Azden WL/T-PRO Bruksanvisning

Azden mikrofon WL/T-PRO

Läs nedan 📖 manual på svenska för Azden WL/T-PRO (4 sidor) i kategorin mikrofon. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
PRO VHF WIRELESS MICROPHONE SYSTEM
INSTRUCTION MANUAL
WR WM- -PRO -PRO WM/T PRO - - - EX-503 -EX-413
POWER/FREQUENCY
SELECTOR SWITCH
SHOE MOUNT
BATTERY
COMPARTMENT
EARPHONE JACK
SIGNAL INDICATOR
POWER INDICATOR
POWER/FREQUENCY
SELECTOR SWITCH
WR-PRO RECEIVER
WM-PRO TRANSMITTER
EX-503 LAVALIER MIC
MICROPHONE JACK
OUTPUT PLUG
NOTES
Do not store or use the unit in high heat or humidity.
Do not use near a broadcast staon, airport or plane . You must change the frequencies if you are
interfering with other transmiers.
The system will work connuously for 10 hours on one set of baeries. If sound quality is poor,
change baeries.
Remove baeries when the system is not in use.
2
Thank you for purchasing the AZDEN PRO VHF Wireless Microphone System. The following
will show you the contents of the system you ordered:
WHX PRO-
-1 x WR PRO VHF Receiver
-1 x WM/T PRO VHF Transmier/Handheld Microphone
WLX PRO-
-1 x WR PRO VHF Receiver
- -1 x WM PRO VHF Belt Pack Transmier
-1 x EX 503 Lavalier Microphone
WMS PRO-
-1 x WR PRO VHF Receiver
- -1 x WM PRO VHF Belt Pack Transmier
- 1 x EX 413 Wired Handheld Microphone
The PRO systems operate in the low interference VHF band and have 2 switchable frequen--
cies, 169.445 (F1) and 170.245 (F2). You should select the quieter frequency for use.
The systems conforms to Part 90 of the FCC rules. You should contact the FCC oce for l-
ing forms.
WR-PRO RECEIVER
1. Loading Baery
Open the baery compartment lid by sliding it down and raising the lid. Insert a 9-
volt baery into the baery compartment with the correct polarity. Direcons are
on the inside of the baery compartment. Do not force the baery compartment l
id to close. If it does not close easily, turn The baery around and try again.
2. Power/Frequency Selector Switch
This slide switch is used to turn the unit on and o as well as to select a frequency.
When not using the WR PRO, make sure that the switch is turned to OFF. -
3
3. Signal Indicator
This LED has 2 funcons: When you rst turn the Power/Frequency Selector Switch
of the Receiver on, but if the Transmier is not on, the LED will go on and o indi-
cang that the baery is good. If both the Transmier and the Receiver are on and
they are on the same frequency, the Signal Indicator will remain on.
4. Shoe Mount
The Receiver comes with a shoe mount and loop and hook fastener to mount it to a - -
video camera. Select the one works best for your setup. To install the shoe mount,
align the three pegs to corresponding holes and slide the whole assembly upward
unl it clicks. To remove the shoe mount, slide the assembly downward.
5. Output Plug
Connect the plug from the Receiver into the camera’s “EXT. MIC’ jack.
6. Telescopic Antenna
Fully extend the antenna for the best recepon.
7. Earphone Jack
Plug the supplied earphone into the jack to monitor the sound you are recording.
WM/T PRO TRANSMITTER/MICROPHONE-
1. Loading baery
Turn the boom half of the microphone body counterclockwise unl it is completely
o. Insert 1 “AA” baery into the compartment. Make sure the polarity is correct or
the unit will not operate. Replace the boom half and turn it clockwise unl it is
snug. DO NOT OVERTIGHTEN.
2. Frequency Selecon
The unit is factory pre set to F1. Make sure that the Receiver is also set to F1. To -
change to F2, remove the boom half of the microphone body as you did when
loading baery. On the top of the baery compartment, there is a small 2 posion -
switch. Slide the switch to posion F2. Change the Receiver frequency to F2.
3. 3 Posion Power Switch-
The boom posion is “OFF”, the top is “ON”, and the middle is ”STANDBY”. In the
“STANDBY” posion, the unit is on but the microphone is muted. This allows the
microphone to be passed around noiselessly. Remember to set the mic to its “ON”
posion before speaking. When the switch in “ON” or “STANDBY”, the red LED will
stay lit if the Receiver is also operang on the same frequency.

Produktspecifikationer

Varumärke: Azden
Kategori: mikrofon
Modell: WL/T-PRO

Behöver du hjälp?

Om du behöver hjälp med Azden WL/T-PRO ställ en fråga nedan och andra användare kommer att svara dig


mikrofon Azden Manualer

Azden

Azden SGM-250CX Bruksanvisning

6 Oktober 2024
Azden

Azden WMS-PRO Bruksanvisning

15 September 2024
Azden

Azden PRO-XD Bruksanvisning

29 Augusti 2024
Azden

Azden 1201URX/SI Bruksanvisning

29 Augusti 2024
Azden

Azden WDL-PRO Bruksanvisning

24 Augusti 2024
Azden

Azden SMX-10 Bruksanvisning

23 Augusti 2024
Azden

Azden SGM-3500L Bruksanvisning

22 Augusti 2024
Azden

Azden SGM-3416L Bruksanvisning

21 Augusti 2024
Azden

Azden SGM-PII Bruksanvisning

20 Augusti 2024
Azden

Azden 1201XT Bruksanvisning

19 Augusti 2024

mikrofon Manualer

Nyaste mikrofon Manualer

Ambient

Ambient TinyMike ATM216 Bruksanvisning

9 April 2025
Ambient

Ambient Sound Fish ASF-1 MKII Bruksanvisning

9 April 2025
Ambient

Ambient ASF-G Bruksanvisning

9 April 2025
Ambient

Ambient Soundfish 2 MkII Bruksanvisning

9 April 2025
Ambient

Ambient UMP III Bruksanvisning

9 April 2025
Genesis

Genesis Radium 400 G2 Bruksanvisning

8 April 2025
Comica

Comica VP3 Bruksanvisning

2 April 2025
Atlas Sound

Atlas Sound MWHHM Bruksanvisning

2 April 2025
Synco

Synco G2A1 Bruksanvisning

2 April 2025
Synco

Synco PX Bruksanvisning

2 April 2025