Chief SSB8010 Bruksanvisning

Läs nedan 📖 manual på svenska för Chief SSB8010 (1 sidor) i kategorin Projektor tillbehör. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 F:877.894.6918 / 952.894.6918
8850-000218 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-8010, SSM-8010, SLB-8010 and SLM-8010 Interface Brackets
SSB-8010, SSM-8010, SLB-8010 and SLM-8010 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the
specific installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10 - 24 x 5/8” Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the three nylon spacers onto the three threaded inserts in the bottom of the projector.
4. Place the interface bracket onto the three nylon spacers on the bottom of the projector, and align the three mounting holes in the bracket
with the three nylon spacers.
5. Using the three M6 x 12mm screws, secure interface bracket to projector and tighten all fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) M6 x 12mm Phillips Pan Screws
(4) 10 - 24 Thumb Nuts** (3) 1/2” x .320 x 1/4” Nylon Spacers
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-8010
SLM-8010
(Note: SSM-style interface bracket connection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSB-style interface bracket connections
a
r
e
c
r
Towards front of
projector
Towards front of
projector

Produktspecifikationer

Varumärke: Chief
Kategori: Projektor tillbehör
Modell: SSB8010

Behöver du hjälp?

Om du behöver hjälp med Chief SSB8010 ställ en fråga nedan och andra användare kommer att svara dig




Projektor tillbehör Chief Manualer

Projektor tillbehör Manualer

Nyaste Projektor tillbehör Manualer