Astralpool HydroSpin Compact Bruksanvisning

Astralpool Vattenfilter HydroSpin Compact

Läs nedan 📖 manual på svenska för Astralpool HydroSpin Compact (20 sidor) i kategorin Vattenfilter. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/20

H y d r o S p i n

INSTALLATION AND MAINTENANCE MANUAL

MANUEL D’INSTALLATION ET D’ENTRETIEN

MANUAL DE INSTALACIÓN Y MANTENIMIENTO

MANUALE DI INSTALAZIONE E MANUTENZIONE

EINBAU-UND BETRIEBSANLEITUNG

MANUAL DE INSTRUÇÕES E MANUNTENÇÃO

Compact

1 4 3

ENGLISH

IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be

implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before

beginning installation and start-up.

Keep this manual for future reference.

To achieve optimum performance of the HydroSpin Compact, follow the instructions provided below:

1. CONTENTS

Inside the box you will find the following components:

1. HydroSpin Compact

2. Multi-support

3. Bag of accessories*

4. Installation and maintenance manual

*Ball valve 3/4" Stainless Steel AISI 316, 2

connections for glueing Ø50 or screwing to 2 1/4", 2

joints, 1 outlet elbow, 3 nuts and 3 anchor bolts.

2. GENERAL CHARACTERISTICS

The HydroSpin has been designed to work in all new and existing water installations.

Installing the HydroSpin in filtration systems from 3 to 16,5 m³/h and up to a maximum pressure of 2.5 bars is

recommended.

The HydroSpin:

 Significantly reduces water lost in drainage when cleaning the filters.

 Reduces the frequency with which the filtration system is cleaned.

The HydroSpin accumulates the separated solids in its lower part, which are then ejected by opening the purge

valve. This should be opened before the waste surpasses the limit indicated in Fig. 1 - pag.16.

3. INSTALLATION

The HydroSpin should be installed between the pump and the filter.

Ensure there is a drain in the area where the HydroSpin is located.

Ensure that the HydroSpin is installed on a horizontal surface.

There should be sufficient space around the HydroSpin to carry out

the inspections and maintenance that will be necessary during its

lifetime.

Wall installation:

1. Mark the three holes on the wall of the support.

2. Make the 3 Ø 8mm holes.

3. Screw in the support.

4. Position the Hydrospin Compact.

5. Join simple or 3 piece unions of Ø50 in the HydroSpin entrance

and exit.

6. Using valves in both the entrance and exit is recommended.

7. Thread the purge valve into the

lower part of the HydroSpin,

putting teflon in the thread.

Check that it is closed.

8. Join tubing from the HydroSpin

purge, to drainage (Fig. 2 -

pag.16).

9. Installation of a manometer in

the HydroSpin inlet is

recommended. (Fig. 3 - pag.16).

10. Switch on the pump.

Soil installation:

1. Mark the three holes on the wall of the support.

2. Make the 3 Ø 8mm holes.

3. Follow on from point 5 in the previous section.

Note: an electrovalve may be connected to the purge exit in order to temporize

cleanings.

4. MAINTENANCE

Purging: before the limit set out in Fig. 1 - pag.16 is reached, the HydroSpin should

be purged by opening the lower valve when accumulated waste can be seen.

When carrying out this operation it is neither necessary to stop the filter system nor

to turn the filter valve key.

5. TROUBLE-SHOOTING

If you notice that the pressure reading has risen considerably on the HydroSpin entrance manometer, it may be due

to:

a) The filter is dirty: check the pressure of the filter's manometer, and if it has risen, carry out its cleaning

operation. (Follow the steps in the filter's instruction manual). Afterwards, check that the HydroSpin's

entrance manometer pressure has decreased.

b) The HydroSpin is blocked: check the pressure of the Filter's

manometer, if this is the same or the pressure has decreased, it

means that there is one or more blockages within the HydroSpin,

in which case the following steps must be taken to unblock it:

1. Stop the filtration system.

2. Shut off the system's suction and discharge valves.

3. Purge the waste and water by opening the lower valve.

4. Unscrew the two nuts in the 8 caps.

5. Separate the central body, taking care with the joint.

6. Separate the diffuser (pressure)

7. To extract the body of cyclones, turn them firmly to the right

until snug (about 2 centimetres of movement)

8. Take out the 6 top screws.

9. Check that there are no obstructed cyclones (holes) and wash

the whole piece with pressurized water, going over all the

cyclones once again.

10. Once everything has been washed, assemble the whole in

reverse order to that described above, position the joint

snugly in its place and screw in the 8 screws around the

perimeter tightly.

Attention:

 If you detect that the accumulated dirt inside the Hydrospin Compact has a

very uneven surface it is possible that there is some obstruction in one of the

cyclones, follow step b) described previously (Fig. 4 page. 16).

 When it is running check that the HydroSpin does not lose water through

the caps.

 Check that the pressure on both the HydroSpin and Filter manometers is similar.

6. SAFETY WARNINGS

 Do not install HydroSpin in facilities with a cleaning system with active oxygen or its derivates.

 Do not connect the HydroSpin directly to the water network as the pressure may be very high and exceed the

maximum pressure supported by the equipment.

 Do not use the filtration circuit for filling up and regulating the swimming pool water level. An error in its use

could cause overpressure in the filter.

 Do not clean the e its propertiquipment with any kind of solvent, as it could lose es (shine, transparency...)

 In filtration installations with diatomeaceous filters, a bypass between the pump and the filter must be made so

that the HydroSpin does not separate the diatomeaceous earth when it is introduced into the filtration system;

the when doing so close the connections to the HydroSpin.

Produktspecifikationer

Varumärke:	Astralpool
Kategori:	Vattenfilter
Modell:	HydroSpin Compact
Enhetsplacering:	Aanrecht
Innehåll (inuti):	33 l
Typ av operation:	Touch
Magnetronkraft:	1000 W
Power grill:	1200 W
Färg på produkten:	Zwart, zilver
Antal effektnivåer:	8
Skivspelare:	Ja
Skivbordsstorlek:	360 mm
Inbyggd display:	Ja
Timer:	Ja
Vikt:	28900 g
Bredd:	487 mm
Djup:	541 mm
Höjd:	377 mm
Nettoskatt:	2200 W
Uppvärmningsfunktion:	Ja
Grill:	Ja
Sladdlängd:	0.9 m
Förpackningens vikt:	31300 g
Förpackningens bredd:	563 mm
Djuppackning:	595 mm
Förpackningshöjd:	443 mm
Integrerad klocka:	Ja
Typ av klocka:	Elektronisch
Konvektionsmatlagning:	Ja
Ångkokning:	Ja
Håll varm funktion:	Nee
Rotisserie:	Nee
Avfrostningsfunktion:	Ja
Användarmanual:	Ja
Nuvarande:	11 A
Typ grill:	Quartz-grill
Förkorta:	Ja
AC-ingångsspänning:	230 V
AC-ingångsfrekvens:	50 Hz
Typ produkt:	Combinatiemagnetron
Type beeldscherm:	LCD