Casio W-212HD-1AVEF Bruksanvisning

Casio Titta W-212HD-1AVEF

Läs nedan 📖 manual på svenska för Casio W-212HD-1AVEF (2 sidor) i kategorin Titta. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
1
Operation Guide 3149
4. While a setting is flashing, press D to increase it.
To set an alarm that does not include a month (Daily alarm, Monthly alarm),
set x for the month. Press D until the x mark appears (between 12 and 1) while
month setting is flashing.
To set an alarm that does not include a day (Daily alarm, 1-Month alarm),
set xx for the day. Press D until the
xx mark appears (between the end of the
month and 1) while the day setting is flashing.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, or
until you turn the alarm off or change it to a one-time alarm.
Note
Pressing any button stops the alarm tone operation.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm
1
setting screen
To test the alarm
In the Alarm Mode, hold down to sound the alarm.D
To turn Alarms
2
through
5
on and off
1. In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 through 5).
2. Press A to toggle the displayed alarm on and off.
Turning on a one-time alarm (
2 through 5) displays the
one-time alarm on indicator on its screen.
The one-time alarm on indicator is displayed in all
modes.
If any alarm is on, the one-time alarm on indicator is
shown on the display in all modes.
To select the operation of Alarm
1
1. In the Alarm Mode, use D to select Alarm
1.
2. Press A to cycle through the available settings in the sequence shown below.
Snooze alarm on indicator and one-time alarm on indicator
One-time alarm on Alarm offSnooze alarm on
The applicable indicator is displayed in all modes when an alarm is turned on.
The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
Displaying the Alarm1 setting screen while the snooze alarm is turned on turns off
the snooze alarm automatically (making Alarm
1 a one-time alarm).
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
You can configure Alarm1 as a snooze alarm or a one-time alarm. Alarms
2
through 5 can be used as one-time alarms only.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
Hour Minutes Month Day
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
You also can turn on an hourly time signal that causes the
watch to beep twice every hour on the hour.
There are five alarm screens numbered
1 through 5.
The hourly time signal screen is indicated by
:00.
When you enter the Alarm Mode, the screen you were
viewing when you last exited the mode appears first.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Alarm Types
The alarm type is determined by the settings you make, as described below.
Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at time you set, only during the month you set.
Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at time you set, on the day you set.
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds Hour Minutes
Day Month Year
3. When the setting you want to change is flashing, press D to change it as
described below.
MA0804-EA
About This Manual
Button operations are indicated using the letters shown
in the illustration.
Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Timekeeping Mode Alarm Mode Countdown Timer Mode Stopwatch Mode Dual Time Mode
Press .
General Guide
Press C to change from mode to mode.
In any mode, press B to illuminate the display.
In any mode, hold down for about two seconds to return to the TimekeepingC
Mode.
Hour : Minutes Seconds
Day of week
PM indicator
Month – Day
To change this setting
Seconds
Hour, Minutes, Year, Month, Day
Perform this button operation
Press .D to reset to 00
Press D to increase the setting.
Pressing while the seconds are in the range of 30 to 59 resets them to andD00
adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.
4. Press A to exit the setting screen.
The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
The year can be set in the range of 2000 to 2099.
The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after you have the watch’s battery replaced.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press to toggle between 12-hour timekeeping andD
24-hour timekeeping.
With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Hour : Minutes
One-time alarm on
indicator
2
Operation Guide 3149
Illumination
An LED (light-emitting diode) illuminate the display for
easy reading in the dark.
Illumination Precautions
Illumination may be hard to see when viewed under
direct sunlight.
Illumination turns off automatically whenever an alarm
sounds.
Frequent use of illumination runs down the battery.
To illuminate the display
Press B to turn on illumination.
Dual Time
The Dual Time Mode lets you keep track of time in a different time zone.
In the Dual Time Mode, the seconds count is synchronized with the seconds count
of the Timekeeping Mode.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. In the Dual Time Mode, hold down A until the hour
setting starts to flash, which indicates the setting
screen.
3. Press C to change the selection in the following
sequence.
Hour Minutes
4. Press D to increase the setting.
5. Press A to exit the setting screen.
Countdown Timer
The countdown timer can be set within a range of
1 minute to 24 hours. An alarm sounds when the
countdown reaches zero.
You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
Countdown timer functions are available in the
Countdown Timer Mode, which you enter by pressing
C.
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
To completely stop a countdown operation, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
To set the countdown start time
1. In the Countdown Timer Mode, hold down A until the
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press C to move the flashing between the hours and
minutes settings.
3. While a setting is flashing, use D to change it.
To set the starting value of the countdown time to
24 hours, set 0:00.
4. Press A to exit the setting screen.
To turn auto-repeat on and off
1. In the Countdown Timer Mode, hold down A until the
hours setting of the countdown start time starts to flash,
which indicates the setting screen.
2. Press B to toggle auto-repeat on (
AUTO REPEAT
displayed) and off (
AUTO REPEAT
not displayed).
Note that pressing B in the above operation also turns
on the illumination.
When the end of the countdown is reached while
auto-repeat is on, the alarm sounds, but the countdown
restarts from the beginning without stopping. You can
stop the countdown by pressing and manually resetD
to the start time by pressing A.
The auto-repeat indicator appears in the Countdown
Timer Mode only.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing .C
To measure times with the stopwatch
Elapsed time
Start Stop Re-start Stop Clear
Start Split
( displayed)SPL
Split release Stop Clear
Start Split Stop Split release Clear
Split time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
To turn the hourly time signal on and off
1. In the Alarm Mode, use D to select the hourly time
signal (:00).
2. Press A to toggle it on and off.
Turning on the hourly time signal displays the hourly
time signal on indicator.
The hourly time signal on indicator is displayed in all
modes when the hourly time signal is turned on.
Hour
Minutes
Seconds
Hourly time signal on
indicator
Auto-repeat indicator
1/100 second
Hour
Minutes
Seconds
Hour : Minutes Seconds
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto return features
If you leave a screen with flashing digits for two or three minutes without performing
any operation, the watch automatically saves any settings you have made up to that
point and exits the setting screen.
Data and Setting Scrolling
The D button is used to scroll through setting screen data on the display. Holding
down this button during a scroll operation scrolls through the data at high speed.

Produktspecifikationer

Varumärke: Casio
Kategori: Titta
Modell: W-212HD-1AVEF

Behöver du hjälp?

Om du behöver hjälp med Casio W-212HD-1AVEF ställ en fråga nedan och andra användare kommer att svara dig




Titta Casio Manualer

Titta Manualer

Nyaste Titta Manualer