Crestron SAROS ICE8LPT Bruksanvisning

Crestron högtalare SAROS ICE8LPT

Läs nedan 📖 manual på svenska för Crestron SAROS ICE8LPT (2 sidor) i kategorin högtalare. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Saros® Low Profile & Saros Express Low Profile 2-Way In-Ceiling Speakers

quickstart guide

SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT

www.crestron.com

Specifications subject to

change without notice.

SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT

Saros 2-way in-ceiling speakers are available in white or

black and may be painted to blend with the ceiling surface.

QUICKSTART DOC. 7493B (2037420) 06.21

1Installation

Saros® speakers by Crestron® deliver professional grade

performance and flexible installation in a range of popular

sizes for demanding commercial applications.

Ideal for use in music, paging, and sound reinforcement

systems, Saros speakers are engineered to achieve smooth,

even coverage, high output, and clear, natural sound quality

through the employment of horn loaded dome tweeters,

high-efficiency damped cone woofers, ported enclosures, and

precisely tuned crossovers.

Prepare the Mounting Hole

Front View - Grille Removed

Tighten Screws

Before finalizing the speaker location, check to make sure there are no fixtures, pipes, air ducts,

joists, or other possible obstructions. If applicable, use a good quality stud finder to locate joists.

If there are no obstructions, use the supplied template to trace an outline of the mounting hole.

For drop tile ceilings, remove the ceiling tile and place on a flat surface to trace the mounting

hole. For drywall or standard construction ceilings, use the template to trace the mounting hole

directly on the ceiling.

Install the Speaker Cable

Run the speaker cable (not included) from the audio source to the speaker location, observing

all appropriate local codes. Strip the ends of the speaker cables approximately 1/8 in. to 3/16 in.

(~3 mm to ~5 mm) and twist the strands .

Install the Tile Bridge

The included tile bridge components provide proper support when the speaker is installed in a

typical drop tile ceiling. Refer to the illustration below.

1. Based on the location of the mounting hole determined in the “Prepare the Mounting Hole”

section above, use the two supplied screws to attach the support ring to the rails so that

when installed, the ring is aligned with the mounting hole and the rails rest on the ceiling

grid frame.

2. The support ring position on the rails is adjustable to enable off-center speaker positioning.

The tile bridge assembly can be folded to fit through the speaker cutout in blind-mount

situations.

Speaker Cable Connections

Mount or Remove the Speaker

The in-ceiling speaker includes four toggle clamps that simplify the mounting process. If the grille is

mounted on the speaker, remove it before proceeding. (Refer to “Install or Remove the Grille” above.)

1. Referring to the illustrations to the right, remove the screw securing the rear cover panel, and lift

the cover panel off to expose the supplied terminal block.

2. Route the speaker cable through the cover cable clamp and connect the wires to the terminal

block, using the outer terminals: red to and black to . Use the inner and IN + – + – THRU

terminals to connect a pass-through (parallel) speaker.

3. Allow some slack in the speaker cable and position the cover panel on the back, making certain

it engages the mounting clips. Secure the cover panel using the screw removed in step 1, and

tighten the cable clamp to secure the cable. Do not overtighten. Use a safety tether

( (not included)) attached to the rear enclosure to prevent the speaker from SPKA-ST-15

accidentally falling.

4. The toggle clamps offer two positions to accommodate both standard and extra thick surfaces up

to 2.4 in. (61 mm). For extra thick tiles, reset the toggle clamps to the upper position.

a. With the toggle clamps turned inward, insert the speaker into the opening.

b. Hold the speaker against the ceiling and begin tightening the four screws on the front of the

speaker. The toggle clamps first rotate into clamping position (as indicated in the front view

illustration to the right) and then begin holding the speaker to the ceiling.

c. Tighten the screws until the speaker is secure. Do not overtighten.

Tile Bridge Assembly

Install or Remove the Grille

The zero-bezel frameless grille is held in place by powerful magnets. A safety tether is included to

prevent the grille falling from the ceiling. With the tether attached, place the grille in position on the

speaker. To remove the grille, grip the edges and pull away from the speaker.

Paint the Speaker Grille

Painting the Speaker grille should be done prior to mounting.

1. Carefully remove the mesh on the underside of the grille and set it aside for reinstallation. It may be

necessary to use a knife or other sharp instrument to free an edge of the mesh so it can be peeled

away. Use care to avoid cutting or tearing the mesh.

2. Dry brush or lightly spray paint grille. Use care to avoid clogging the holes in the grille.

3. Once the paint is dry, reinstall the mesh to the underside.

Set the Transformer Tap Selector Switch

The speakers are equipped with a 70V/100V matching transformer for distributed audio systems. The

transformer tap selector switch on the front panel is used to set the speaker power level. Use a flat blade

screwdriver to adjust the switch.

1. For SAROS_IC6LPT and SAROS_IC8LPT 70V systems, use the left side settings and select from

3.75 7.5 15 30 60, , , , or watts.

2. For SAROS_IC6LPT and SAROS_IC8LPT 100V systems, use the right side settings and select

from , , , or position should not be used.7.5 15 30 60 watts. The X

3. For SAROS_ICE6LPT 70V systems, use the left side settings and select from , , , or 3.75 7.5 15 30

watts.

4. For SAROS_ICE6LPT 100V systems, use the right side settings and select from , , or 7.5 15 30

watts. The X position should not be used.

5. For SAROS_ICE8LPT 70V systems, use the right side settings and select from or 7.5, 15, 30, 60

watts.

6. For SAROS_ICE8LPT 100V systems, use the right side settings and select from or 15, 30, 60

watts. The X position should not be used.

The switch may also be set to operation, bypassing the transformer completely. This setting should 8Ω

be used only for 8 Ω audio systems.

70V 100V

Safety Tether

Rigging Points

Terminal

Block

Screw

Speaker

Cable

THRU

Terminal Block

Not Shown

20.91 in.

(531 mm)

Support

Ring

Screws

(Supplied)

25.92 in.

659 mm

For SAROS_IC6LPT/IC8LPT

For SAROS_ICE6LPT

70V100V

For SAROS_ICE8LPT

70V100V

QUICKSTART DOC. 7493B (2037420) 06.21

Saros® Low Profile & Saros Express Low Profile 2-Way In-Ceiling Speakers

quickstart guide

SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT

www.crestron.com

Specifications subject to

change without notice.

SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT

The specific patents that cover crestron products are listed at .patents.crestron.com

Crestron, the Crestron logo, and Saros are either trademarks or registered trademarks of

Crestron Electronics, Inc., in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either

the entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible for

errors in typography or photography.

This document was writtren by the echnical Publications department at Crestron.T

3Specifications

SPECIFICATION

SAROS_IC6LPT/IC8LPT/ICE6LPT/ICE8LPT

SAROS IC6LPT SAROS_IC8LPT SAROS_ICE8LPT_The following table provides corrective action for possible trouble situations. If

further assistance is required, please contact a Crestron True Blue Support at

1-888-CRESTRON [1-888-273-7876].

Further Inquiries

To locate specific information or resolve questions after reviewing this guide,

contact Crestron True Blue Support at 1-888-CRESTRON [1-888-273-7876]

or, for assistance within a particular geographic region, refer to the listing of

Crestron worldwide offices at . www.crestron.com/offices

To post a question about Crestron products, log onto Crestron’s Online Help

at . First-time users must establish a user www.crestron.com/onlinehelp

account to fully benefit from all available features.

TROUBLE

POSSIBLE CAUSE(S)

CORRECTIVE ACTION

No sound or

intermittent

sound is

coming from

the speakers.

There is a cable

connection error.

Verify the cable connections

between the amplifier and

speakers.

The amplifier is not

receiving an input

signal or there is a

malfunction.

Verify that the amplifier is

functioning correctly, that it is

receiving an input signal, and

that the correct input source

is selected.

There is a faulty device

in the system.

Verify that all system devices

are functioning properly.

Constant noise

such as buzz,

hum, or hiss is

coming from

the speakers.

There is a system

grounding fault.

Verify that system grounding

is correct.

Low frequency

output is poor.

There is an incorrect

polarity connection at the

speaker or amplifier.

Verify the speaker

connection polarity ( on +

amplifier to on speaker).+

4Problem Solving

Troubleshooting

2Physical Views

Rear and Side View (Typical)

Construction

Enclosure Zinc-plated steel, plenum-rated, side-entry cable clamp

Baffle ABS UL94V-0 plastic

Grille Steel with textured finish, paintable, magnetically-held zero-bezel frameless, safety tether

Mounting Flush ceiling mount using 4 integral 2-step toggle clamps, 2.4 in. (61 mm) maximum surface thickness, tile

bridge included; (2) Rigging points for safety tether (SPKA-ST-15 sold separately).

Front View - Grille Removed (Typical)

10.64 in. (270 mm) not

including toggles

5.30 in. (135 mm)

9.70 in. (246 mm)

5.20 in. (132 mm)

9.2 lb (4.2 kg)

12.13 in. (308 mm) not

including toggles

5.30 in. (135 mm

11.20 in. (285 mm)

5.20 in. (132 mm)

10.8 lb (4.9 kg)

Dimensions

Diameter

Depth

Recommended

cutout diameter

Minimum mounting

depth

Weight

Connections

Input (1) 4-pin 5 mm detachable terminal block with screw-down flanges;

Speaker input with parallel pass-through;

Maximum Wire Size: 12 AWG

Controls

Transformer Tap (1) Recessed 5-position screwdriver adjustable rotary switch on baffle;

Used to select 70 /100 V tap settings or (bypass)V8Ω

Environmental

Temperature -2° to 120°F (-19° to 49°C)

Humidity 5% to 95% RH (non-condensing)

100V70V

8.0 in. (203 mm)

treated paper with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) treated

cloth dome, horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8Ω

7.5, 15, 30, 60 watts at

70V; 15, 30, 60 watts at

100V

80 Hz to 20 kHz (±3 dB)

65 Hz to 20 kHz (-10 dB)

60 watts program, (8 Ω)

89 dB @ (W/m)

95° conical (nominal)

8.0 in. (203 mm)

polypropylene with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) titanium

dome, horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8Ω

3.75, 7.5, 15, 30, 60 watts

at 70V; 7.5, 15, 30, 60

watts at 100V

65 Hz to 20 kHz (±3 dB)

55 Hz to 20 kHz (-10 dB)

50 watts program (8 Ω)

90 dB @ (W/m)

95° conical (nominal)

6.5 in. (165 mm)

polypropylene with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) titanium

dome, horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8Ω

3.75, 7.5, 15, 30, 60 watts

at 70V; 7.5, 15, 30, 60

watts at 100V

65 Hz to 20 kHz (±3 dB)

55 Hz to 20 kHz (-10 dB)

50 watts program, (8 Ω)

88 dB @ (W/m)

95° conical (nominal)

Woofer

Tweeter

Crossover Frequency

Impedance

Transformer Taps

Frequency Response

Frequency Range

Power Handling

Sensitivity

Coverage

6.5 in. (165 mm)

treated paper with ring

mode decoupled cloth

surround and steel basket

0.98 in. (25 mm) treated

cloth dome, horn-loaded

2.5 kHz

8 Ω nominal with

transformer set to 8Ω

3.75, 7.5, 15, 30 watts at

70V; 7.5, 15, 30 watts at

100V

85 Hz to 20 kHz (±3 dB)

70 Hz to 20 kHz (-10 dB)

60 watts program (8 Ω)

89 dB @ (W/m)

95° conical (nominal)

SAROS_ICE6LPT

12.13 in. (308 mm) not

including toggles

5.30 in. (135 mm)

11.20 in. (285 mm)

5.20 in. (132 mm)

11.1 lb (5.0 kg)

10.64 in. (270 mm) not

including toggles

5.30 in. (135 mm)

9.70 in. (246 mm)

5.20 in. (132 mm)

8.2 lb (3.7 kg)

Minimum

Mounting

Depth

Recommended

Cutout Diameter

Diameter

THRU

Produktspecifikationer

Varumärke:	Crestron
Kategori:	högtalare
Modell:	SAROS ICE8LPT
Färg på produkten:	Zwart
Vikt:	1138 g
Förpackningens vikt:	1820 g
Förpackningens bredd:	280 mm
Djuppackning:	327 mm
Förpackningshöjd:	141 mm
Snäll:	Alles-in-één vloeistofkoeler
Ursprungsland:	China
Maximalt luftflöde:	66.7 cfm
Antal fans:	2 ventilator(en)
Färg på belysningen:	Multi
Belysning LED:	Ja
Lämplig plats:	Processor
Harmoniserad systemkod (HS):	84733080
Ljudnivåventilation (min):	6 dB
Ljudnivåventilation (max):	30 dB
Fläktspänning:	12 V
Maximalt lufttryck:	2.34 mmH2O
Stöd för pulsbreddsmodulering:	Ja
Matventilator (bxdxh):	120 x 120 x 25 mm
Fläktkontakt:	4-pin
Fläkthastighet (max):	2000 RPM
Radiatormaterial:	Aluminium
Fläkthastighet (min):	650 RPM
Pumpljudnivå:	15 dB
Pompspänning:	12 V
Kylarens bredd:	119.6 mm
Kylarens djup:	277 mm
Kylarens höjd:	27 mm
Pompkontakt:	3-pin
Pump genomsnittliga felintervall (MTTF):	70000 uur
Fan Mean Failure Interval (MTTF):	160000 uur