Chief SLM208 Bruksanvisning

Läs nedan 📖 manual på svenska för Chief SLM208 (1 sidor) i kategorin Projektor tillbehör. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000274
10/18/07
SLB-208 and SLM-208 Interface Brackets
for BENQ SP830, SP831
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector lining up the four holes in the bracket with the four threaded inserts in the bottom
of the projector.
4. Using the four M4 X 10mm mounting screws and washers, start them into the mounting holes by hand and secure all four fasteners at this
time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (4) WASHER, Flat, M4
(4) 10-24 Thumb Nuts ** (4) SCREW, Pan Head, M4 x 10mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-208
SLM-208
Towards front of Towards front of
Projector
Projector

Produktspecifikationer

Varumärke: Chief
Kategori: Projektor tillbehör
Modell: SLM208

Behöver du hjälp?

Om du behöver hjälp med Chief SLM208 ställ en fråga nedan och andra användare kommer att svara dig




Projektor tillbehör Chief Manualer

Chief

Chief CHCMS115 Bruksanvisning

19 September 2024
Chief

Chief SSM019 Bruksanvisning

9 September 2024
Chief

Chief SLM220 Bruksanvisning

9 September 2024
Chief

Chief SSB164 Bruksanvisning

9 September 2024
Chief

Chief SSM231 Bruksanvisning

9 September 2024
Chief

Chief SLM208 Bruksanvisning

9 September 2024
Chief

Chief SSM126 Bruksanvisning

9 September 2024
Chief

Chief SLM500 Bruksanvisning

9 September 2024
Chief

Chief SSM8000 Bruksanvisning

9 September 2024
Chief

Chief CPA261 Bruksanvisning

9 September 2024

Projektor tillbehör Manualer

Nyaste Projektor tillbehör Manualer