBLE Paging Mic input EQ
8.
GAIN control Paging Mic input
3.
Signal indicator Paging Mic input
9.
LEVEL control Output channels
4.
BASS EQ Output channels
10.
Status indicators Output channels
5.
TREBLE Output channels EQ
11.
Power on/off switch
6.
AUX/Individual channel input switch
12.
IEC mains inlet and fuse holder
17.
Paging mic VOX sensitivity control
13.
100V speaker output terminals
18.
Paging mic balanced XLR input
14.
4 speaker output terminals
19.
24V emergency mute termina ls
15.
Line level individual channel RCA inputs
20.
Line level individual channel terminal inputs
16.
Line level AUX RCA inputs
21.
Phantom power and Vox DIP switches

Produktspecifikationer

Varumärke: Adastra
Kategori: mottagare
Modell: RMS605

Behöver du hjälp?

Om du behöver hjälp med Adastra RMS605 ställ en fråga nedan och andra användare kommer att svara dig




mottagare Adastra Manualer

mottagare Manualer

Nyaste mottagare Manualer