Casio G-Shock GN-1000 Bruksanvisning

Casio Titta G-Shock GN-1000

Läs nedan 📖 manual på svenska för Casio G-Shock GN-1000 (17 sidor) i kategorin Titta. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/17

E-7

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City and summer time settings” (page E-34) to conﬁ gure your

Home City and daylight saving time settings.

Important!

• Proper time calibration signal reception and World Time Mode data depend on correct Home City,

time, and date settings in the Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-22).

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually” (page E-36).

The watch is now ready for use.

• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-20).

E-6

Things to check before using the watch

1. Check the battery power level.

Hold down B (page E-2) for at least two seconds to enter the Timekeeping Mode and display the battery

power level.

NO YES

YES

The battery power level will be indicated as

H or M on the left

side of the digital display.

Battery power

indicator

Does any one of the conditions below exist?

• L ﬂ ashing on the digital display.

• “CHARGE” ﬂ ashing on the display.

The watch is charged

sufﬁ ciently.

For details about

charging, see

“Charging the Watch”

(page E-13).

Power is low. Charge the watch by placing it in a location

where it is exposed to light. For details, see “Charging the

Watch” (page E-13). Go to step 2.

• When L is ﬂ ashing, the second hand will jump at two-second intervals.

• When CHARGE is ﬂ ashing, all hands will move to and stop at 12 o’clock.

E-5

Note

• If you do not perform any operation for more than two minutes after pulling out the crown, the indicator

shown below will appear and crown operations will become disabled. If this happens, push the crown

back in and then pull it out again to re-enable crown operations.

• Pulling out the crown while the watch is in a mode that does not allow conﬁ guration of any settings will

cause the indicator shown below to appear. If this happens, push the crown back in and lock it.

• The indicator shown below also appears when performing hand home position adjustment. See “Hand

Home Position Adjustment” (page E-40) for more information.

1 second

• You can use high-speed movement to perform the following operations: when changing a time and/or

date setting; when selecting a city; when performing barometric pressure calibration, magnetic

declination angle calibration, altitude calibration, or temperature calibration operations; when

calibrating high tide times; when setting a latitude and longitude; when conﬁ guring timer settings, when

setting an alarm time

E-4

High-speed Movement

You can use either of the crown operations described below to move watch hands or indicators at high

speed.

HS1: Can be used to move both hands and display indicators.

HS2 (forward only): Can be used when setting the hour and minute manually to move the hands at high

speed.

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly a number of turns away from you

(for forward movement) or towards you (for reverse movement).

To start HS2 high-speed movement (forward only)

While HS1 high-speed forward movement is in progress, rotate the crown

rapidly again a number of turns away from you.

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the current high-speed

movement or press any button.

E-3

Using the Crown

The crown of this watch is a screw in lock crown. Before using the crown,

you must ﬁ rst rotate it towards you to loosen it. After performing crown

operations, be sure to press the crown in lightly as you screw it back in.

Important!

• To maintain water resistance and avoid impact damage to the crown,

be sure to screw it back in when you are not using it.

The illustrations below show the different crown operations.

Pull out Rotate Push in

Crown

Loosen

E-2

About This Manual

• Depending on the model of your watch, digital display text appears

either as dark ﬁ gures on a light background, or light ﬁ gures on a dark

background. All examples in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat

different than depicted by an illustration.

* In the Timekeeping Mode, the small hand indicates tide conditions

(page E-96).

Second hand

Crown

Hour hand Minute hand

Small hand*

E-1

ENGLISH

Important!

• The watch’s Altimeter Mode calculates and displays relative altitude based on barometric pressure

readings produced by its pressure sensor. This means that readings taken at different times at the

same location may produce different altitude values due to changes in barometric pressure. Also note

that the value displayed by the watch may be different from the actual elevation and/or sea level

elevation indicated for the area where you are located.

• When using the watch’s altimeter while mountain climbing, be sure to perform regular calibration in

accordance with the local altitude (elevation) indications. For more information, see “To specify a

reference altitude value” (page E-70).

• Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or other

activities, be sure always to take along another compass to conﬁ rm readings. If the readings produced

by the digital compass of this watch are different from those of the other compass, perform ﬁ gure 8

calibration or 3-point calibration of the digital compass to ensure more accurate readings.

• The Depth Meter Mode of this watch is intended for use while free diving, snorkeling, etc.

• Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of a

permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or

electrical household appliances (TV, computer, cellphone, etc.)

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.

Measured values are then shown on the display. Such features make this watch useful when hiking,

mountain climbing, or when engaging in other such outdoor activities.

Warning !

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered

as reasonable representations only.

•

When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of your watch or its malfunction.

Operation Guide 5477

E-15

Level Battery Power Indicator Function Status

(L)

Auto and manual receive, illumination,

beeper, tide level indication, Tide/Moon

Data Mode functions, Sunrise/Sunset Mode

functions, and sensor operation disabled.

Second hand jumps every two seconds.

(CHARGE)

All hands stopped at 12 o’clock.

All functions disabled.

5 – – –

All hands stopped at 12 o’clock.

All functions disabled and settings returned

to their initial factory defaults.

• The ﬂ ashing L indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

bright light for charging is required as soon as possible.

• Once the battery reaches Level 2 (M) after falling to Level 5, reconﬁ gure the current time, date, and

other settings.

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

E-14

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to go blank (totally black or

totally white, depending on the watch model). The appearance of the LCD should become normal

again when the watch returns to a lower temperature.

• Enable the watch’s Power Saving function (page E-19) and keep it in an area normally exposed to bright

light when storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light

whenever possible.

Power Levels

Hold down B for at least two seconds to enter the Timekeeping Mode.

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Level Battery Power Indicator Function Status

(H) All functions enabled.

(M) All functions enabled.

Battery power

indicator

E-13

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated power charges a

built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed

to light.

Charging Guide

Whenever you are not wearing the

watch, leave it in a location where it

is exposed to light.

• Best charging performance is

achieved by exposing the watch to

the strongest light available.

When wearing the watch, make sure

that its face is not blocked from light

by the sleeve of your clothing.

• The watch may enter a sleep state

(page E-19) if its face is blocked by

your sleeve even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot

when exposed to the conditions below for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

E-12

Using the Alarm …………………………………………………………………………………………… E-108

To enter the Alarm Mode …………………………………………………………………………… E-108

To set an alarm time ………………………………………………………………………………… E-109

To turn an alarm and the Hourly Time Signal on or off ………………………………………… E-110

To stop the alarm tone ……………………………………………………………………………… E-110

To test the alarm tone ……………………………………………………………………………… E-110

Illumination ………………………………………………………………………………………………… E-111

To turn on illumination manually …………………………………………………………………… E-111

To change the illumination duration ……………………………………………………………… E-111

To enable or disable the auto light switch ………………………………………………………… E-113

Other Settings ……………………………………………………………………………………………… E-115

To enable or disable the button operation tone ………………………………………………… E-115

To enable or disable Power Saving ……………………………………………………………… E-115

Troubleshooting …………………………………………………………………………………………… E-116

Speciﬁ cations ……………………………………………………………………………………………… E-125

E-11

Checking the Tide Level and Moon Ages (Tide/Moon) ……………………………………………… E-96

To view the tide level and Moon age for a speciﬁ c date and time ……………………………… E-97

To calibrate the high tide time ……………………………………………………………………… E-99

Looking up Sunrise and Sunset Times ………………………………………………………………… E-101

To enter the Sunrise/Sunset Mode ………………………………………………………………… E-101

To view the sunrise/sunset time for a particular date …………………………………………… E-102

To look up the sunrise and sunset times for a speciﬁ c location ………………………………… E-102

Using the Stopwatch ……………………………………………………………………………………… E-104

To enter the Stopwatch Mode ……………………………………………………………………… E-104

To perform an elapsed time operation …………………………………………………………… E-104

To pause at a split time ……………………………………………………………………………… E-104

To measure two ﬁ nishes …………………………………………………………………………… E-105

Using the Countdown Timer ……………………………………………………………………………… E-106

To enter the Countdown Timer Mode ……………………………………………………………… E-106

To specify the countdown start time ……………………………………………………………… E-106

To perform a countdown timer operation ………………………………………………………… E-107

To stop the alarm …………………………………………………………………………………… E-107

E-10

Using the Altimeter Mode ………………………………………………………………………………… E-66

To specify the altitude reading interval …………………………………………………………… E-67

To take altitude readings …………………………………………………………………………… E-68

To specify a reference altitude value ……………………………………………………………… E-70

To record altitude …………………………………………………………………………………… E-71

To specify the altitude differential measurement range ………………………………………… E-72

To use the altitude differential value ……………………………………………………………… E-73

Precautions Concerning Simultaneous Altitude and Temperature Readings ………………… E-77

Taking Temperature Readings …………………………………………………………………………… E-78

To take temperature readings ……………………………………………………………………… E-78

To calibrate the temperature sensor ……………………………………………………………… E-79

To record the temperature ………………………………………………………………………… E-80

Using the Depth Meter Mode……………………………………………………………………………… E-81

To record depth manually …………………………………………………………………………… E-84

Viewing Recorded Data …………………………………………………………………………………… E-87

To display a data record …………………………………………………………………………… E-87

To delete a speciﬁ c data record …………………………………………………………………… E-91

To delete all data records …………………………………………………………………………… E-91

Checking the Current Time in a Different Time Zone ………………………………………………… E-92

To enter the World Time Mode …………………………………………………………………… E-92

To conﬁ gure World Time City and summer time settings ……………………………………… E-93

To swap your Home City and World Time City …………………………………………………… E-95

To access the UTC (Coordinated Universal Time) time zone ………………………………… E-95

E-9

Hand Home Position Adjustment ……………………………………………………………………… E-40

To trigger hand home position adjustment manually …………………………………………… E-40

Moving the Hands for Easy Viewing of the Digital Display ………………………………………… E-41

To shift the hands and view digital info …………………………………………………………… E-41

To return the hands to their normal positions …………………………………………………… E-42

Specifying Altitude, Depth, Barometric Pressure, and Temperature Units ……………………… E-43

To specify altitude, depth, barometric pressure, and temperature units ……………………… E-43

Taking Barometric Pressure Readings ………………………………………………………………… E-44

To take barometric pressure readings …………………………………………………………… E-44

To specify the barometric pressure auto measurement interval ……………………………… E-47

To toggle barometric pressure differential indication on or off ………………………………… E-47

To enable or disable barometric pressure change indication …………………………………… E-51

To calibrate the pressure sensor …………………………………………………………………… E-52

To record the barometric pressure ………………………………………………………………… E-53

Taking Direction Readings ……………………………………………………………………………… E-54

To take a direction reading ………………………………………………………………………… E-55

To perform ﬁ gure 8 calibration ……………………………………………………………………… E-58

To perform 3-point calibration ……………………………………………………………………… E-60

To perform magnetic declination correction ……………………………………………………… E-63

To record the bearing to an objective ……………………………………………………………… E-64

E-8

Contents

About This Manual …………………………………………………………………………………………… E-2

Using the Crown ……………………………………………………………………………………………… E-3

Things to check before using the watch ………………………………………………………………… E-6

Charging the Watch ………………………………………………………………………………………… E-13

To recover from the sleep state …………………………………………………………………… E-19

Radio Controlled Atomic Timekeeping ………………………………………………………………… E-20

To get ready for a receive operation ……………………………………………………………… E-22

To perform manual receive ………………………………………………………………………… E-24

To check the latest signal reception results ……………………………………………………… E-26

To enable or disable auto receive ………………………………………………………………… E-26

Mode Reference Guide …………………………………………………………………………………… E-28

Timekeeping ………………………………………………………………………………………………… E-33

Conﬁ guring Home City Settings ………………………………………………………………………… E-34

To conﬁ gure Home City and summer time settings ……………………………………………… E-34

Conﬁ guring Current Time and Date Settings Manually ……………………………………………… E-36

To change the current time and date settings manually ………………………………………… E-36

To switch between 12-hour and 24-hour timekeeping …………………………………………… E-38

To record the date and time ………………………………………………………………………… E-39

Operation Guide 5477

E-23

• Signal reception may be difﬁ cult or even impossible under the conditions described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁ ce

equipment,

or a mobile

phone

Near a

construction

site, airport

Near

high-tension

power lines

Among or

behind

mountains

3. What you should do next depends on whether you are using auto receive or manual receive.

• Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”

be low for details.

• Manual receive: Perform the operation under “To perform manual receive” on page E-24.

Auto Receive

• With auto receive, the watch performs the receive operation each day automatically up to six times (up

to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to

the Timekeeping Mode time). When any receive operation is successful, none of the other receive

operations for that day are performed.

• When a calibration time is reached, the watch will perform the receive operation only if it is in the

Timekeeping Mode. The receive operation is not performed if a calibration time is reached while you

are conﬁ guring settings.

E-22

• Even when the watch is within range of a transmitter, signal reception may be impossible due to the

effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,

etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the

inﬂ uence of the conditions listed above becomes even greater.

• Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 500 kilometers (310 miles)

• As of January 2016, China does not use Daylight Saving Time (DST). If China does go to the Daylight

Saving Time system in the future, some functions of this watch may no longer operate correctly.

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode. If it isn’t, use B to enter the Timekeeping Mode

(page E-30).

2. The antenna of this watch is located on its 7 o’clock side. Position the watch with 7 o’clock facing

towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.

• Signal reception normally is better at night.

• The receive operation takes from two to ten minutes, but

in some cases it can take as long as 20 minutes. Take

care that you do not perform any button operation or

move the watch during this time.

7 o’clock

E-21

Approximate Reception Ranges

UK and German Signals

Japanese Signals Chinese Signal

North American Signal

Anthorn

Mainﬂ ingen

Fukushima

500 kilometers

Fukuoka/Saga

1,000 kilometers

500 kilometers Changchun

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

1,500 kilometers

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

For the Honolulu and Anchorage time zones, the

signal can be received when reception conditions

are favorable.

500 kilometers

1,500 kilometers

The Anthorn signal is

receivable within this area

E-20

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. However, when

using the watch outside of areas covered by time calibration signals, you will have to adjust the settings

manually as required. See “Conﬁ guring Current Time and Date Settings Manually” (page E-36) for more

information.

This section explains how the watch updates its time settings automatically when the city code selected

as the Home City is in Japan, North America, Europe, or China, and is one that supports time calibration

signal reception.

If your Home City Code setting is this: The watch can receive the signal from the transmitter

located here:

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW Anthorn (England), Mainﬂ ingen (Germany)

HKG, BJS Shangqiu City (China)

TPE, SEL, TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ,

YYT Fort Collins, Colorado (United States)

Important!

• The areas covered by MOW, HNL and ANC are quite far from the calibration signal transmitters, so

certain conditions may cause reception problems.

• When

HKG or BJS is selected as the Home City, only the time and date are adjusted according to the

time calibration signal. You need to switch manually between standard time and daylight saving time

(DST) if required. See “To conﬁ gure Home City and summer time settings” (page E-34) for information

about how to do this.

E-19

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain

period in an area where it is dark. The table below shows how watch functions are affected by Power

Saving.

• For information about enabling and disabling power saving, see “To enable or disable Power Saving”

(page E-115).

• There actually are two sleep state levels: “display sleep” and “function sleep”.

Elapsed Time in Dark Hands and Display Operation

60 to 70 minutes (display sleep) Blank display, second hand

stopped.

Except for display and second hand, all

functions enabled.

6 or 7 days (function sleep) Blank display, all hands

stopped at 12 o’clock.

Except for timekeeping, all functions

disabled.

• The watch will not enter a sleep state between 6:00 a.m. and 9:59 p.m.. If the watch is already in a

sleep state when 6:00 a.m. arrives, however, it will remain in the sleep state.

• The watch will not enter a sleep state while it is in the World Time Mode, Stopwatch Mode or

Countdown Timer Mode.

• The watch will not enter a sleep state while the barometric pressure change indicator is enabled (page

E-49).

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page

E-112).

E-18

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 5 Level 4 Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 min. 2 hours 20 hours 6 hours

Sunlight through a window (10,000 lux)

30 min. 6 hours 74 hours 20 hours

Daylight through a window on a

cloudy day (5,000 lux) 48 min. 9 hours 120 hours 32 hours

Indoor ﬂ uorescent lighting (500 lux) 8 hours 103 hours – – – – – –

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations (page E-129).

E-17

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause the

recovery indicator (RECOVER) to start ﬂ ashing on the display. This indicates that the watch is in the

power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and sensor

operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the recovery indicator (

RECOVER) will stop

ﬂ ashing. This indicates that the functions listed above are enabled again.

• Frequent ﬂ ashing of the recovery indicator (RECOVER) indicates that battery power is low. Expose the

watch to bright light as soon as possible.

• Even if battery power is at Level 1 (

H) or Level 2 (M), sensor measurement may be disabled, and Tide/

Moon Data Mode and Sunrise/Sunset Mode access may not be possible if there is not enough power

available to power it sufﬁ ciently. This is indicated when the recovery indicator (RECOVER

) is ﬂ ashing.

• Frequent ﬂ ashing of the recovery indicator (RECOVER) probably means that remaining battery power

is low. Leave the watch in bright light to allow it to charge.

E-16

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The

correct battery level should be indicated after a few minutes.

• All data stored in memory is deleted, and the current time and all other settings return to their initial

factory defaults whenever battery power drops to Level 5 and when you have the battery replaced.

A dark environment while battery power is at Level 4 will cause the level to drop to Level 5. Expose the

watch to bright light whenever possible.

Low battery alert

When battery power reaches Level 3, the second hand of the watch will

jump at 2-second intervals in the Timekeeping Mode to let you know that

charging is required.

Jumps at two-second

intervals

Operation Guide 5477

Produktspecifikationer

Varumärke:	Casio
Kategori:	Titta
Modell:	G-Shock GN-1000

Behöver du hjälp?

Om du behöver hjälp med Casio G-Shock GN-1000 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Titta Casio Manualer

Casio Edifice EQB-1000TR-2AER Bruksanvisning

24 Oktober 2024

Casio Collection MTP-1259PD-7BEF Bruksanvisning

24 Oktober 2024

Casio G-Shock GA-810B-1A9ER Bruksanvisning

24 Oktober 2024

Casio Collection SGW-450HD-1BER Bruksanvisning

24 Oktober 2024

Casio Edifice EQB-1000XD-1AER Bruksanvisning

24 Oktober 2024

Casio Collection MTP-1222A-2AVEF Bruksanvisning

24 Oktober 2024

Casio G-Shock GMW-B5000G-2ER Bruksanvisning

24 Oktober 2024

Casio Radio Controlled WV-200E-1AVEF Bruksanvisning

24 Oktober 2024

Casio Collection LWS-2000H-2AVEF Bruksanvisning

24 Oktober 2024

Casio Pro Trek PRW-60YBM-1AER Bruksanvisning

24 Oktober 2024

Titta Manualer

Nyaste Titta Manualer

Lorus W207 Bruksanvisning

27 Oktober 2024

Invicta Specialty 31308 Bruksanvisning

27 Oktober 2024

Timex Ironman TW5M244009J Bruksanvisning

26 Oktober 2024

Timex MK1 TW2R68800VQ Bruksanvisning

26 Oktober 2024

Braun BN0021 Bruksanvisning

24 Oktober 2024

Braun AW60 Bruksanvisning

24 Oktober 2024

Braun BN0042 Bruksanvisning

24 Oktober 2024

Skmei 0984A Bruksanvisning

22 Oktober 2024

Suunto SPARTAN ULTRA 1.2 Bruksanvisning

21 Oktober 2024

Skmei 0955 Bruksanvisning

21 Oktober 2024