Apart SB160 Bruksanvisning

Apart mottagare SB160

Läs nedan 📖 manual på svenska för Apart SB160 (4 sidor) i kategorin mottagare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
SB-160
OWNER’S MANUAL
SOUNDBLOCKSOUNDBLOCK
• Read all documentation before operating your equipment.
Retain all documentation for future reference.
• Save the carton and packing material even if the equipment has arrived in good condition.
Should you ever need to ship the unit, use only the original factory packing.
• Do not spill water or other liquids into or on the unit.
• Make sure power outlets conform to the power requirements listed on the back of the unit.
• Do not use the unit if the electrical power cord is frayed or broken.
• Always operate the unit with the AC ground wire connected to the electrical system ground.
• Have gain controls on amplifiers turned down during power-up to prevent
speaker damage if there are high signal levels at the inputs.
• Do not connect the inputs / outputs of amplifiers or consoles to any other voltage source,
such as a battery, mains source, or power supply, regardless of whether
the amplifier or console is turned on or off.
• Power down & disconnect units from mains voltage before making connections.
• Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
• Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an
environment which may distort the normal flow of air around the unit. If the unit is used in an
extremely dusty or smoky environment, the unit should be periodically "blown free" of dust.
• Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages.
• Do not drive the inputs with a signal level greater than that required to drive equipment
to full output.
• Do not run the output of any amplifier back into another input.
• Do not ground the red output terminal, never connect a red output terminal to
another red output terminal.
• In case of mal-function this device should be serviced by qualified service personnel only.
SAFETY INFORMATION
!
!
!
!
!
C A U T I O N
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER OR BACK
NO USER-SERVICEABLE PARTS INSIDE
SERVICING ONLY FOR QUALIFIED PERSONNEL
1. Protection Led:
The Protection Led illuminates RED
when the amplifier is overheated or
when a shorted load or DC is
detected on the amplifier output.
The amplifier shall reset itself when
the problem is solved.
2. Signal LED indicator L & R
These LED’s will light up green when
the input detects audio signal.
3. Peak LED/limiter L & R
These red LED’s illuminates if the input signal of the amplifier is to high. Occasional blinking of these LED’s
is acceptable, but if it remains (on) or more than intermittently, then you should lower the input level or reduce the output
level of the preceeding component to avoid audible distortion.A built-in limiter will prevent excessive RMS clipping.
Remove Jp4 (Left channel) and Jp3 (Right channel) to de-activate this limiter function.
Please contact a qualified technician.
4. Level control L & R
These volume knobs are used to adjust the level of the outputs to the speakers.
5. Power switch
switch to 'ON' position to turn power on, and to 'OFF' to turn power off.
6. Monitor Jack
A stereo headphone can be inserted to this Jack for monitoring the amplifier output.
9. Unbalanced input cinch L & R
Cinch-RCA connectors for applying the input signal for the left and right channel.
10. Speaker output terminals connecting the speaker system
The minimum load is 4 ohms per channel. of course,
higher loads are acceptable.4 ohm=min. 4 pcs. of 16 ohm speakers wired
in parallel or max. 2 pcs. of 8 ohm speakers wired in parallel.
Please note that 2 pcs. of 6 ohm speakers wired in parallel are NOT allowed.
11. AC outlet un-switched)/AC input
Use AC cord connect to the AC input to a AC socket.
Use the AC outlet to power other modules (with the MB-AC link cable) or to other associated equipment.
AC voltage is always present as long as the amplifier is connected to the AC voltage source.
12. AC fuse
It the fuse is blown, please disconnect the power cord, and replace fuse by the same value 3.15 AT
of the SLOW BLOW type. If the fuse blows again, then contact your dealer for further servicing.
13. Mono - Stereo switch
Mono Stereo switch for the input signal.
14. Low cut filter
Switches on a high pass filter of 100Hz. This features can be used for driving small or horn speakers.
10
9
11
12
13
12
3
4
6
5
SOUNDBLOCK SOUNDBLOCK
14
NOT ALLOWED
2 X 80 / 120 Watt
2 X 60 / 90 Watt
0.775 Vrms/MAX input level +14dBV
20 Kohm
15hz - 30KHz
<0.03%
(4 ohm) >400
300 VA MAX
70 X 140 X 335 MM
Net. 2.8 Kg
Power Rated / Max
2 ohm
4 ohm
8 ohm
Input Sensitivity
Input impedance
Freq. Response
Total harm. distortion
Damping factor
Power consumption
Dimensions (H x W x D):
Weight
Technical specifications SBR160
• Due to the built-in limiter, some values may differ from the specs listed above.
Due to our continuous research and development, the product specifications may
change without prior notice at any time.
• The turning speed of the cooling fan is related to the temperature of the amplifier.
When the amplifier is cold it’s normal that the fan doesn’t turn.
Only if a lot of output-power is requested the fan will turn.
• A built-in limiter will prevent excessive RMS clipping.
Remove Jp4 (Left channel) and Jp3 (Right channel) to de-activate this limiter function.
• If ‘Hum’ or Buzz’ occurs when connecting different inputs, then this is often caused by
‘GROUND or EARTH LOOPS’.
Inside you can disconnect Jp5 to break this ground loop.
Please contact a qualified technician to do this.
SPECIAL FEATURES
SPECIFICATIONS

Produktspecifikationer

Varumärke: Apart
Kategori: mottagare
Modell: SB160

Behöver du hjälp?

Om du behöver hjälp med Apart SB160 ställ en fråga nedan och andra användare kommer att svara dig


mottagare Apart Manualer

Apart

Apart SBR160 Bruksanvisning

14 Oktober 2024
Apart

Apart REVAMP1680 Bruksanvisning

1 September 2024
Apart

Apart REVAMP2060T Bruksanvisning

28 Augusti 2024
Apart

Apart MA35 Bruksanvisning

26 Augusti 2024
Apart

Apart CHAMP-3D Bruksanvisning

24 Augusti 2024
Apart

Apart MA125 Bruksanvisning

24 Augusti 2024
Apart

Apart CHAMP-ONE-SLV Bruksanvisning

23 Augusti 2024
Apart

Apart PA8250 Bruksanvisning

22 Augusti 2024
Apart

Apart CONCEPT1T Bruksanvisning

21 Augusti 2024
Apart

Apart MA200 Bruksanvisning

21 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Yamaha

Yamaha Aventage RX-A4A Bruksanvisning

9 April 2025
Yamaha

Yamaha Aventage RX-A8A Bruksanvisning

9 April 2025
Phonocar

Phonocar PH544 Bruksanvisning

5 April 2025
DJI

DJI D-RTK 3 Bruksanvisning

4 April 2025
Alpine

Alpine MRX-F65 Bruksanvisning

2 April 2025
QSC

QSC SPA-Qf 60x2 Bruksanvisning

2 April 2025
Harper

Harper HDT2-5010 Bruksanvisning

2 April 2025
Harper

Harper HDT2-2010 Bruksanvisning

2 April 2025
Pro-Ject

Pro-Ject Stereo Box DS Bruksanvisning

30 Mars 2025
Streacom

Streacom TL1 Bruksanvisning

30 Mars 2025