Caple TSB600WH Bruksanvisning

Caple Fläktkåpa TSB600WH

Läs nedan 📖 manual på svenska för Caple TSB600WH (4 sidor) i kategorin Fläktkåpa. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
Glass splashback
Installation Guide
Please refer to the checklist prior to installation
Contact Caple on 0117 938 1900 or email service@caple.co.uk
Fitting steps – Splashbacks
Fitting steps – Splashbacks
Fitting steps – Splashbacks
Fitting steps – Splashbacks Fitting steps – Splashbacks
Ensure Silicone is used
around enti
enti
enti
entientire
re
re
rere splashback
Do not
not
not
notnot allow Splashback to
rest directly on work surface
– silicone should seal the gap
left by spacers
Assembly guide - Splashbacks
Assembly guide - Splashbacks
Assembly guide - Splashbacks
Assembly guide - Splashbacks Assembly guide - Splashbacks
IMPORTANT
Unfitted glass is fragile. Do not place on hard surfaces prior to fitting. Special care should be taken with
the corners of the product as impact will cause the product to crack.
To prevent product failures ensure that:
All fitting steps are completed.
A space of at least 2mm
A space of at least 2mm
A space of at least 2mm
A space of at least 2mmA space of at least 2mm is left between th
is left between th
is left between th
is left between th is left between the product an
e product an
e product an
e product ane product and all surf
d all surf
d all surf
d all surfd all surfaces.
aces.
aces.
aces. aces.
The gaps must be filled with
The gaps must be filled with
The gaps must be filled with
The gaps must be filled withThe gaps must be filled with silicone
silicone
silicone
silicone silicone.
The surface to which the product is applied is flat, variations in level in excess
of 5mm should be packed with silicone prior to fitting.
You do not use any form of adhesive other than silicone as certain adhesives
will degrade the finish of the glass.
Glass cutting
Glass can be cut by a suitably experienced professional. Specialist glass cutting tools should be used.
Glass must not be cut into pieces of less than 30mm wide neither should less than 30mm be trimmed
from the splash back when cutting to size.
Safe handling of glass
All products are supplied with a safety backing but we recommend that glass is handled with care and in
particular eye protection and suitable gloves should be worn.
After care
Do not use abrasive cleaners. For the best results use:
Hot water with a mild soap detergent.
Before you start
Check that all components are present.
Ensure that you have all tools to hand.
Tools needed to fit the splashback
Tape measure.
Sealant gun.
Silicone sealant - only use low modular neutral cure silicon (BS 5889 A).
2mm tile spacers.
Drilling and cutting should only be undertaken by an
experienced professional with the correct tools.

Produktspecifikationer

Varumärke: Caple
Kategori: Fläktkåpa
Modell: TSB600WH

Behöver du hjälp?

Om du behöver hjälp med Caple TSB600WH ställ en fråga nedan och andra användare kommer att svara dig




Fläktkåpa Caple Manualer

Caple

Caple CE930 Bruksanvisning

22 September 2024
Caple

Caple FGC621 Bruksanvisning

22 September 2024
Caple

Caple DD523BK Bruksanvisning

22 September 2024
Caple

Caple PYR600 Bruksanvisning

22 September 2024
Caple

Caple CGC611 Bruksanvisning

18 September 2024
Caple

Caple DD610BK Bruksanvisning

18 September 2024
Caple

Caple DD820BK Bruksanvisning

18 September 2024
Caple

Caple ATA901 Bruksanvisning

18 September 2024

Fläktkåpa Manualer

Nyaste Fläktkåpa Manualer