Audio-Technica ES925ML/FM3 Bruksanvisning

Audio-Technica mikrofon ES925ML/FM3

Läs nedan 📖 manual på svenska för Audio-Technica ES925ML/FM3 (3 sidor) i kategorin mikrofon. Denna guide var användbar för 14 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

ES925ML6/FM3

ES925ML12/FM3

ES925ML15/FM3

ES925ML18/FM3

ES925ML21/FM3

ES925ML24/FM3

User Manual

MICROLINE CONDENSER

MODULAR GOOSENECK MICROPHONE

WITH 3-PIN FLUSH-MOUNT POWER MODULE

■Introduction

Thank you for purchasing this product. Before using the product, read through

the user manual to ensure that you will use the product correctly. Please keep

this manual for future reference.

■Features

• Modular microphone system comprised of an ES Series capsule, gooseneck

assembly, and power module.

• RGB LEDs built into both the flush-mount power module and gooseneck

assembly indicate the on/off status of the microphone.

• Capacitive touch switch for microphone control.

• Three-pin output power module allows for inconspicuous tabletop installation.

■Safety precautions

Although this product was designed to be used safely, failing to use it correctly

may result in an accident. To ensure safety, observe all warnings and cautions

while using the product.

■Cautions for the product

• Do not subject the product to strong impact to avoid malfunction.

• Do not disassemble, modify or attempt to repair the product.

• Do not handle the product with wet hands to avoid electric shock or injury.

• Do not store the product under direct sunlight, near heating devices or in a

hot, humid or dusty place.

■Notes on use

• Check the strength of the mounting area. Insufficient strength or poor

mounting will cause objects to fall or become damaged.

• The circuitry in the microphone takes about 30 seconds to stabilize after power

is supplied. You may hear some audio disturbance during startup.

• Install the microphone on a flat, unobstructed mounting surface.

• Depending on the surface finish of a table, the isolators may leave marks on

the table.

• Do not excessively bend the gooseneck assembly, rotate the ends of the

capsule, or pull on them. Doing so may cause disconnection or malfunction.

• The product is a modular system comprised of a microphone element,

gooseneck assembly and power module. Make sure the parts are firmly

attached before use.

• Do not remove the rubber O-ring on the power module connecting part at the

lower section of the gooseneck assembly.

• When attaching parts, remove the black cap on the capsule connecting part

of the gooseneck assembly. Do not remove the silicone part at the end of

the capsule connecting part.

Silicone part

Do not remove

■Assembly

• Insert the gooseneck assembly (c) while rotating it into the flush-mount power

module (d).

• Tighten until it does not rotate, and use the hex wrench (i) to tighten the set

screw (h) and set the gooseneck assembly in place.

• Connect the capsule (b) to the gooseneck assembly, and attach the windscreen

(a).

* If the parts are not sufficiently tightened together, problems may occur such as

the LED colors of the gooseneck assembly and power module not matching or

sound is not output.

• Refer to the LED table to the right and set the LED color before attaching to

the mounting surface.

• If you are installing the flush-mount power module on a table without the

isolators, you must make a hole with a diameter of 20.5 mm in the mounting

surface.

• If you are installing with the isolators, the hole must have a diameter of 23.5

mm. Inserting the isolators between the mounting surface and power module

allows you to separate the flush-mount power module from the mounting

surface.

• Attach the upper part isolator (e) to the mounting surface, and attach the flush-

mount power module (d). Attach the lower isolator (f) to the reverse side of the

mounting surface, and then tighten the nut (g).

■Switch setting and functions

1. Action

2. Audio

status

3. LED color 4. LED status

■LED color

1 2 3

OFF RED GREEN

YELLOW

4 5 6 7

BLUE

MAGENTA

CYAN WHITE

■Wiring

1 2

PIN1

(Ground)

PIN2

(Hot)

PIN3

(Cold)

■Specifications

ES925MLx/FM3

Element Fixed-charge back plate, permanently polarized condenser

Polar pattern Line + Gradient

Frequency response 30 - 20,000 Hz

Open circuit sensitivity -35 dB (17.7mV) (0dB=1V/Pa, 1kHz)

Impedance 180 ohms

Maximum input sound

level 137 dB SPL (1kHz at 1% THD)

Dynamic range 114 dB (1kHz at Max SPL)

Signal-to-noise ratio 71 dB (1kHz at 1Pa, A-weighted)

Phantom power

requirements 22 - 52 V DC, 8 mA

Weight

ES925ML6/FM3: 114.2 g (4.0 oz)

ES925ML12/FM3: 138.2 g (4.9 oz)

ES925ML15/FM3: 143.2 g (5.1 oz)

ES925ML18/FM3: 148.2 g (5.2 oz)

ES925ML21/FM3: 153.2 g (5.4 oz)

ES925ML24/FM3: 158.2 g (5.6 oz)

Dimensions

ES925ML6/FM3: 326.5 mm (12.9“) x 38 mm (1.5“) x 48 mm (1.9“)

ES925ML12/FM3: 434 mm (17.1“) x 38 mm (1.5“) x 48 mm (1.9“)

ES925ML15/FM3: 510.2 mm (20.1“) x 38 mm (1.5“) x 48 mm (1.9“)

ES925ML18/FM3: 586.4 mm (23.1“) x 38 mm (1.5“) x 48 mm (1.9“)

ES925ML21/FM3: 662.6 mm (26.1“) x 38 mm (1.5“) x 48 mm (1.9“)

ES925ML24/FM3: 738.8 mm (29.1“) x 38 mm (1.5“) x 48 mm (1.9“)

(H×W×D)

Output connector 3-Pin XLRM-type

Optional interchangeable

elements ESE-Ca (120°), ESE-Ha (100°), ESE-Oa (360°)

Included accessories Isolator 1 pair, Nut, Windscreen AT8138a,

Set screw (M2×2 mm (0.08“)) 2 pcs., Hex wrench (0.89 mm (0.04“))

x = 6/12/15/18/21/24

142419802-02-01 ver.1 2019.06.01

■Polar pattern

240˚

180˚

210˚

270˚

300˚

330˚

0˚

150˚

120˚

90˚

30˚

60˚

SCALE IS 5 DECIBELS PER DIVISION

200 Hz

1 kHz

5 kHz

8 kHz

LEGEND

■Frequency response

5020 20k10k5k2k1k500200100

Response in dB

Frequency in Hertz

LEGEND

0°, 50cm

■Dimensions

ES925ML6/FM3 ES925ML12/FM3 ES925ML15/FM3 ES925ML18/FM3 ES925ML21/FM3 ES925ML24/FM3

ES8755R (FM3)

(unit: mm)

38.0

434.0

510.2

586.4

662.6

738.8

48.0

20.0

10dB

Audio-Technica Corporation

2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan

Global Support Contact: www.at-globalsupport.com

Made in Japan

φ8.0

326.5

Produktspecifikationer

Varumärke:	Audio-Technica
Kategori:	mikrofon
Modell:	ES925ML/FM3
Färg på produkten:	Black, White
Vikt:	2200 g
Tillgångar:	1040 W
På / Av knapp:	Ja
Antihalkfötter:	Ja
Kapacitet i koppar:	16 kopjes
Mätglaset:	Ja
Innehåll:	3.8 l
Mått (B x D x H):	152.4 x 228.6 x 304.8 mm
AC-ingångsspänning:	120 V
AC-ingångsfrekvens:	60 Hz