Audio-Technica ES925C/DS5 Bruksanvisning

Audio-Technica mikrofon ES925C/DS5

Läs nedan 📖 manual på svenska för Audio-Technica ES925C/DS5 (4 sidor) i kategorin mikrofon. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
1
■Introduction
Thank you for purchasing this product. Before using the product, read through
the user manual to ensure that you will use the product correctly. Please keep
this manual for future reference.
■Features
• Modular microphone system comprised of an ES Series capsule, gooseneck
assembly, and power module.
• RGB LEDs built into both the desk stand power module and gooseneck
assembly indicate the on/off status of the microphone.
• Includes external control function for device control from the capacitive touch
switch.
• The capacitive touch switch can be set to any of three operating modes:
“touch-on/touch-off”, “touch-to-talk” and “touch-to-mute”.
■Safety precautions
Although this product was designed to be used safely, failing to use it correctly
may result in an accident. To ensure safety, observe all warnings and cautions
while using the product.
■Cautions for the product
• Do not subject the product to strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a
hot, humid or dusty place.
■Notes on use
• Do not swing or pull the product. Doing so may cause disconnection or
damage.
• The circuitry in the microphone takes about 30 seconds to stabilize after power
is supplied. You may hear some audio disturbance during startup.
• The connectors are equipped with a special RFI-shielding mechanism. If you
remove or replace the connector, you may adversely affect the microphone’s RFI
immunity. The Audio-Technica Crimp Tool (ATCT) and shield parts are required to
shorten the cable and reinstall the connector while maintaining the RFI immunity.
• Install the microphone on a flat, unobstructed mounting surface. Make sure
that the sound source is not below the mounting surface.
• Depending on the surface finish of a table, the desk stand power module may
leave marks on the table.
• Do not excessively bend the gooseneck assembly, rotate the ends of the
capsule, or pull on them. Doing so may cause disconnection or malfunction.
• The product is a modular system comprised of a microphone element,
gooseneck assembly and power module. Make sure the parts are firmly
attached before use.
• Do not remove the rubber O-ring on the power module connecting part at the
lower section of the gooseneck assembly.
• When attaching parts, remove the black cap on the capsule connecting part
of the gooseneck assembly. Do not remove the silicone part at the end of
the capsule connecting part.
Silicone part
Do not remove
■Switch settings
To reduce low-frequency ambient noise (such as footsteps or air conditioning
noise), room reverberation, and mechanically coupled vibrations as much as
possible, turn on the low-cut filter switch ( ) on the bottom of the power
module.
ES925C6/DS5
ES925C12/DS5
ES925C15/DS5
ES925C18/DS5
ES925C21/DS5
ES925C24/DS5
User Manual
CARDIOID CONDENSER
MODULAR GOOSENECK MICROPHONE
WITH 5-PIN DESK STAND POWER MODULE
2
■Assembly
1. • Insert the gooseneck assembly (c) while rotating it into the desk stand
power module (d).
• Tighten until it does not rotate, and use the hex wrench (h) to tighten the
set screw (g) and set the gooseneck assembly in place.
• Connect the capsule (b) to the gooseneck assembly, and attach the
windscreen (a).
* If the parts are not sufficiently tightened together, problems may occur
such as the LED colors of the gooseneck assembly and power module
not matching or sound is not output.
a
b
c
g
h
d
2. Connect the included cable to the connector (e) on the reverse side of the
desk stand power module, and pass the cable through the wire slot (f).
e
f
■LED color
1 2 3
OFF RED GREEN
YELLOW
4 5 6 7
BLUE
MAGENTA
CYAN WHITE
■Wiring
1
2
5
3
4
SHIELD : GND (PIN1)
YELLOW : HOT (PIN2)
RED : COLD (PIN3)
BLACK : GND (PIN1)
BLUE : CONTACT CLOSURE (PIN5)
WHITE : LED CONTROL (PIN4)
3
■Switch setting and functions
Contact
Closure
GND
MIC
4
6
7. LED status
3. Action 4. Contact
closure
status
2. Switch
Function 6. LED color
5.
Audio
status
1. Control

Produktspecifikationer

Varumärke: Audio-Technica
Kategori: mikrofon
Modell: ES925C/DS5

Behöver du hjälp?

Om du behöver hjälp med Audio-Technica ES925C/DS5 ställ en fråga nedan och andra användare kommer att svara dig


mikrofon Audio-Technica Manualer

Audio-Technica

Audio-Technica ATH-PDG1a Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica ATH-770XCOM Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica BP899LcH-TH Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica BP898cW Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica BP899c Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica BP899cH Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica BP899L Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica U857QSU Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica AT881TL/RC Bruksanvisning

7 December 2024
Audio-Technica

Audio-Technica U857QL Bruksanvisning

7 December 2024

mikrofon Manualer

Nyaste mikrofon Manualer

Vonyx

Vonyx CMS320B Bruksanvisning

16 Januari 2025
Karma

Karma SET 6252A Bruksanvisning

16 Januari 2025
DJI

DJI Mic Mini Bruksanvisning

15 Januari 2025
Sound Devices

Sound Devices Astral A20-HH Bruksanvisning

14 Januari 2025
HyperX

HyperX QuadCast S Bruksanvisning

8 Januari 2025
Monacor

Monacor ECM-306BU/SW Bruksanvisning

8 Januari 2025
Schertler

Schertler STAT-C Bruksanvisning

7 Januari 2025
Godox

Godox Cube-C Bruksanvisning

7 Januari 2025
Audibax

Audibax AWM 401 TD Bruksanvisning

6 Januari 2025
Audibax

Audibax Sidney 1250 A Bruksanvisning

6 Januari 2025