AMX DX-TX Bruksanvisning

AMX Inte kategoriserad DX-TX

Läs nedan 📖 manual på svenska för AMX DX-TX (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

QUICK START GUIDE

DXLink™ Twisted Pair Transmitter/Receiver

Overview

The DXLink Multi-Format TX and HDMI RX Modules transmit HDMI, audio, and control

over twisted pair cable. The TX also has an analog video input. DXLink Modules can be

set up in one of three ways:

• Endpoint Mode (Switcher) – connect one or more to a switcher with an integrated

Master.

• Endpoint Mode (Standalone) – connect TX/RX pair directly to each other with one

connected to a NetLinx Central Controller via LAN or directly to Controller.

• Extender Mode (Standalone) – connect TX/RX pair directly to each other.

These Modules support InstaGate Pro® and SmartScale® Technology.

The Hardware Reference Manual – DXLink Twisted Pair Transmitters/Receiver contains

complete documentation (including full specifications and supported input and output

resolutions); for details, see www.amx.com .

System Setup

The Multi-Format TX and the RX work with a switcher that supports DXLink Technology

for transmission of HDMI (or with a Central Controller) or as a stand-alone pair. The

Transmitter receives an HDMI signal (or analog video on a Multi-Format TX) and

embedded audio from the source. Both the video and embedded audio are transported

over twisted pair cable to a DXLink Input Board (or connector). The signal is routed via

the DXLink Output Board (or connector) to an RX. On the Transmitter, stereo audio or

digital audio connections are provided as supplemental audio inputs. The RX also

provides a stereo audio output. Both the Transmitter and the Receiver support RS-232

for serial data transfer, USB, IR, and Ethernet.

DIP Switch Toggles – Default OFF (for Auto-setup, see next page)

Before installing the units, find the scenario you are using in the table below and set the

DIP switch toggles accordingly. Toggle #4 is reserved for future functionality.

For standalone pair upgrades, set Toggles #1-2-3 to ON and connect one unit to Master.

* Connect ICS LAN port of DXLink unit to network device (e.g., laptop, IP controlled

projector, ICSLan Device). In standalone setup, connect ICS LAN port of other DXLink

unit to network.

** In standalone setup using NetLinx control of DXLink serial/IR ports, only one of the

DXLink units should be connected to network (the unit with #1 Toggle enabled).

Mounting Options (Rack Trays and Mounting Brackets)

For details on the four versatile mounting kit options for V Style modules (rack tray, rack

tray with fill plates, surface mount, and pole mount), see www.amx.com .

IMPORTANT: When mounting under a surface, the module should be mounted upright

and lowered in the mounting bracket slots to provide an airflow gap between the surface

and the vent holes. If not using V Style brackets, be sure to leave a gap between the top of

the unit and the surface for heat to escape.

Twisted Pair Cable Pinouts and RJ-45 LEDs

The DXLink and ICS LAN 10/100 ports both use twisted pair cable. FIG. 4 shows two

pinouts that can be used for either port. FIG. 5 shows the LEDs for each port.

Attaching Signal, Transport, and Control Cables

Important Twisted Pair Cabling Requirements and Recommendations:

• DXLink cable runs require shielded category cable (STP) of Cat6 (or better).

• DXLink twisted pair cable runs for DXLink equipment shall only be run within a

common building.*

• DXLink (RJ-45) connectors must not be used for connecting to a standard

Ethernet Network. The connector is used for signal transport.

• Do not create a network (Ethernet) loop. A network loop is created when the

enclosure and one or more of its DXLink Modules are connected to a common LAN

(or a standalone pair when both endpoints connect to the same network).

• DXLink delivers 10.2 Gb/s throughput over shielded category cable. Based on this

bandwidth requirement, we recommend following industry standard practices

designed for 10 Gigabit Ethernet when designing and installing the cable

infrastructure.

• The cables should be no longer than necessary to reach the end-points. We

recommend terminating the cable to the actual distance required rather than

leaving any excess cable in a service loop.

• For complete cable specifications, see the Hardware Reference Manual – DXLink

Twisted Pair Transmitters/Receiver.

* “Common building” is defined as: Where the walls of the structure(s) are physically

connected and the structure(s) share a single ground reference.

For more details and helpful cabling information, reference the white paper titled

“Cabling for Success with DXLink” available at www.amx.com or contact your AMX

representative.

Grounding

If the system is experiencing problems with delivery of DXLink signals to/from an Enova

DGX Digital Media Switcher or Enova DVX Solution, adding a ground wire from the

TX/RX to the switcher may improve performance. Technically this type of grounding is

only required when a DXLink Transmitter or Receiver is connected to an ungrounded

device, but this added grounding measure can be used at the discretion of the installer

(for instructions, see the product manual).

IMPORTANT: If one DXLink Transmitter or Receiver is grounded, any remaining

ungrounded units that are connected to the same board on an Enova DGX Switcher must

also be grounded.

FIG. 1 DXLINK TX AND RX AS ENDPOINTS WITH COMPATIBLE DXLINK EQUIPMENT

FIG. 2 DXLINK TX AND RX AS EXTENDER SOLUTION

COMMON SCENARIOS TOGGLES

Standalone Setup 1 - 2 - 3

AV signals only (plus serial/IR passthrough) OFF - OFF - OFF

AV with Ethernet passthrough to networked device (plus serial/IR

passthrough)*

ON - OFF - OFF

AV with NetLinx control of TX/RX unit and serial/IR ports** ON - ON - ON

AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet

passthrough to network device*

ON - ON - ON

Switcher Setup (TX/RX with Enova DGX/DVX /DGX 100 Series Switcher) 1 - 2 - 3

AV signals only OFF - OFF - OFF

AV with Ethernet passthrough to networked device* ON - OFF - OFF

AV with NetLinx control of TX/RX unit and serial/IR ports OFF - OFF - ON

AV with NetLinx control of TX/RX unit and serial/IR ports, plus Ethernet

passthrough to network device*

ON - OFF - ON

DXLink Enova DGX 16

Input Boards DXLink

Output Boards

DXLink Transmitter

Destination device

Source device DXLink Receiver

Twisted pair cable

DXLink Transmitter

Source device

DXLink Receiver

Destination device

FIG. 3 DIP SWITCH TOGGLES ENABLE/DISABLE SPECIAL FUNCTIONALITY

FIG. 4 RJ-45 PINOUTS

FIG. 5 RJ-45 PORTS

Yellow LED

On - Speed status is 100 Mbps

Off- Speed status is 10 Mbps

Green LED

On - Link status is active

Off- Link status is not active

Green LED

On - Connection established

Off- Connection not established

Yellow LED

On - Authenticated HDCP

Flashing - Video active; no HDCP

Off- No Video

DXLink Port

ICS LAN 10/100 Port

registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of

their respective companies.

AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.

The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153

AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/

93-1010-300 REV: L

Last Revised: 12/15/2015

To attach signal, transport, and control cables to the Transmitter:

1. Set DIP switch toggles if necessary (for settings, see the previous page).

2. Attach HD-15 cable from source to Video In connector.

3. HDMI In – Attach an HDMI cable from the source to the HDMI In connector.*

4. DXLink connector – Attach a twisted pair cable to the DXLink output and to a

DXLink input connector on the switcher (or on the RX for a standalone pair).

5. Stereo Audio In jack (optional) – Insert analog audio cable from source.

6. Digital Audio In jack (optional) – Insert S/PDIF plug on digital audio cable from source.

7. ICS LAN10/100 port (optional) – Use to attach twisted pair cable to LAN.

* DVI cable can be used via a cable adapter; however, advanced audio support from

HDMI will not be available.

To attach signal, transport, and control cables to the Receiver:

1. Set DIP switch toggles if necessary (for settings, see previous page).

2. DXLink input connector – Attach a twisted pair cable from the DXLink output

connector on the switcher (or on a TX) to the DXLink input.

3. HDMI Out – Attach HDMI cable from this port to the destination.

4. Stereo Audio Out jack (optional) – Connect analog audio cable from port to

destination.

Applying Power

A desktop power supply is provided with each module. Power can be supplied to DXLink

Twisted Pair Modules by DXLink Power sourcing devices as follows:

• To a TX or RX module from an Enova DGX Switcher or PS-POE-AT-TC (FG423-84)

or PDXL-2 (FG1090-170).*

• To a TX module from a DVX-3156HD, DVX-3155HD, or DVX-2155HD.

• To an RX module from a DVX-2155HD, DVX-2150HD, or an SDX-501M-DX.

Power Budget: For TXs and/or RXs connected to an Enova DGX, use the Enova DGX

Configuration Tool (www.amx.com/enova) to determine power requirements of a

configuration and if any DXLink TXs or RXs should use the local power. The tool

contains instructions on how to use it.

* To use PS-POE-AT-TC or PDXL-2 as a power source, the TX requires firmware v1.2.40

(or later) and the RX v1.0.80 (or later).

NOTE: Local power takes precedence over DXLink power (via DXLink port) from switcher.

IMPORTANT: If a desktop power supply is used to power the unit, it must be the one

provided, which must not be altered in any way. AMX does not support use of any other

power supplies or PoE injectors as they may potentially damage the DXLink equipment.

To apply power to the Transmitter (or Receiver):

1. Plug the cord from the desktop power supply (provided) into the power jack on

rear of the TX (or RX) (2.1 mm DC jack for 12 V local power).

2. Plug the desktop power supply into an AC external power source. The Power LED

on the front of the TX (or RX) illuminates green, indicating a ready state.

This table shows LED states on initial power up. If not normal, check connections.

* At power up, the RX defaults to Auto. Press the Scaling button to change the mode.

DXLink Auto-setup with Enova DGX 100 Series Switchers

Auto-setup is the default for using DXLink Modules with Enova DGX 100 Series

Switchers. When all of the following conditions are met, the modules automatically go

into Auto-setup Mode and can communicate through the ICS LAN port with the

integrated Master via Telnet:

• Endpoints must be set to DHCP Mode (default) and use the NDP Master

connection mode (default).

• Endpoints must not be bound to a Master.

IMPORTANT: On the switcher, the ICS LAN port acts as a DHCP server (private LAN) and

the LAN 100/1000 port acts as a DHCP client (public LAN) with each port on a separate

network. In order to avoid a Network Loop, do not connect any device on the private

network to any branch on the public network.

IP Addressing Modes

DHCP Mode (enabled when #3 Toggle is flipped ON)

In DHCP Mode, the Module attempts to get a DHCP lease (consisting of an IP address,

gateway, and other network parameters). If the attempt fails, the Module configures

itself for a link-local address, but periodically re-tries DHCP and re-assigns the IP to a

valid DHCP grant if successful. At any time, if the Module determines that its IP address

has changed, it will disconnect and reconnect to the Master.

Static IP Mode (set with ID button or Telnet command)

With #3 Toggle set to ON, press ID for 10 seconds to assign address of 192.168.1.2 or

use a Telnet command to set unit to Static IP Mode (see the manual).

Enova DGX/DVX and DXLink IP Setup (systems without auto-setup)

The following procedure is intended to outline the steps necessary for network setup of

DXLink Twisted Pair TX and/or RX with an Enova DGX 8/16/32/64 or Enova DVX

switcher. These steps require familiarity with NetLinx Studio. If unfamiliar with NetLinx

Studio, complete instructions are included in the Hardware Reference Manual – DXLink

Twisted Pair Transmitters/Receiver.

To setup DXLink Module(s) with an Enova DGX 8/16/32/64 or Enova DVX:

1. Set the DIP switches on the DXLink Module(s).

2. Apply power to the DXLink Module(s).

3. Connect DXLink Module(s) to the Enova DGX or Enova DVX.

4. Optional – Configure a Static IP address (for each connected Module).

5. Configure the Device ID (for each connected Module).

6. Connect (Bind) the DXLink Module(s) to the Enova DGX or Enova DVX.

RS-232 Serial Data (Optional)

The 232 port label is relative to data flow. Data enters at RX label on the Transmitter, is

sent via a DXLink cable through the switcher, and leaves at TX label on Receiver. Flow is

vice versa from Receiver to Transmitter. Applies to all DXLink modules – wire RS-232

port for serial data transfer according to pinout above connectors (TXD-RXD-Ground).

IR Control (Optional)

The IR Receiver (FG-IR03) connects to the IR RX port on the Transmitter and the

IR Emitter (FG10-000-11) connects to the IR TX port on the Receiver or vice versa,

depending on the installation. The signal is sent via DXLink cable through the switcher.

When a Transmitter and Receiver are used as a standalone pair, IR control acts as a

passthrough.

USB Host and Keyboard/Mouse Ports (Rear)

If needed, the Host (USB-B) port on the TX and the K/M port (USB-A) on the RX provide

HID support for a keyboard, mouse, and HUB. For a list of supported HID devices

(keyboards and mice), see the Receiver’s product page at www.amx.com .

Program Port (Front)

This USB mini-B port on the Transmitter supports DGX Configuration Software for

programming a customer VGA EDID (for modules connected to an Enova DGX 100

Series Switcher, use the System Configuration interface; see the switcher’s manual).

ID Button (Front)

The ID button on the front can be used to toggle between static and DHCP IP

addressing, assign a device address, reset the factory defaults, and restore the factory

firmware image (for details, see the manual).

Additional Information Covered in Manual

For information on the following, see the Hardware Reference Manual – DXLink Twisted

Pair Transmitters/Receiver at www.amx.com :

• Audio precedence; pinouts for VGA, component, S-Video, and composite

• NetLinx control and programming commands; Telnet commands

• IR file transfers; upgrading firmware image; restoring factory default settings

Reference Documents

• Instruction Manual – Enova DGX 8/16/32/64 Digital Media Switchers

• Hardware Reference Manual – Enova DGX 100 Series Digital Media Switchers

• Instruction Manual – Enova DVX-315XHD/21XXHD All-in-One Presentation

Switchers

• White Paper: Cabling for Success with DXLink

• WebConsole & Programming Guide – NX-Series Controller

FIG. 6 ATTACH SIGNAL, TRANSPORT, AND CONTROL CABLES

FIG. 7 ATTACH SIGNAL, TRANSPORT, AND CONTROL CABLES ON DXLINK HDMI RECEIVER

INDICATOR LEDS NORMAL POWER UP INDICATES

Power Green Power is applied

Digital Video and Audio Green Video and HDMI embedded

audio are present

Multi-Format - C, Y/C

Y/PB/PR, RGB

RGBHV, RGBS

Green or Off

(only one of the three

can be green at a time)

Corresponding signal is

present

RX - Scaling: Bypass/Auto/Manual One green, two off Current scaling mode*

232 (serial) TX / 232 (serial) RX Red/Yellow Serial activity

NetLinx Link/Act Green (Blinking - #3

Toggle OFF)

Active LAN connection to

an AMX Network

NetLinx Status Green LAN activity

CEC OFF Not currently supported

USB Yellow Connected to device

HDMI In Ground screw

DXLink output

ICS LAN 10/100 port

Digital Audio In

Stereo Audio In

USB port

Video In (analog)

Produktspecifikationer

Varumärke:	AMX
Kategori:	Inte kategoriserad
Modell:	DX-TX

Behöver du hjälp?

Om du behöver hjälp med AMX DX-TX ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad AMX Manualer

AMX HPX-MSP-7-SL Bruksanvisning

25 September 2024

AMX HPX-MSP-10-SL Bruksanvisning

25 September 2024

AMX TPC-WIN8-TAB Bruksanvisning

24 September 2024

AMX NMX-DEC-N1222A Bruksanvisning

23 September 2024

AMX NMX-DEC-N2222A Bruksanvisning

23 September 2024

AMX NMX-DEC-N1233 Bruksanvisning

23 September 2024

AMX NMX-DEC-N2211 Bruksanvisning

23 September 2024

AMX NMX-ENC-N1134A Bruksanvisning

23 September 2024

AMX NMX-ENC-N1133 Bruksanvisning

23 September 2024

AMX NMX-ENC-N2315-WP Bruksanvisning

23 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024