Crestron CLXI-1DIM4 Bruksanvisning

Crestron Inte kategoriserad CLXI-1DIM4

Läs nedan 📖 manual på svenska för Crestron CLXI-1DIM4 (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/6

CLTI- & CLXI-1DIM4

Terminal Block & Module Locations (Single-wide Enclosure)

Functional Summary

GROUNDING

TERMINAL

BLOCK

TERMINAL

BLOCK

MODULE

(INSTALL INTO

LOWEST

AVAILABLE

SPACES)

The Crestron 1-Feed, 4-Dimmer Terminal Block and

Module (CLTI-1DIM4 and CLXI-1DIM4, respectively),

are considered a single entity and must be used together.

They ship separately to permit termination of the field

wiring to the CLTI-1DIM4 prior to installation of the

CLXI-1DIM4, as described in this guide. They can be

mounted in any Crestron Automation Enclosure (CAEN

or CAENIB-Series Enclosures). The terminal block is

designed to terminate the circuit feed (LINE and

NEUTRAL) and distribute the controlled circuit (LOAD)

to the fixtures. The module connects to the terminal block

and performs dimming control of four incandescent,

magnetic low voltage, neon, cold cathode, or dimmable

2-wire fluorescent lighting loads. The maximum load is

10 amps for any controlled circuit, limited to 13 amps

total per module. The unit requires 230VAC 50 Hz,

1 phase input voltage. An oversize heat sink dissipates

heat efficiently. There are LEDs on the module to indicate

communication to a Cresnet network, input power to the

module, and output power to the load.

NOTE: When connecting to an Arc Fault Breaker, the

load should not exceed 1000 watts. Terminal Block & Module Locations (Double-wide Enclosure)

TERMINAL BLOCK

(RIGHT)

GROUNDING TERMINAL BLOCKS

TERMINAL BLOCK

(LEFT)

MODULE

(INSTALL INTO

LOWEST

AVAILABLE

SPACES)

Installation

Terminal block and module must be mounted into a

Crestron Automation Enclosure by a licensed electrician,

in accordance with all national and local codes.

CAUTION: This equipment is for indoor use only and

needs to be air-cooled. Mount in a well-ventilated area.

The ambient temperature must be 0°C to 40°C (32°F to

104°F). The relative humidity must be 0% to 90% (non-

condensing).

Terminal blocks are installed along the left side of single-

wide enclosures and along the outside edges (left and

right sides) of double-wide enclosures. Modules are

installed along the right side of single-wide enclosures

and side-by-side in the center of double-wide enclosures.

When installing modules and terminal blocks in a double-

wide enclosure, be sure to invert units on the right side so

that they can be properly wired. Refer to the illustrations

shown below when considering the location of terminal

blocks and modules within an enclosure.

NOTE: Modules and terminal blocks must be installed

into the lowest available spaces and continue toward the

top of the enclosure.

Crestron Electronics, Inc. Installation Guide – DOC. 6406A

15 Volvo Drive Rockleigh, NJ 07647 (2013814)

Tel: 888.CRESTRON 11.07

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Terminal Block & Module Crestron CLTI- & CLXI-1DIM4

2 – • Terminal Block & Module: CLTI- - & CLXI 1DIM4 Installation Guide DOC. 6406A

Terminal Block Installation and Field

Wiring

NOTE: To install a CLTIBN Circuit Breaker Terminal

Block, refer to the latest version of the CLTIBN

Installation Guide (Doc. 6561) which can be downloaded

from the Crestron website (www.crestron.com/manuals).

NOTE: Both left- -side and right side adhesive wiring

labels are provided. The left-side labels are used in both

single and double- -wide enclosures. The right side labels

are only used in double-wide enclosures.

1. Remove the backing from the left or right

adhesive wiring label.

2. Apply the adhesive label by aligning the holes in

the label with the appropriate holes on the

Crestron Automation Enclosure where the

terminal block is to be mounted. For information

on mounting locations, refer to the latest version

of the CAEN Installation Guide (Doc. 5940) or

the CAENIB Installation Guide (Doc. 6562). The

wiring label lies beneath the terminal block as

shown in the two wiring diagrams on this page.

3. Use the two supplied self-tapping pan Phillips

screws (8B x ¼ (6 mm) length) to secure the

terminal block to the Crestron Automation

Enclosure.

CAUTION: A bypass jumper is provided to allow

testing and to protect the module during installation.

When properly secured by five screws, the bypass

jumper on the brown and red section of the terminal

block shorts the LINE in to DIM out so that the

circuit is energized. Do not remove the bypass

jumper until all feed and load wiring has been

completed, the circuit has been tested for electrical

faults, and the module has been installed. Refer to

“Module Installation” on next page.

Furthermore, the jumper on the blue section of the

terminal block ties the neutral in to the neutral outs.

This jumper should never be removed.

NOTE: Use copper conductors only – rated 75°C

4. With the circuit breakers turned off, connect the

circuit feed (LINE and NEUTRAL) and

controlled circuit (LOAD) wires to the terminal

block per the markings provided on the wiring

label (as shown in the diagrams on this page).

Terminal blocks accept one 2.5 - 6.0 mm

2 wire.

Wires should be stripped to 12 mm. Tighten

terminal blocks to 1 Nm.

5. Grounding terminal blocks are available in the

cabinet for termination of ground wires. Tighten

to 4 Nm (2.5 - 6.0 mm2), 4.5 Nm (10.0 mm2), or

5.1 Nm (16 - 25 mm2).

6. Test the circuit for electrical faults by turning on

the circuit breaker, checking that the breaker

does not trip, and that power is delivered to the

proper loads.

NOTE: If installing in a CAENIB, complete the

installation with a CAENIB-BP Blank Plate. Refer to the

latest version of the CAENIB-BP Installation Guide (Doc.

6563) for details.

Wiring Diagram of the Terminal Block to the Feed and

Load(s)(Single- -wide and Left Side Double wide Enclosures)

TERMINAL

BLOCK

GROUNDING

TERMINAL

BLOCK

GND

LEFT SIDE

WIRING LABEL

LOAD(S)

AREA FOR

MODULE

LOCATION

LABEL

(FROM 16 AMP

CIRCUIT BREAKER)

NEUTRAL

LINE

BYPASS

JUMPER

Wiring Diagram of the Terminal Block to the Feed and

Load(s) (Right Side Double-wide Enclosures)

TERMINAL

BLOCK

RIGHT SIDE

WIRING LABEL

BYPASS

JUMPER

NEUTRAL

(FROM 16 AMP

CIRCUIT

BREAKER)

AREA FOR

MODULE

LOCATION

LABEL

LOAD(S)

GROUNDING

TERMINAL

BLOCK

LINE

GND

Crestron CLTI- - & CLXI 1DIM4 Terminal Block & Module

Installation Guide – 3 DOC. 6406A Terminal Block & Module: CLTI- - & CLXI 1DIM4 •

Module Installation

CAUTION: Module contains electrostatic sensitive

devices (ESDs); unit must be handled from metal chassis

– do not touch PC board or components.

NOTE: Modules are to be installed after enclosure has

been completely wired. Refer to the terminal block

installation procedure on page 2 for details.

1. Use the four supplied self-tapping pan Phillips

screws (8B x ¼-inch (6 mm) length) to secure

the module to the enclosure.

2. As shown in the wiring diagrams (next column),

connect the wires from the module to the

terminal block. Each wire exits the module

directly in line with, and is the same color as, the

terminal to which it should be connected. Wires

are pre-stripped to 12 mm. Tighten to 1 Nm.

3. If the module is being installed above another

module within the enclosure, attach the supplied

module interconnect cable between the two

modules. The illustration below depicts the area

within a double-wide enclosure where the

corners of four modules meet.

NOTE: One wire on the module interconnect cable

may be a different color from the rest. The color has

no bearing on its orientation during installation.

Use Module Interconnect Cable to Wire Module to Module

MODULE

INTERCONNECT

CABLE ATTACHED

CONNECTION

NOT

MADE

4. Turn on the circuit breaker and verify that the

green PWR LED on the module lights, the

breaker does not trip, and power is delivered to

the loads.

5. Turn off the circuit breaker and remove the five-

position bypass jumper on the brown and red

section of the terminal block. The bypass jumper

on the blue section of the terminal block remains

installed. Refer to the figures in the next column

for a close-up of the jumpers.

NOTE: Before the five-position bypass jumper,

shown in the illustration, is removed, the Crestron

Professional Automation Computer (PAC2), which

provides control to the system, should be properly

connected and contain a valid program to provide

control of the module.

Wiring Diagram of the Terminal Block to the Module

(Single- -wide and Left Side Double wide Enclosures)

BYPASS JUMPER ON BROWN AND

RED SECTION OF TERMINAL

BLOCK HAS BEEN REMOVED

AFTER LOOSENING ALL SCREWS.

JUMPER ON BLUE SECTION

IS NOT REMOVED.

BLUE

BROWN

RED

ENLARGEMENT DETAIL:

JUMPER INSTALLED

BYPASS JUMPER

REMOVED

Wiring Diagram of the Terminal Block to the Module

(Right Side Double-wide Enclosures)

BLUE

BROWN

RED

BYPASS JUMPER ON BROWN AND

RED SECTION OF TERMINAL

BLOCK HAS BEEN REMOVED

AFTER LOOSENING ALL SCREWS.

JUMPER ON BLUE SECTION

IS NOT REMOVED.

ENLARGEMENT DETAIL:

BYPASS JUMPER

REMOVED

JUMPER INSTALLED

6. Turn on the circuit breaker.

NOTE: Power must be supplied to LINE for the

module to communicate with the control system or

for any of the circuits to operate.

Produktspecifikationer

Varumärke:	Crestron
Kategori:	Inte kategoriserad
Modell:	CLXI-1DIM4

Behöver du hjälp?

Om du behöver hjälp med Crestron CLXI-1DIM4 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Crestron Manualer

Crestron ZUMMESH-AVBRIDGE-I Bruksanvisning

25 September 2024

Crestron HD-TX-4KZ-421-CHGR Bruksanvisning

25 September 2024

Crestron HD-RX-4K-210-C-E Bruksanvisning

25 September 2024

Crestron DM-NAX-16AIN Bruksanvisning

25 September 2024

Crestron IV-CAMPTZ-12-N-SLVR-1B Bruksanvisning

25 September 2024

Crestron IV-CAMFR-12-N-SLVR-1B Bruksanvisning

25 September 2024

Crestron IVA-CPLT-1B Bruksanvisning

25 September 2024

Crestron IV-CAMA3-20-SLVR-1B Bruksanvisning

25 September 2024

Crestron IVA-CMT-BRKTJ-1B Bruksanvisning

25 September 2024

Crestron IVA-WMT-SHELF-1B Bruksanvisning

25 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024