Auray CFC-68 Bruksanvisning

Auray Inte kategoriserad CFC-68

Läs nedan 📖 manual på svenska för Auray CFC-68 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

Cable Replacement Kit

CFC Series

Owner’s Manual

for CFP Series Carbon Fiber Boom Poles

Introduction

Thank you for choosing Auray.

The Auray CFC replacement kit provides a

replacement cable for the Auray CFP carbon ﬁber

boom pole. Auray’s solderless design provides a

fast and easy solution for cable replacement.

The high-quality coiled cable features a right-angle

XLR connector manufactured by Neutrik®, and a

TA3 (mini XLR) connector manufactured by Rean®

(a registered trademark of Neutrik®) for secure

locking connections and ﬂawless signal transfer.

This cable also features Auray’s unique strain relief

system that absorbs tension and protects the cable

from damage at the edge of the tip exit and at the

T3 connector. The included hex key and a small

slotted screwdriver (not included) are the only tools

needed for this cable replacement procedure that

will assure long-lasting and trouble-free operation

of your CFP boom pole.

Right-angle

XLR connector

TA3 (mini XLR)

connector

Coiled XLR

cable

Tip strain relief

Nylon line

1.5 mm hex

key

Replacing the Cable – Boom Pole with

Bottom Exit XLR

Remove the old cable

1. Use the hex key to

loosen the set screw

on the tip. 1

2. Remove the tip by

unscrewing it. 2

3. Lift the cable and

strain relief out of the

tip exit slot. 3

Tip: Before

proceeding, push a

small length of cable

into the tube from the

tip of the pole. This

will give you enough

slack to complete the

following steps.

4. Unscrew the bottom

housing from the base

of the boom pole. 4

5. Unscrew the plastic

TA3 strain relief. 5

6. Disconnect the TA3

connector by pressing

on the locking tab and

gently removing the

connector from the

mount.

Note: The TA3

connector should

easily disconnect. Do

not force or pull on the

cable to disconnect

it. Doing so could

damage the housing

or the connector.

7. Use a small slotted

screwdriver to reach

inside the strain

relief and depress the

locking tab of the TA3

connector. 6 With the

locking tab depressed,

you can slide the

strain relief over the

TA3 connector and

o of the cable. Set

the strain relief piece

aside.

Alternative: Use a wire cutter to snip the cable

at the base of the TA3 connector. Remove the

strain relief, and set it aside.

Important: Once you have performed this step,

the cable will be unusable. If you plan on using

the cable again at a later point, don’t proceed

with this alternative step.

8. Remove the cable by pulling it out from the

top of the pole.

Instructions

Install the replacement cable

1. Holding the boom

pole upright, insert

the replacement

cable into the top of

the boom pole, 1

and snake it through

the tubing until

the TA3 connector

is exposed at the

bottom of the pole. 2

Note: If the cable

does not move

smoothly through

the tubing, use the

included nylon line:

tie the line to the TA3

connector and drop

it through the tubing

from the top. 3

Pull

the string from the

bottom of the boom

pole to snake the

cable through the

tubing. Make sure

to remove the line

before continuing.

2. Fit the narrow side of

the strain relief over

the TA3 connector,

and push it past the

TA3 connector’s

locking tab. 4

3. Plug the TA3

connector to the

bottom housing

by inserting it into

the TA3 mount and

pushing in until it

clicks.

Note: When properly

aligned, the TA3

connector will easily

slide into place. Do

not try to force the connector into the mount.

Doing so could damage the connector or the

mount.

4. Screw the threaded end of the strain relief onto

the threaded ﬁtting on the bottom housing. 5

5. Screw the bottom housing onto the end of the

boom pole. 6

6. Place the strain relief of the cable into the tip

exit slot.

7. Replace the tip by screwing it on, and secure it

by tightening the set screw with the hex key.

Produktspecifikationer

Varumärke:	Auray
Kategori:	Inte kategoriserad
Modell:	CFC-68
Färg på produkten:	Zwart
Vikt:	20000 g
Bredd:	690 mm
Djup:	170 mm
Höjd:	3280 mm
Förpackningens vikt:	20000 g
Förpackningens bredd:	185 mm
Djuppackning:	1610 mm
Förpackningshöjd:	175 mm
Snäll:	Vaste vloerstandaard
Husmaterial:	Aluminium, Steel
Typ av förpackning:	Doos
Justerbar i höjdled:	Ja
Monteringsmetod:	Vloer
Maximal viktkapacitet:	90 kg
Certifiering:	CE
Panelmonteringsgränssnitt:	100 x 100,600 x 400,800 x 600 mm
Kompatibilitet med monteringsgränssnitt (min):	100 x 100 mm
Kompatibilitet med monteringsgränssnitt (max):	800 x 600 mm
Antal skärmar som stöds:	3
Förbättrad kabelhantering:	Ja
(Inre) fraktpaketets vikt:	20000 g
Maximal skärmstorlek:	65 "
(Inner) fraktpaketets höjd:	175 mm
(Inre) fraktpaketets bredd:	185 mm
(Inre) fraktpaketets längd:	1610 mm
Produkter per (inner) fraktförpackning:	1 stuk(s)
Minsta skärmstorlek:	40 "
Höjdjusteringsområde:	580 - 1550 mm
Typ av höjdjustering:	Handmatig