Azden WR32-PRO Bruksanvisning

Azden mikrofon WR32-PRO

Läs nedan 📖 manual på svenska för Azden WR32-PRO (3 sidor) i kategorin mikrofon. Denna guide var användbar för 15 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/3
WR32-PRO
DISCRETE DUAL-CHANNEL VHF WIRELESS RECEIVER
Thank you for purchasing an Azden product.
Please read this manual thoroughly before using this
product.
TWO-YEAR LIMITED WARRANTY
AZDEN CORPORATION warrants to the first consumer purchaser that the product purchased is free
from defects in material and workmanship. AZDEN's sole obligation under this warranty shall be to
provide, without charge, repair or replacement (at AZDEN's sole discretion), within two years from the
date of purchase.
This warranty is the sole and exclusive express warranty given with respect to the product and all other
express warranties are hereby excluded. Neither AZDEN nor the dealer who sells the product is
responsible for indirect, incidental, or consequential damages.
This warranty does not extend to any defect, malfunction, or failure caused by misuse, abuse, accident,
or defective associated equipment for which it was not intended. Please read any instructions carefully.
This warranty is valid only when the product is returned directly to AZDEN at the address below, freight
prepaid, together with proof of date of purchase.
200 Valley Road, Suite 101, Mt. Arlington, NJ 07856
Phone: 973-810-3070 Fax: 973-810-3076
e-mail: sales@azdencorp.com www.azdencorp.com
PRINTED IN JAPAN 060-35783-01
PRODUCT DESCRIPTION
The WR32-PRO is a high quality discrete dual-channel VHF receiver which allows you to use two Azden
PRO Series wireless microphone/transmitters simultaneously.
FREQUENCIES
The system operates in the 169 & 172 MHz band, where interference is very low. Before using the system,
it is recommended that you check it at the locaon you are shoong; to make sure that there is no
interference.
LOADING THE BATTERY (see diagram A)
Open the baery door. Load two AA alkaline batteries into the case, making sure that the polarity is correct.
Close the door, but do not force it. If it takes pressure to close, re-check the polarity. The baery life is
approximately 8 hours. Use of rechargeable baeries is not recommended.
SHOE MOUNT (see diagram B)
The WR32-PRO comes with both a shoe mount and hook & loop fastener. You can use either method to
aach the unit to your camera. To use the shoe mount, line up the tabs on the black plasc plate holding
the shoe mount with the holes on the back of the WR32-PRO. Press down gently, and push the tabs upward,
unl you feel them slip into place (reverse the process to remove). Now aach the WR32-PRO to the
camera's shoe stand. Turn the thumbwheel clockwise to ghten, but do not over -ghten. If you're using
the hook & loop fastener instead of the shoe mount, aach the fastener with the smooth surface to the
WR32-PRO, and the piece with the rough surface to the camera.
CABLES & JACKS
The WR32-PRO comes with a stereo mini (3.5mm)-to-stereo mini (3.5mm) cable. Plug one end into the
WR32-PRO's MIC OUT jack, and the other end into the camera's MIC input jack. An oponal stereo“ ”
mini-to-dual XLR cable (part number MX-2) is available for the WR32-PRO.
The PHONE jack on the WR32-PRO is for headphone monitoring only. Plug any stereo headphone into
this jack to monitor sound. The volume level is xed and cannot be adjusted.
ANTENNAS (see diagram C)
For best recepon fully extend the antennas and point them straight up.
For storage lower the antennas and point them straight out from the receiver.
Use cauon, as the antennas are not designed to rotate side to side.
MICROPHONE / TRANSMITTERS
The WR32-PRO works with all Azden microphone/transmiers with the PRO designaon.“ ”
Including the WL/T-PRO and WM/T-PRO or the transmitters from the following systems,
WMS-PRO, WHX-PRO and WLX-PRO.
Consult the manuals for which microphone/transmier come with these systems.
POWER & FREQUENCY ON/OFF SWITCHS (see diagram D)
Turn either the F1 or F2 switch to ON . The corresponding LED will light red, indicang that the power“ ”
is on. Take your PRO Series microphone/transmier and set the frequency selector/switch to the same
frequency you have selected for the WR32-PRO F1 or F2. The corresponding LED on the WR32-PRO will
turn from red to green, indicang that the WR32-PRO is now receiving the signal. If you are using 2
microphone/transmiers with the WR32-PRO, make sure to follow the same procedure for the second unit,
using the other frequency.
CAUTIONS
When two microphone/transmiers are used simultaneously, make sure 1 transmier is set to Frequency
1 (F1) and the other transmitter is set to Frequency 2 (F2). Addionally, when using two microphone/
transmitters, make sure that the transmiers are at least 10 feet (3 meters) away from the WR32-PRO
receiver. Typical operang range is 10-100 feet. Placing one or both transmiers closer than 10 feet
may cause proximity interference problems.
The cable supplied with the WR32-PRO will not work with devices (smart phone, tablet) using a TRRS jack.
An adaptor to convert the WR32-PRO s stereo plug (2 black stripes) to TRRS plug (3 black stripes) will be
necessary.
SPECIFICATIONS
RECEPTION FREQUENCY: F1.169.445MHz
F2.170.245MHz
Double Superheterrodyne System
RECEPTION SENSITIVITY: 2 V at S/N40dBμ
BATTERY: Two 1.5V AA (not included)
POWER CONSUMPTION: 100mA
MONITOR OUTPUT: Voltage: 0.7V
(Load: 30 , Modfreq: 1kHz, Dev: 7kHz)Ω ±
MICROPHONE OUTPUT: Voltage: 25mV
(Load: 10k , Modfreq: 1kHz, Dev: 7kHzΩ ±
Impedance: 300 )Ω
DIMENSIONS: 63(h) X 98(w) X 28.5(d)mm
WEIGHT (including baery):
171g
(B)
(A)
(C)
(D)

Produktspecifikationer

Varumärke: Azden
Kategori: mikrofon
Modell: WR32-PRO

Behöver du hjälp?

Om du behöver hjälp med Azden WR32-PRO ställ en fråga nedan och andra användare kommer att svara dig




mikrofon Azden Manualer

mikrofon Manualer

Nyaste mikrofon Manualer