Best 5810005 Bruksanvisning

Best Fläktkåpa 5810005

Läs nedan 📖 manual på svenska för Best 5810005 (48 sidor) i kategorin Fläktkåpa. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/48

CP34, CP35 AND CP37 SERIES

HB0078

INSTALLATION INSTRUCTIONS

INTENDED FOR DOMESTIC COOKING ONLY

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.

HOMEOWNER: USE AND CARE INFORMATION ON PAGES 12 AND 13.

READ AND SAVE THESE INSTRUCTIONS

BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711

To register your product online or for additional information visit www.BestRangeHoods.com

SV08544 rev. 11

! !

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

qualified personnel in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as

those published by the National Fire Protection Association

(NFPA) and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE) and the local code

authorities.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with any solid-state speed control device.

8. To reduce the risk of fire, use only metal ductwork.

9. This unit must be grounded.

10. When applicable local regulations comprise more

restrictive installation and/or certification requirements,

the aforementioned requirements prevail on those of this

document and the installer agrees to conform to these at his

own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

b) Always turn power pack ON when cooking at high heat or

when flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee,

Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan, filters or in exhaust ducts.

d) Use proper pan size. Always use cookware appropriate for the

size of the surface element.

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Your power pack motor has a thermal overload which will

automatically shut off the motor if it becomes overheated. The

motor will restart when it cools down. If the motor continues to

shut off and restart, have the power pack serviced.

5. The minimum hood distance above cooktop must not be less

than 24”. A maximum of 30” above cooktop is recommended for

best capture of cooking impurities.

6. Two installers are recommended because of the large size and

weight of this unit.

7. To reduce the risk of fire and to properly exhaust air, be sure to

duct air outside — Do not exhaust air into spaces within walls

or ceiling or into attics, crawl space or garage.

8. This product is equipped with a thermostat which may start

blower automatically. To reduce the risk of injury and to prevent

power from being switched on accidentally, switch power off at

service panel and lock or tag service panel.

9. Because of the high exhausting capacity of this unit, you

should make sure enough air is entering the house to replace

exhausted air by opening a window close to or in the kitchen.

10. To reduce the risk of fire and electrical shock, the Best models

CP34, CP35 and CP37 Series should only be installed with

their own built-in blowers. Other blowers cannot be substituted.

11. Please read specification label on product for further

information and requirements.

WARNING

CAUTION

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE

THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels —

This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You own a Class ABC extinguisher and you know how to

operate it.

The fire is small and contained in the area where it started.B.

The fire department has been called.C.

You can fight the fire with your back to an exit.D.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

WARNING

HL0122

- CP34, CP35 AND CP37 POWER PACK SYSTEMS -

M 634 644ODEL OR

(R )OOF CAP

M 643ODEL

(8” R )OUND WALL CAP

M 418 ODEL

(10” R OUND

ADJUSTABLE ELBOW )

M 410 ODEL

(10” R OUND DUCT

— 2 )FT. SECTIONS

10” ROUND VERTICAL

IN LINE DAMPER SUPPLIED WITH- (

DUAL BLOWER POWER PACK )

MODEL 437

(HIGH CAPACITY

ROOF CAP)

MODEL 441

(10’’ ROUND

WALL CAP)

10” ROUND ADAPTER

( SUPPLIED WITH DUAL BLOWER

POWER PACK )

DUAL BLOWER CFM (1200 )

S 48” UPPLIED WITH WIDTH

POWER ONLY PACK

S INGLE BLOWER CFM (600 )

S 30’’, 36’’ UPPLIED WITH AND

42” WIDTH POWER PAC K ONLY

*300 CFM AIR FLOW REDUCER

INTEGRATED ON ODEL CP34 M

CP37

POWER PACK

CP34

POWER PACK*

CP35

POWER PACK

A /DAPTER DAMPER

8” ( ROUND SUPPLIED WITH

SINGLE BLOWER POWER PACKS )

8” ROUND

STANDARD DUCT

8” R OUND

ADJUSTABLE ELBOW

6. REMOVE GREASE DRIP RAIL

A. Lift grease drip rail to disengage it from the bottom

panel.

B. Slide grease rail all the way to the left or right ( ) and 

lift the opposite end to disengage the other end from

the bottom panel (). Remove it from the power pack

and set aside for later use.

7. REMOVE BOTTOM PANEL

Using a Phillips screwdriver, remove both bottom panel retaining

screws and set aside.

8. REMOVE KNOCK-OUT OPENING

From inside the power pack, remove the wiring cover by removing 2 retaining screws and set

aside. Punch out the electrical knockout hole on top of the power pack. Install the wire clamp

(included in parts bag).

9. INSTALL ADAPTER/DAMPER (CP34 AND CP35 MODELS)

Using 4 no. 8 x 3/8” screws from parts bag, assemble the adapter/damper on the top of the power

pack. To ensure proper opening of the dampers, remove shipping tape if present. Seal all joints

with metal foil duct tape to eliminate air leaks.

HD0291

HD0292





Disassemble bottom panel from power pack and set aside.

HO0110

RETAINING SCREW LOCATIONS

HO0111 S IDE VIEW

HR0027

HJ0016

MOUNTING SCREW LOCATIONS

12. REMOVE BLOWER(S)

In order to ease the power pack alignment with existing ductwork, unplug and disassemble the blower(s) from the power pack before

installing the custom hood.

For each blower, using a 5/16” socket, remove all blower mounting screws from the inner top of the

power pack front and rear brackets. Set the screws aside.

HE0085

Unplug the blower(s)

CP34 CP35 MAND ODELS

HD0269

L EFT SIDE MOUNTING

SCREWS LOCATION

Using a 5/16” socket, remove all blower mounting

screws from the inner top of the power pack. Set

the screws aside.

HD0282

R IGHT SIDE

MOUNTING SCREWS

LOCATION

Slide the blower to disengage its flange from the

retaining bracket. Set the blower aside.

HD0270

CP37 MODEL

For each blower, slide it to disengage its flanges from the retaining brackets. Set the blowers aside.

BLOWERS FRONT BRACKET

BLOWERS REAR BRACKET

HD0297

HD0298

14. REINSTALL BLOWER(S) (CONT D’ )

Plug the blower(s) in.

HE0085

A LL MODELS

15. REINSTALL BOTTOM PANEL

Lift the bottom panel and engage the power pack metal tabs in

bottom panel slots, as shown in details and below.A B

Secure the bottom panel to the power pack using its screws

previously removed in step 7.

HO0110

RETAINING SCREW LOCATIONS

A B

HO0112

S IDE VIEW

16. REINSTALL GREASE DRIP RAIL

A. Insert one end of grease rail in power pack side ()

while lifting the other end over the bottom panel

edge ( ).

B. Center the grease drip rail over the bottom panel

edge and flip it to snap in place.

HD0291

HD0292





17. REINSTALL BAFFLE FILTERS

CAUTION

Remove protective plastic film covering filters before installing them.

It is recommended to install side filters first and finish with center one(s).

1. Insert one end of the filter into the upper channel

of the power pack.

2. Raise the other end toward the inside of power

pack and insert in the grease drip rail of the

power pack.

HD0299

18. LIGHT BULBS

This power pack requires shielded halogen lamps (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base), included.

NOTE: Before using lamps, remove shipping tape on them (if present).

1. Install the lamps by placing the bulb leads into their grooves in the socket.

2. Gently push upwards and turn clockwise until secure.

To remove lamps, gently push upwards and turn counterclockwise to disengage bulb leads

from their grooves.

NOTE: To ease removal of the bulbs, use a rubber dishwashing glove or use suction cup

tool available from Best. Contact Best Customer Service at 1-800-558-1711 to order

suction cup tool, part no. 99526707.

WARNING

Do not touch lamps during or soon after operation. Burns may occur. In order to prevent the risk of personal injury,

only install shielded halogen lamps. Also, never install a cool beam, a dichroic lamp, a lamp not suitable for use in

recessed luminaires or identified for use in enclosed fixtures.

1 2

HO0090

Produktspecifikationer

Varumärke:	Best
Kategori:	Fläktkåpa
Modell:	5810005
Färg på produkten:	Wit
Vikt:	2950 g
Bredd:	700 mm
Djup:	700 mm
Höjd:	220 mm
Förpackningens vikt:	5520 g
Förpackningens bredd:	720 mm
Djuppackning:	715 mm
Förpackningshöjd:	230 mm
Husmaterial:	Aluminium, Silicone
siffra:	1
Kompatibilitet:	Mikrotik mANT30