Chief MTR6000 Bruksanvisning

Chief Platt panelstöd MTR6000

Läs nedan 📖 manual på svenska för Chief MTR6000 (8 sidor) i kategorin Platt panelstöd. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

Chief Manufacturing, a products division of

Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

P: 800.582.6480 / 952.894.6280 F: 877.894.6918 / 952.894.6918

8805-000215 Rev 01

A Duchossois Group Company

02/09

I N S T A LL A T IO N IN S T R U C T IO N S

MEDIUM FLAT PANEL DISPLAY TILT MOUNT

MTR Series

The MTR Series tilt mount accommodates medium flat

panel displays weighing up to 125 lbs (56.70kgs).

The teardrop holes in the mount allow for quick

connect/disconnect of the display, thus simplifying

installation and maintenance processes.

The top and bottom mounting brackets are adaptable to

single wood stud mounting or dual wood studs that are

16” on center.

The display can be pulled and tilted into any position in

the zero-to-15 degree tilt range and remain stationary.

When fully retracted, the mount depth is 1.56 inches.

After installing the display on the mount, the screen can

be locked in place using the convenient latching ﬂag.

A padlock can be used on the latching ﬂag for added

security.

The mount is concealed behind the display, making it a

low profile wall mount.

! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval

documents and drawings before beginning installation. OSHPD documents and drawings are available at

www.chiefmfg.com, and located on the product information page for the mount.

BEFORE YOU BEGIN

CAUTION: To prevent damage to your monitor and MTR, which could aﬀect or void the Factory

warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay

particular attention to the Warnings and Cautions in this document.

The mount is designed to be installed using wall studs or supporting framework. The fasteners used to anchor the

mount must be capable of supporting five times the total weight of the equipment.

The maximum weight to be installed on the MTR Series tilt wall mount is 125 lbs (56.70kg).

If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-6280.

Installation Instructions MTR Series

IMPORTANT WARNINGS and CAUTIONS!

WARNING A WARNING alerts you to the possibility of serious injury or death if you do not

follow the instructions.

CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do

not follow the corresponding instructions.

WARNING Improper installation can result in serious personal injury! Make sure that the

structural members can support a redundant weight factor five times the total weight

of the equipment. If not, reinforce the structure before installing the MTR

WARNING Be aware of the potential for personal injury or damage to the equipment if it is not

installed correctly. Consider the weight of the mount without the display.

WARNING The installer is responsible for verifying that the display to which the wall mount is

fastened will safely support the combined load of all attached components or other

equipment.

WARNING The combined weight of the display placed on the wall mount must not exceed 125 lbs

(56.70 Kg),the maximum support weight of the MTR.

WARNING Watch for pinch points. Do not put your ﬁngers between movable parts.

WARNING Make sure the flag securing the display is completely lowered at all times except when

removing or installing the display. The flag must be all the way down when

installing/removing cables.

CAUTION Check the unit for shipping damage before you begin the installation.

DIMENSIONAL DRAWING

Installation Instructions MTR Series

CONTENTS

DIMENSIONAL DRAWING ..................................... 2

TOOLS REQUIRED FOR INSTALLATION.............. 3

PARTS LIST .............................................................. 3

MTR INSTALLATION .............................................. 4

Select Mounting Location........................................ 4

Mount the MTR....................................................... 5

ATTACH MSB TO THE DISPLAY ........................... 6

INSTALL THE DISPLAY.......................................... 6

TILT ADJUSTMENT ................................................. 7

REMOVE THE DISPLAY.......................................... 7

TOOLS REQUIRED FOR

INSTALLATION

Drill and drill bit set

Wrench set

NOTE: Other tools may be required depending on your

method of installation.

Figure 1. Parts

PARTS LIST

Prior to assembly, unpack the carton completely. Verify

contents listed in Table 1 and Figure 1.

Read installation instructions completely. If you are

missing any of the listed parts, contact Customer Service.

Table 1. Parts List

REF DESCRIPTION QTY

10 MTR-Series Tilt Mount 1

— Lag Bolts 4

— Flat Washers 4

4 Lag Bolts

4 Washers

Produktspecifikationer

Varumärke:	Chief
Kategori:	Platt panelstöd
Modell:	MTR6000
Färg på produkten:	Zilver
Vikt:	3000 g
Bredd:	130 mm
Djup:	251 mm
Höjd:	90.9 mm
Förpackningens bredd:	303 mm
Djuppackning:	226 mm
Förpackningshöjd:	173 mm
Medföljande kablar:	USB Type-C
Monteringsalternativ för kabellås:	Ja
Kabellåsspårtyp:	Kensington
USB-anslutning:	Nee
Internera:	Nee
Stöder Mac-operativsystem:	Mac OS X 10.12 Sierra
Mac-kompatibilitet:	Ja
Lagringsenheter installerade:	Ja
Installerad lagringsenhet:	HDD
Total installerad lagringskapacitet:	24 TB
Maximal lagringskapacitet som stöds:	24 TB
Antal lagringsenheter installerade:	2
HDD rotationshastighet:	7200 RPM
Gränssnitt för lagringsdisk:	SATA III
Typer av RAID:	0, 1,JBOD
Antal lagringsenheter som stöds:	2
Thunderbolt-teknik:	Ja
Typer av lagringsenheter som stöds:	HDD
Värdportar:	2
Thunderbolt version:	3