Alecto DVM2043C Bruksanvisning
Läs nedan 📖 manual på svenska för Alecto DVM2043C (4 sidor) i kategorin Babyvakt. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
2 Before use
DVM2043C User’s manual
(For use with DVM2043)
3 Positioning the baby monitor
1 Connect and power on the baby unit
Quick start guide
What’s in the box
Pair a new baby unit
Each newly purchased baby unit ( ) must be paired to your system ( ).DVM2043C DVM2043
NOTESNOTE
• You can pair an additional baby unit to your parent unit. New baby unit must be paired to the
parent unit before use.
• Make sure you power on the parent unit before pairing.
1. Turn on your parent unit and baby unit.
2. Press when the parent unit is idle.
3. Go to > , select 2.
If you have more baby units: select , then select 2, 3 or 4.
4. Press and hold the PAIR button for 3 seconds until you hear a “beep”.
5. When the baby unit is successfully paired with your parent unit, the parent unit
displays and the live video.
Overview - Baby unit
Declaration of conformity
Hereby, Commaxx declares that the radio equip-
ment type Alecto DVM2043C is in compliance with
directive 2014/53/EU. The full text of the EU dec-
laration of conformity is available at the following
Internet address: https://commaxx-certificates.com/
doc/DVM2043C_doc
Use of this equipment is allowed in all countries
of the EU. In France, Italy, Russia and Ukraine, only
indoor use is allowed.
Information power adaptor baby unit:
Manufacturers name and address:
Vtech Telecommunications LTD, 23/F.,
Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road,
Tai Po, Hong Kong.
Model Identifier: VT05EEU05100
Input voltage: 100 - 240V~
Input AC frequency: 50/60 Hz
Output voltage: 5.0V DC
Output current: 1A
Output power: 5.0 W
Average active efficiency: 74.0 %
Efficiency at low 10% load: -
No load power consumption: 0.07 W
ATTENTION
Before you start using the product, please remove any
protective foil from the baby unit.
Specications
Range:
up to 50 meters indoors
up to 300 meters outdoors
Baby unit power:
5V DC 1A power adaptor (incl.)
Model: VT05EEU05100
Frequency: 2405-2475 MHz
Modulation: FSK
RF-power: <20 dBm
Important safety instructions
The applied nameplate is located at the bottom of the baby
unit’s base.
1. CAUTION: Do not install the baby unit at a height above
2 metres.
2. Use and store the product at a temperature between
0oC and 40oC.
x 2
x 2
1Light sensor
2Camera
3Infrared LEDs
4Night light
5Microphone
6Speaker
7POWER LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the link to the parent unit
has lost.
8 Night light on/off key
9Antena
10 Temperature sensor
11 Power jack
12 PAIR key
• Press and hold for 3 seconds to enter
paring mode.
13 Slots for wall mounting
1
2
3
4
5
7
8
9
10
6
11
12
13
Kabel mi nimaa l 1 meter rwij der d ve
houden van b aby.
Garder un e distan ce mini mal d’ un m ètr e
du bébé.
Das Kabel i st mi ndesten s 1 Mete von r,
dem Ba , en t t zu hal ten .by fern
Keep ca e at l east 1 m from babbl away y.
Man ten ga el ca e a l men os 1 m etr o de bl
distanci a del bebé
V1.1
Connect the power adaptor to the baby unit and a power supply to power on the unit.
Disconnect the baby unit from the power supply to power off.
NOTESNOTE
• Use only the power adaptor supplied with this product.
• Make sure the the baby unit are not connected to an electronically/timer controlled electric power outlet.
• Connect the power adaptor in a vertical or floor mount position only. The adaptor prongs are not
designed to hold the weight of the baby unit. Otherwise, the adaptor may not properly connect to the
outlets.
• Make sure the the baby unit and the power adaptor cords are out of reach of children.
Caution
• The manufacturing preset volume
of your parent unit is level , and the 4
maximum volume is level 7. If you
experience feedback noise from your
baby monitor while positioning:
- Make sure your baby unit and parent
unit are more than 1 metre apart, OR
- Lower the volume of your parent unit.
1
Commaxx B.V., Wiebachstraat 37,
6466 NG Kerkrade, The Netherlands
support.alectobaby.nl
- DVM2043C
Video baby monitor - Baby unit
V 1 . 0
Mount the baby unit on dry wall (optional) Tips and remarks
INTERFERENCE-FREE:
This baby display monitor is digitally coded. This means you will never receive signals from other devices, nor can the signal from your baby unit(s) be received by e.g. your neighbors.
In case the baby unit(s) or parent unit is placed in or in the close vicinity of electromagnetic fields, the signal (images or sound) can be slightly affected. If this happens, try a different
location for the baby unit(s) or parent unit or move, if possible, the source of the interference.
EAVESDROPPING/WIRETAPPING:
Eavesdropping/wiretapping of the signals from this baby video monitor is nearly impossible. Not only must one be within range of the baby video monitor, one also needs some very
costly equipment.
MAINTENANCE:
Only clean the baby monitor with a moist cloth; never use chemical cleaners. Before any cleaning, you must disconnect the adaptors.
RANGE:
The baby display monitor has a range of up to 300 meters in an open field and up to 50 meters indoors; this range depends on local circumstances.
DELAY IN IMAGES AND SOUND:
Te baby unit transmits the images and sound to the parent unit in digital blocks. The parent unit converts these signals back to a recognizable image
and a comprehensible sound. Therefore, there is a small delay between the moment of movement and making sounds and the display and sounds of the parent unit.
Besides that, the sounds and images on the parent unit are not exactly simultaneous.
Commaxx BV
Wiebachstraat 37
6466 NG Kerkrade
The Netherlands
www.alectobaby.com
1. Place the wall mount bracket on a
wall and then use a pencil to mark
two holes in parallel. Remove the
wall mount bracket and drill two
holes in the wall (5.5mm drill bit).
Notes
• Check for reception strength and
camera angle before drilling the holes.
• The types of screws and wall plugs you
need depend on the composition of
the wall. You may need to purchase
the screws and wall plugs separately to
mount your camera units.
2. If you drill the holes into a stud, go
to step 3.
• If you drill the holes into an
object other than a stud, insert
the wall plugs into the holes.
Tap gently on the ends with a
hammer until the wall plugs are
flush with the wall.
3. Align the wall mount bracket and screws with
the holes in the wall as shown. Tighten the screw
in the middle hole first, so that the wall mount
bracket position is fixed. You can tighten the
other screw in the top hole.
3. Insert the screws into the holes and
tighten the screws until only 6.5mm of
the screws are exposed.
4. Place the camera unit on the
wall mount bracket, and then
slide it forward until it locks
into place. Align the holes on
the wall mount bracket with
the screws on the wall, and
slide the wall mount bracket
down until it locks into place.
5. You can maximise your camera unit viewing angle by tilting the wall mount bracket.
Hold the camera unit, and then rotate the knob in an anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the
joint and secure the angle.
OR
4. Place the camera unit on the wall mount
bracket, and then slide it forward until
it locks into place. Connect the power
adaptor to the camera unit and a power
supply.
21
Produktspecifikationer
| Varumärke: | Alecto |
| Kategori: | Babyvakt |
| Modell: | DVM2043C |
Behöver du hjälp?
Om du behöver hjälp med Alecto DVM2043C ställ en fråga nedan och andra användare kommer att svara dig
Babyvakt Alecto Manualer
21 Oktober 2024
21 Oktober 2024
18 Oktober 2024
2 Oktober 2024
29 September 2024
26 Augusti 2024
23 Augusti 2024
19 Augusti 2024
19 Augusti 2024
17 Augusti 2024
Babyvakt Manualer
- Babyvakt IKEA
- Babyvakt Brondi
- Babyvakt Philips
- Babyvakt Grundig
- Babyvakt Motorola
- Babyvakt Topcom
- Babyvakt VTech
- Babyvakt Tefal
- Babyvakt Alcatel
- Babyvakt Angelcare
- Babyvakt Ansmann
- Babyvakt Amplicomms
- Babyvakt Silvercrest
- Babyvakt SereneLife
- Babyvakt Beurer
- Babyvakt Hyundai
- Babyvakt Chicco
- Babyvakt Jane
- Babyvakt Overmax
- Babyvakt Concept
- Babyvakt Medisana
- Babyvakt Ezviz
- Babyvakt Elro
- Babyvakt EMOS
- Babyvakt Denver
- Babyvakt Hama
- Babyvakt Cresta
- Babyvakt Babymoov
- Babyvakt Eufy
- Babyvakt Sanitas
- Babyvakt Audioline
- Babyvakt Uniden
- Babyvakt BT
- Babyvakt Goclever
- Babyvakt Graco
- Babyvakt BabyOno
- Babyvakt Oricom
- Babyvakt Safety 1st
- Babyvakt Switel
- Babyvakt Duux
- Babyvakt Nova
- Babyvakt Luvion
- Babyvakt Konig
- Babyvakt Reer
- Babyvakt Tesla
- Babyvakt Foscam
- Babyvakt D-Link
- Babyvakt Lionelo
- Babyvakt Lorex
- Babyvakt Basetech
- Babyvakt HQ
- Babyvakt Chipolino
- Babyvakt Beaba
- Babyvakt Bebetel
- Babyvakt Truelife
- Babyvakt NUK
- Babyvakt Tomy
- Babyvakt Babysense
- Babyvakt Modern-Electronics
- Babyvakt Duronic
- Babyvakt Hartig Helling
- Babyvakt Levana
- Babyvakt IBaby
- Babyvakt Kogan
- Babyvakt Mobi
- Babyvakt Neonate
- Babyvakt Pabobo
- Babyvakt Neno
- Babyvakt Philips-Avent
- Babyvakt Heimvision
- Babyvakt BabySafe
- Babyvakt Chillax Baby
- Babyvakt Hubble Connected
- Babyvakt Peekyboo
Nyaste Babyvakt Manualer
27 Oktober 2024
23 Oktober 2024
22 Oktober 2024
21 Oktober 2024
20 Oktober 2024
20 Oktober 2024
19 Oktober 2024
7 Oktober 2024
3 Oktober 2024
3 Oktober 2024