Blaupunkt IRC-S2 Bruksanvisning

Blaupunkt övervakningskamera IRC-S2

Läs nedan 📖 manual på svenska för Blaupunkt IRC-S2 (2 sidor) i kategorin övervakningskamera. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Wireless PIR Camera (IRC-S2)

1. Blue LED /Learn Button

2. IR Sensor

3. LED Flash

T LED Flash delivers sufficient light for image capture in low he

lighting condition .

4. PIR Camera Lens

5. Battery Insula tor

Pull out the insulator to activate battery.

6. Bottom Screw (Tamper Switch)

The Tamper switch protects the PIR Camera from unauthorized

cover opening and is depressed by bottom screw. When the

screw is loosened, the tamper switch will be activate.

PPaacckkaaggee CCoonntteenntt

1 x PIR Camera

4 x wall plugs and screws

2 1.5V AA alkaline batteries (Pre-inserted) x

The PIR Camera can only be learnt into Control Panel within 3

minutes after powering on. If it has been powered on for more

than 3 minutes, remove and reinsert batteries to repower on the

PIR Camera.

1. Put the Control Panel into learning mode l.

2. Press and hold the learn button PIR Camera for 10 on

seconds until both LED Flash and Blue LED flash once, then

release the button to transmi learn code. t a

3. Wait for a short time for PIR Camera to connect to panel. If the

camera is successfully learnt in, the Blue LED will flash twice

to indicate. The panel will also display PIR Camera info. Refer

to panel manual to complete learning.

4. If the PIR Camera and Control do not respond after a short

time (about 20~30 seconds), restart from step 2 to press and

hold the button again.

After learning has been completed, Do press and hold the NOT

learn button for 10 seconds again within 3 minutes after power on,

otherwise the PIR Camera will disconnect from panel and must

be relearnt again.

 T PIR camera designed to be mounted on either a flat surface he

or in a corner with fixing screws and plugs provided.

 The base has knockouts where the plastic is thinner and can be

broken through for mounting. 2 in the center for surface

mounting and 4 on the sides for corner mounting.

1. Remove the cover.

2. For surface mounting, break through the knockouts at t 2 he

center of base.

For corner mounting, break through the 4 knocks on the

corner of PIR camera

3. e the holes as template Us to drill holes in the wall.

4. Insert the wall plugs if fixing it into plaster or brick.

5. Screw the base into the wall plugs.

6. Screw the cover back onto its base.

MMoottiioonn DDeetteeccttiioonn

The PIR Camera is designed to detect movement in protected

area. Upon movement detection, the PIR reports to the Control

Panel for an alarm activation captures 3 images at the same and

time. The images are transferred to the Control Panel to send to

programmed destinations for user to view.

When the Control Panel enters arm mode, or PIR Camera is put

into Test Mode, the PIR Camera will warm up for 30 seconds. Do

not trigger the PIR Camera during the 30 seconds warm up

period. If the PIR Camera is under low battery or tamper opened

condition, the Blue LED will light up during the warm up period.

BBaatttteerryy

The PIR Camera uses two 1.5V AA Alkaline batteries as its power

source. Remove the battery insulator to activate battery. It also

features low battery detection function to notify the Control Panel

when battery voltage is low.

When the PIR camera is low battery, follow the procedure on

below to change the batteries.

1. Open the PIR camera back cover.

2. Remove the old batteries.

3. Press the tamper switch several times to fully discharge.

4. Insert the new batteries and replace the PIR Camera back

cover.

OOppeerraattiioonn

Surface Fixing

Knockouts x 2

Corner Fixing

Knockouts x 4

Battery Saving Guideline

The PIR Camera is wirelessly connected with the Control Panel at

a time. When the PIR Camera loses connection with the Control ll

Panel, it will actively search for the Control Panel, which will

consume extra power and greatly reduces battery life. In order to

avoid unnecessary power consumption, please follow the

guidelines below:

1. Ensure the Control Panel is powered on before removing the

battery insulator. Always learn in the PIR Camera immediately

after activating the battery.

2. Ensure the Control Panel is powered on and within signal

range when the PIR Camera is powered on.

3. When you removed the PIR Camera from the Control Panel,

make sure to remove the batteries from the PIR Camera too.

The test mode function allows you to check the PIR camera’s

detection range. Press and hold the button over 3 seconds, Learn

then release the button to enter the Test mode for 5 minutes.

The PIR Camera will first warm up for 30 seconds, do not trigger

the PIR camera during this warm up period. After the warm up is

complete, you could trigger PIR camera to check its detection

range. PIR camera is triggered, the Blue LED will light up to If

indicate.

For signal range test, please refer to the control panel manual.

Off

Normal Operation

On (2 seconds)

Movement detection under low battery,

tamper triggered condition, or Test mode.

On (30 seconds)

PIR Camera is warming up under low

battery or tamper triggered condition

Flash Rapidly

PIR Camera is transferring image under

low battery or tamper triggered condition.

Flash Once

PIR Camera sends a learn code

Flash Twice

PIR Camera is learnt into Control Panel

Flash every 20

minutes

PIR Camera has lost signal connection

with the Control Panel.

- C to 40 C, relative humidity 85% non-condensing 10° ° .

2.4 GHz

Produktspecifikationer

Varumärke:	Blaupunkt
Kategori:	övervakningskamera
Modell:	IRC-S2
Enhetsplacering:	Vrijstaand
Typ av operation:	Touch
Färg på produkten:	Wit
Dörrgångjärn:	Rechts
Vikt:	66000 g
Bredd:	595 mm
Djup:	693 mm
Höjd:	1746 mm
Nettoskatt:	- W
Barnlås:	Ja
Ljudnivå:	43 dB
Energie-efficiëntieklasse:	E
Årlig-energiförbrukning:	114 kWu
Förpackningens vikt:	74000 g
Förpackningens bredd:	631 mm
Djuppackning:	695 mm
Förpackningshöjd:	1833 mm
Dörröppningsriktning utbytbar:	Ja
Kylskåpets nettokapacitet:	328 l
Kylskåp med bruttokapacitet:	355 l
Kylskåp invändig belysning:	Ja
Typ av lampa:	LED
Antal hyllor i kylskåp:	5
Antal-grönsakslådor:	2
Semesterfunktion:	Ja
Temperaturlarm:	Ja
Äggställ:	Ja
Inget frostsystem:	Ja
Automatisk avfrostning (kylskåp):	Ja
Supercool funktion:	Ja
Kylskåpsdörrfickor:	5
Larm för öppen dörr:	Ja
Klimaatklasse:	SN-ST
Bulleremissionsklass:	D
Justerbara fötter:	Ja
Multi-luftvägssystem:	Ja
Certifiering:	CE\nGS
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 Hz
Energieffektivitetsskala:	A tot G