Atlas Sound FM250-4 Bruksanvisning

Atlas Sound mottagare FM250-4

Läs nedan 📖 manual på svenska för Atlas Sound FM250-4 (3 sidor) i kategorin mottagare. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/3
– 9 – AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250-4 and FM250-70 Module Features
1. Module Status Indicators
Note: They also parallel Status LED on the front panel of the F6-MF panel.
Ready This LED will illuminate Green when an FM250 power module is installed on the appropriate channel and the F6-MF is
turned on.
Signal The channel Signal LED will illuminate Green when the FM250 amplifier output signal produces a minimum 1 Watt
output.
Limit The Limit LED will illuminate Yellow under load conditions. If the FM250 function switch is set to Limit then the LED
acts as a maximum level indicator. If the FM250 channel Limit function is off, the LED reacts as a Clip indicator. Also,
under Low Impedance loads, this LED serves as a current Limit indictor.
Protect The Protect LED will illuminate Red during one the following conditions. No output will occur while this LED is
illuminated. It will reset itself after the condition has been corrected.
1) Shorted speaker output.
2) Thermal Shut Off. The Temp F6-MF TEMP LED will also be illuminated.
3) Current Overdrive. If the amplifier channel is driving too low of a speaker load.
2. Speaker Connections
A removable Phoenix/Euro Block type connector is supplied to connect your speakers to the FM250 amplifier module. It is
recommended to use 16-gauge wire or lower for connection to the speakers. Do not overload the amp by connecting too many Note:
speakers to the amp.
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
4Ω
FM250 - 4
250W @ 4Ω
Protect
Limit
Signal
Ready
Speaker Output
Class 2 Wiring
70V
FM250 -70
250W @ 70V
AtlasSound.com – 10 –
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250-4 & FM250-70 Function Switch
FM250 Module Dip Switch Functions are located near the rear of the FM250 modules. It is essential to preset your setting prior Note:
to inserting the module into the F6-MF.
Factory Dip Switch Presets
Dip Switch 1 ships in the “On” position. Dip Switches 2 & 3 ship in the “Off” position.
Dip Switch 1, Gain
When placed in the “On” position the channel’s Gain or Input Sensitivity will be 1V (0dBV) for rated output. When placed in the “Off”
position the Gain is set to 2V (6dBV).
Dip Switches 2 & 3, HPF
The High Pass Filter (HPF) when placed into the “On” position engages a 100Hz / 12dB filter. When in the “Off” position the module
operates at full audio bandwidth.
– 11 – AtlasSound.com
Specifications are subject to change without notice.
Owner’s Manual
F6-MF
Multi-Impedance Modular Amplifier
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Telephone: 800.876.3333 • Fax: 800.765.3435
FM250 Amplifier Module Installation
Use the following steps and read all steps prior to installation.
1. Turn F6-MF AC Power Switch to the “Off” position.
2. Turn down all level controls on the front panel.
3. Remove the blank card slot cover. Do not discard the two screws, you will need them later.
4. Set the function switches on the FM250 module. (See Page 10)
5. Carefully and slowly guide the module into the slot with the PCB components facing to the right. The module heatsink Note:
top and bottom metal edge mate with the mainframe plastic card guides. Do not force the card. Realign if necessary.
6. After the module is pushed in and in contact with the back plane of the PCB assembly mating connector, firmly press the
module in completing the connection. If the module plate is flush to the F6-MF, the module is fully seated.
7. Insert the two screws from the cover pate. Some minor alignment may be required.
Align Modules to
Top & Bottom Card
Guides

Produktspecifikationer

Varumärke: Atlas Sound
Kategori: mottagare
Modell: FM250-4

Behöver du hjälp?

Om du behöver hjälp med Atlas Sound FM250-4 ställ en fråga nedan och andra användare kommer att svara dig


mottagare Atlas Sound Manualer

Atlas Sound

Atlas Sound PA702 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound AA35 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound AA-GPN1200 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound AP-S15L Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound AP-S15 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound AL2430 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound T112 Bruksanvisning

19 December 2024
Atlas Sound

Atlas Sound DPA-DAC4 Bruksanvisning

25 September 2024
Atlas Sound

Atlas Sound HPA-DAC2 Bruksanvisning

25 September 2024
Atlas Sound

Atlas Sound CLA402 Bruksanvisning

25 September 2024

mottagare Manualer

Nyaste mottagare Manualer

ETON

ETON MA 1 Bruksanvisning

19 Mars 2025
Elipson

Elipson P1 Bruksanvisning

14 Mars 2025
Elipson

Elipson Stream S300 Xi Bruksanvisning

14 Mars 2025
Elipson

Elipson WIIM Mini Bruksanvisning

14 Mars 2025
Rexing

Rexing RoadMate CPStream Bruksanvisning

13 Mars 2025
KanexPro

KanexPro SP-1X16SL18G Bruksanvisning

13 Mars 2025
Marshall Electronics

Marshall Electronics VDA-108-3GS Bruksanvisning

13 Mars 2025
Rega

Rega Brio MK7 Bruksanvisning

12 Mars 2025
Mtx Audio

Mtx Audio Thunder TH2500.1 Bruksanvisning

11 Mars 2025
Mtx Audio

Mtx Audio Thunder TH1500.1 Bruksanvisning

11 Mars 2025