Chief SSB138 Bruksanvisning

Chief Projektor tillbehör SSB138

Läs nedan 📖 manual på svenska för Chief SSB138 (1 sidor) i kategorin Projektor tillbehör. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000211 Rev01

a Duchossois Group Company

05/09

SSB-138, SSM-138, SLB-138 and SLM-138 Interface Brackets

SSB-138, SSM-138, SLB-138 and SLM-138 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place a felt pad around the bail on each end to protect the paint on the projector.

4. Place the bail around the top surface of the projector so the threads are pointed toward the bottom of the projector and the threads are in

the front and back of the projector.

5. Place the interface bracket onto the bottom of the projector so the tabs are on the back and on the sides of the rear rubber feet on the

projector, and the threaded bail threads align and go through the holes in the interface bracket.

6. Using the #10 washers and Nylock nuts, secure interface bracket to projector and tighten all fasteners at this time.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation

instructions in the All-Points Security Kit.

(1) Interface Bracket (2) Security Plates

(4) 10 - 24 Thumb Nuts** (2) #10 Flat washers

(1) All-Points Security Kit (2) 10 – 24 Nylock Nuts

(1) U-Form Bail (4) 1” Felt Pads Square

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style

interface bracket installation.

(

)

(

)

SLM-138

SLB-138

Towards front of

projector

Towards front of

projector

Produktspecifikationer

Varumärke:	Chief
Kategori:	Projektor tillbehör
Modell:	SSB138
Vikt:	188 g
Bredd:	86.36 mm
Batterikapacitet:	150 mAh
Frekvensband:	2.4 GHz
Batteriteknik:	Nikkel-Metaalhydride (NiMH)