American International MITK890 Bruksanvisning

Läs nedan 📖 manual på svenska för American International MITK890 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/6
MITK890 Mounting Kit
Mitsubishi
1995-05 ECLIPSE
2000-04 MONTERO SPORT
2003-06 OUTLANDER
Eagle
1995-98 TALON
VEHICLE APPLICATIONS
©2013 AMERICAN INTERNATIONAL INDUSTRIES, INC. TECH Ver. 12/13 PRINT Ver. 12/13
2
1995-98 EAGLE TALON
1995-99 MITSUBISHI ECLIPSE
1. Carefully unsnap the trim bezel from around the radio starting at the top,
and remove trim bezel.
2. Remove the (2) Phillips screws from the radio opening securing the top of the
lower console to the sub-dash.
3. Gently lift up and remove the ashtray/drink holder from the center console.
4. Remove the (2) Phillips screws under ashtray / drink holder location.
5. Remove the (2) Phillips screws (1) from each rear side of the center console.
6. Carefully lift center console upward, disconnect the light from inside the ashtray/drink
holder location.
7. Disconnect the connections on the lighter receptacle, and remove the center console.
8. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
9. Carefully pull radio forward, disconnect wire harness and antenna lead and
remove the radio.
*SEE note below
see back page
for kit assembly
instructions
EXPLODED VIEW OF
UPPER CONSOLE
MOUNTING HOLE LOCATIONS
SPEED CLIP
*NOTE: MUST REMOVE SPEED CLIPS
FROM SUB-DASH. CAREFULLY FILE
1/8” FROM LEFT AND RIGHT INSIDE
EDGE OF CONSOLE MOUNTING
LOCATIONS (SEE SHADED AREAS
ABOVE). RE-INSERT SPEED CLIPS
FROM BOTTOM EDGE FACING UP.
DASH DISASSEMBLY & RADIO REMOVAL INSTRUCTIONS
SUB-DASH PREPARATION
SPEED CLIP
3
1995-98 EAGLE TALON
1995-99 MITSUBISHI ECLIPSE
FOR DIN AND ISO MOUNT
APPLICATIONS INSERT SPACERS INTO
BRACKETS ON BOTH SIDES ONLY
WHEN ISO MOUNTING RADIO
*REMOVE shaded areas
only on both sides of
BRACKETS FOR
95-99 ECLIPSE/TALON
APPLICATIONS
*note: remove only outer half of upper mounting tab
on ISO bracket part Imb-890 R
remove only the 3 parallel side mounting tabs on part
Imb-890 l (See figure b)
Do not remove
this piece
Fig. B
KIT ASSEMBLY
DIN MOUNT INSTRUCTIONS
1. Insert DIN sleeve from your new radio into the upper section of the installation kit.
(This DIN sleeve comes with all new radios and slides off the back of the radio)
2. Depress the tabs from inside the sleeves opening upward, outward, and downward
to secure sleeve to the installation kit.
3. Install radio into sleeve and lock into place.
4. Support rear of radio with back strap.
Optional use Trim Ring (ITR-890) may be used on some radios if desired.
Due to the movement of some faces on some radios our ISO Trim Ring may not be able
to be used.
Your new radio must have a trim ring around the face of the radio that is designed to be
easily removed. Consult your radio ownerʼs manual.
DIN Sleeve
ITR-890 Trim Ring
(Optional Use)
ITR-890 Trim Ring
(Optional Use)

Produktspecifikationer

Varumärke: American International
Kategori: Inte kategoriserad
Modell: MITK890

Behöver du hjälp?

Om du behöver hjälp med American International MITK890 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad American International Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer