Ctek Onyx Bruksanvisning

Ctek Batteriladdare Onyx

Läs nedan 📖 manual på svenska för Ctek Onyx (7 sidor) i kategorin Batteriladdare. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

ONYX

Battery Charger

For lead-acid batteries 14–225Ah

User’s manual and guide to

professional battery charging for

starter and deep cycle batteries.

INTRODUCTION

Congratulations on your purchase of your new professional ONYX Switch Mode Charger with

Pulse Maintenance, Float and Analysis. ONYX is a member of a family of professional chargers

from CTEK Sweden AB. It represents the state-of-the-art technology for battery charging. A

ONYX will prolong the lifetime of your battery. Read this user manual and follow the instructions

carefully before using the charger.

SAFETY

The charger is designed for lead-acid batteries 14–225Ah. Do not use the charger for any

other purpose.

Use safety glasses and turn your head away when connecting or disconnecting a battery.

Battery acid is corrosive. Rinse immediately with water if acid comes into contact with skin or

eyes. Seek medical advice.

Make sure that the cable is not being pinched or in contact with warm surfaces

or sharp edges.

While charging, a battery can emit explosive gases, so it is important to avoid sparks in the

immediate area.

Always provide for proper ventilation during charging.

Avoid covering the charger.

Make sure that the electrical cable does not come into contact with water.

Never charge a frozen battery.

Never charge a damaged battery.

Do not place the charger on the battery while charging.

The electrical connection must fulfil the national heavy current requirements.

Check the cabling in the charger before use. Make sure there are no cracks in the cabling or

in the protective covering. A charger with damaged cables may not be used.

Always check that the charger has gone over to maintenance charging mode before leaving

the charger unattended and connected for long periods. If the charger has not gone over

to maintenance charging within 3 days, this is an indication of a problem. In this case the

charger must be disconnected manually.

All batteries fail sooner or later. A battery that fails during charging is normally taken care of

by the chargers advanced control, but certain uncommon errors in the battery can still arise.

Don’t leave the battery charger unattended for a longer period of time.

Only mount the charger on a flat surface.

This equipment may not be used by children or by those who can not read and understand

the manual if they are not supervised by a responsible person who can guarantee that the

battery charger is being used in a safe manner. Store and use the battery charger out of the

reach of children. Make sure that children do not play with the battery charger.

BATTERY TYPES

The following recommendations should only be considered as guidelines. In the event of

uncertainty always refer to the battery manufacturer’s recommendations.

ONYX is suitable for charging all types of 12V lead-acid batteries: open batteries, MF, AGM and

most GEL-batteries. Battery sizes 14–225Ah.

•

CHARGING

Charging batteries mounted in a vehicle:

1. The power cord should be disconnected before connecting or disconnecting

the battery leads.

2. Identify the pole that is grounded (attached to the chassis). Ground is normally connected to

the negative terminal.

3. Charging a negatively grounded battery. Connect the red wire to the positive pole of the

battery and the black cable to the vehicle’s chassis. Be careful not to connect the black cable in

the vicinity of a fuel pipe or the battery.

4. Charging a positively grounded battery. Connect the black wire to the negative pole of the

battery and the red cable to the vehicle's chassis. Be careful not to connect the red cable in the

vicinity of a fuel pipe or the battery.

Charging of a battery not connected to a vehicle:

1. The power cord should be disconnected before connecting or disconnecting the

battery leads.

2. Connect the red wire to the positive pole of the battery and the black cable to the

negative pole.

Connecting the provided cables with eyelet terminals:

Make sure that the cable is not being pinched or in contact with warm surfaces or sharp edges.

When the cable is mounted on the battery, it should not be connected to the charger. Connect

the eyelet terminals to the battery's poles - the red cable to the positive pole and the black cable

to the negative pole. After this, the quick contact can be connected.

Reverse Polarity Protection

If the battery cables are connected incorrectly, the reverse polarity protection will make

sure that the charger and the battery are not damaged. In this case, the red warning

lamp (0) will be lit.

Start charging

1. Connect the power cord to the power outlet.

2. The lamp for Deep Discharged battery (1) will indicate if the battery voltage is low.

If lamp 1 blinks, this indicates that the battery is lightly sulfated. Read more under

”CHARGING PHASES”

3. Normal charging is indicated by the following lamps: Deep Discharged (1), Bulk Charge (2),

Absorption Charge (3) or Maintenance Charging (4). When the maintenance lamp is lit, the bat-

tery is fully charged. The charge will restart if the voltage drops. The charger can be connected

for months.

4. If the battery cables are connected incorrectly, the reverse polarity protection will make

sure that neither the charger nor the battery will be damaged. In this case, the red warning

lamp (0) will be lit.

5. If nothing happens. If none of the lamps come on this may be due to the connection to the

battery or chassis is poor or that the battery is faulty or has a too low terminal voltage. Another

cause may be a lack of voltage in the wall socket.

6. Charging can be interrupted at any time by disconnecting the power from the wall socket.

Always disconnect the power cable from the wall socket before removing the battery cables.

When you interrupt charging of a battery mounted in a vehicle, always disconnect the battery

cable from the chassis before removing the other battery cable.

Produktspecifikationer

Varumärke:	Ctek
Kategori:	Batteriladdare
Modell:	Onyx
Färg på produkten:	Black, Bordeaux
Värmekälla:	Kaphout
Vikt:	7000 g
Bredd:	535 mm
Djup:	665 mm
Höjd:	830 mm
Snäll:	Grill
Typ av material (överst):	Raster
Vormfaktor:	Ketel
Totala tillgångar:	- W
Lock:	Nee
Antal personer:	8 persoon/personen
Hjulhjul:	Ja
Kokytans diameter:	485 mm
Kokyta form:	Rond
Beläggning av hölje:	Emaille
Ben:	Ja
Antal ben/ben:	2 poot/poten