Deaf Bonce Apocalypse AAK-4000.1D Bruksanvisning

Deaf Bonce mottagare Apocalypse AAK-4000.1D

Läs nedan 📖 manual på svenska för Deaf Bonce Apocalypse AAK-4000.1D (28 sidor) i kategorin mottagare. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/28

OWNER’S MANUAL РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ CAR AMPLIFIERS

MONOBLOCK CLASS D

http://deafbonce.com

AAK- 000.1D AAK-4000.1D AAK-5500.1D AAK-7500.1D AAK-12000.1D2

C O N T E N T S EN

1. Introduction

2. Safety instructions

3. Typical installation sequence

4. Connection methods

5. Wiring diagrams

6. Selection of the diameter of power cables and speaker cables

7. Speciﬁcations

8. Possible faults and their solutions

9. Box contents

10. Warranty and maintenance info

11. Information on disposal of the electrical and electronic equipment (for the European countries with

separate waste collection)

Thank you for purchasing this product!Deaf Bonce Deaf Bonce is committed to the creation of extremely high-proﬁle

systems with no loss of quality.

To ensure proper use, please read through this manual before using this product. It is especially important that you carefully

read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.

1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the ampliﬁer in cars,

trucks or buses, check the battery voltage.

2 . Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running,

depending on the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V.

Open circuit voltage (OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the

alternator and the battery capacity is enough to provide increased consumption.

For example, for the power of the ampliﬁer 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V

= 77 amperes. A more powerful ampliﬁer requires a more powerful alternator as well as an additional battery.

3 . Do not place the ampliﬁer in the engine compartment and also in the places exposed to water, moisture, dust or dirt.

4 . Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the

insulating layer, short circuit and ﬁre.

5. The ampliﬁer should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The

ampliﬁer should be in a place with a good air circulation. The horizontal position of the ampliﬁer is the best way to install.

6 . During the operation the ampliﬁer may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated

that may be dangerous.

7 . To improve the cooling of the ampliﬁer, it is recommended to clean periodically the heatsink from dust. When cleaning the

heatsink strong solvents should not be used as they may damage the ampliﬁer. Do not use compressed air, because solids can

penetrate inside the ampliﬁer. Cleanings best done with wet towels or cloth.

8 . Make sure that the location of the ampliﬁer does not violate the proper operation of mechanical and electrical devices of

the vehicle.

9. Make sure that during the installation and connection of the battery, the power cables are not shorted.

1 0. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe

or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.

11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies

close to the parts exposed to heat.

1 2. Make sure that all the cables are ﬁxed over the entire length. Also make sure that their outer protective shell is non-

combustible. Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the ampliﬁer.

1 3. Select a diameter of the power cable in accordance with the power of the ampliﬁer and the recommendations provided

here. Power cables are extremely important since they directly aﬀect the system damping factor and sound quality. The cables to

the battery must be in the copper crimp terminals pressed with the help of a hydraulic press, and well ﬁxed to the battery

terminals.

1 4. To avoid accidental damage, keep the ampliﬁer in its original packaging prior to installation.

15. Use high-quality copper speaker and power cables.

CAUTION!!! High sound pressure can damage your health!

Please use the common sense when controlling volume!

1 . I N T R O D U C T I O N

2 . S A F E T Y I N S T R U C T I O N S

1. Before installing the ampliﬁer disconnect the battery from the electrical system.

2 . To connect the ampliﬁer it is necessary to stretch the power cable from the location of the battery to the place of installation

of the ampliﬁer. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the

power cables)

3. Connect the power supply with the correct polarity. Connect all (+) terminals of the ampliﬁer to the cable from the positive

terminal of the battery and the (-) terminals of the ampliﬁer – to the cables running from the negative terminal of the battery.

4 . Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of

the power cable to the holder after connecting the other end to the ampliﬁer. Do not install the fuse.

5. Route all signal cables next to each other and separately from the power cables.

6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.

7 To connect the power wire supply is necessary to use special. power cables.

8. Fasten the ampliﬁer properly when installing it in the vehicle. If the component is disconnected during driving, it may cause

serious damage to the passengers of the car or another vehicle. It is not recommended to screw the ampliﬁer directly to the metal

it can lead to distorsions at the signal outputs.

9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.

Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the light

bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive terminal of

the battery.

When properly connected, the bulb must brieﬂy light up and go out. Now you may connect the positive lead to the (+)

battery. If the light does not go out, then something is wrong. This will prevent damage to the ampliﬁer in case of reverse polarity

and unwanted sparks when connecting. Install the rest of the fuses.

10 . To activate the ampliﬁer, it is necessary to apply the positive potential of 12 volts to the control input of the ampliﬁer (REM

IN) through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU).

11 . LED indicator on the front panel lights up in green, indicating that the device is turned on. LED indicator lights up in red

when the outputs are overloaded, if the temperature protection is activated, if there is a short circuit in the system cables to the

heatsink and if the ampliﬁer is faulty.

1 2. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the

sensitivity level of the ampliﬁer up until you hear distortions.

3 . T Y P I C A L I N S TA L L AT I O N S E Q U E N C E

Produktspecifikationer

Varumärke:	Deaf Bonce
Kategori:	mottagare
Modell:	Apocalypse AAK-4000.1D

Behöver du hjälp?

Om du behöver hjälp med Deaf Bonce Apocalypse AAK-4000.1D ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

mottagare Deaf Bonce Manualer

Deaf Bonce Avatar ABR-240.4 Bruksanvisning

22 September 2024

Deaf Bonce Apocalypse AAP-1600.1D Atom Plus Bruksanvisning

22 September 2024

Deaf Bonce Apocalypse AAB-3800.1D Bruksanvisning

22 September 2024

Deaf Bonce Machete MA-OGO1500.2D Sport Bruksanvisning

22 September 2024

Deaf Bonce Apocalypse AAB-7800.1D Bruksanvisning

22 September 2024

Deaf Bonce Apocalypse AAB-4900.1D Bruksanvisning

22 September 2024

Deaf Bonce Machete MA-130.4 Bruksanvisning

22 September 2024

Deaf Bonce Black Hydra HDA-4.90 Bruksanvisning

22 September 2024

Deaf Bonce Machete MA-50.4 Bruksanvisning

22 September 2024

Deaf Bonce Machete MLA-1000 Bruksanvisning

22 September 2024

mottagare Manualer

Nyaste mottagare Manualer

Speco Technologies PBM120AT Bruksanvisning

27 Oktober 2024

Fosi Audio V3 Bruksanvisning

26 Oktober 2024

Jensen CAR710-4BC Bruksanvisning

26 Oktober 2024

Onkyo TX-RZ830 Bruksanvisning

24 Oktober 2024

Pioneer VSX-1122K Bruksanvisning

22 Oktober 2024

NAD C 355BEE Bruksanvisning

21 Oktober 2024

Yamaha HTR-5072 Bruksanvisning

21 Oktober 2024

Yamaha RX-A810 Bruksanvisning

20 Oktober 2024

Sherwood R-607 Bruksanvisning

20 Oktober 2024

Denon AVC-S660H Bruksanvisning

19 Oktober 2024