DataVideo RKM-150 Bruksanvisning

DataVideo Inte kategoriserad RKM-150

Läs nedan 📖 manual på svenska för DataVideo RKM-150 (1 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

HOLES FOR 1 AND 2

GANG E.O. BOXES

HOLES FOR

4" SQ. BOX

HOLES FOR

ATTACHMENT

TO SECURE

WALL

STRUCTURE

(SEE SAFETY

NOTE BELOW)

STEP 3

- SECURE CAMERA TO MOUNTING

BASE WITH (3) 3M SCREWS

PROVIDED WITH CAMERA

NOTE: SECURE RETAINING WIRE

(NOT SHOWN) UNDER ONE OF THE SCREWS

STEP 4

SLIDE CAMERA WITH MOUNTING BASE IN

POSITION OVER THE MOUNTING PLATE SLOTS.

SECURE (3) PLACES USING SCREWS

SHIPPED WITH CAMERA MARKED "A"

"A"

"A""A"

MODEL RMK-150 WALL MOUNT FOR DATAVIDEO HD/SD PTZ CAMERA PTC-150

P/N 21758

11-2-16

HARDWARE:

(4) 8-32 X 3/8" LONG PHILLIPS PAN HEAD SCREW

(4) # 8 LOCKWASHERS

(4) 1/4" X 2" LONG HEX HEAD LAG SCREWS

(4) 1/4" X 3" TOGGLE BOLT

ATTACH MOUNTING

PLATE TO EITHER SIDE OF

WALL MOUNT BRACKET

WITH (4) 8-32 SCREWS

AND LOCKWASHERS

STEP 1

- MOUNT BRACKET TO WALL USING APPROPRIATE

HARDWARE THROUGH THE .25" MOUNTING HOLES.

- ROUTE CABLES THROUGH WIRE MGMT PORTS.

- (MAKE CERTAIN MOUNTING METHOD IS SECURE AND

FOLLOWS ACCEPTED NORMS FOR THIS APPLICATION.

SEE NOTE BELOW).

- DO NOT USE EO BOX AS SOLE SUPPORT. WALL MOUNT

BRACKET MUST BE SECURED WITH SUFFICENT SIZE SCREWS

THROUGH .25" DIAMETER MOUNTING HOLES.

STEP 2

- ATTACH MOUNTING PLATE TO WALL BRACKET WITH

(4) 8-32 X 3/8" SCREWS AND LOCKWASHERS PROVIDED

THROUGH MOUNTING HOLES IN PLATE INTO TAPPED HOLES

IN WALL BRACKET.

NOTE: SECURE RETAINING WIRE ( NOT SHOWN) UNDER

ONE OF THE SCREWS & LOCKWASHER.

STEP 5

FINISH INSTALLATION BY ATTACHING ANY REQUIRED CABLES, LINES

OR ANY SECONDARY DEVICES AS REQUIRED PER MANUFACTURES

OR PROFESSIONAL INSTALLER'S INSTRUCTIONS.

SAFETY NOTE:

- Before beginning the installation, it is very important to examine the unit for damage, defects and correct hardware.

- The Installation instructions must be read and entirely understood prior to install.

- It must be determined that the mounting surface is capable of supporting the mount and equipment.

- The Professional Installer must determine the proper way to attach the WALL BRACKET MODEL XXXX

- The installation of the mount and equipment is dependent on proper/secure attachment and is the responsibility of the installer.

- Make sure wall will support 4 times the combined weight of Equipment aand Wall Mount.-

- This mount should be attached to woood studs only. Under no circumstances should this product be mounted to metal studs, unless an installation professional

deems they have been adquately reinforced and will support 4 times the combined weight of Equipment and the Wall Mount.

- Please use only the bolts supplied with the unit or bolts of the correct size, making sure the hardware used is tightened properly for a secure installation..

- The WALL BRACKET MODEL is only intended to be used with the equipment listed on the install sheet. It is not meant to be used with any other equipment.

- If at anytime, a question arises regarding this installation (or regarding the safety or integrity of the projected use) cease the installation

and either obtain the advice of another qualified installer or contact FEC.