Delta Dore Tyxia 5731 Bruksanvisning

Delta Dore mottagare Tyxia 5731

Läs nedan 📖 manual på svenska för Delta Dore Tyxia 5731 (1 sidor) i kategorin mottagare. Denna guide var användbar för 14 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/1
Recommendations
• IMPORTANT: the control wires are not
insulated from the mains power supply.
All connected equipment must be marked
CE and meet the requirements of the
low voltage devices as well as assembly
recommendations. Local control wires can
be extended up to 10 m
(separate from the
230 V).
• The roller shutter high and low stops must
be set before the receiver is installed.
• For the control of electric motors, please
contact us.
1 - Installation
1.1 Connection instructions for terminals 1 2 3 4.
- Strip the wires while respecting the strip length
specified on the product.
- Push the wire fully into the terminal.
1.1.1 Solid wires Stranded wires 1.1.2
1.2 Connection instructions for IN1 - COM - IN2 terminals
- Use the wires supplied.
- Push the wire fully into the terminal.
1.3 Connection
- Connect the motor control wires to terminals 3 and 4
(motor lowering control wire to terminal 3, raising control wire to terminal 4).
- Connect the switch to the IN1 - COM - IN2 terminals.
- Connect the 230 V power supply to terminals 1 and 2.
- Switch the installation power back on to continue with the association opera-
tion.
2 - Association
3 - Configuration
Configure the receiver according to
the type of switch connected.
Mode 1: Hold switch
Raise/Stop/Lower
Mode 2 (by default):
Raise/Lower double push-button
Raise + Lower: Stop
Mode 3: Raise/Stop/Lower/Stop
push-button
To modify the receiver configuration.
- Press the receiver's button for 6 seconds.
- The LED flashes, then becomes steady, release.
The number of flashes corresponds
to the current mode.
- Briefly press the receiver button to select the mode
.
- Confirm the selected mode by pressing the button for 3 seconds until the LED
switches off.
4 - Learning for the shutter travel time
Perform a complete cycle from stop to stop:
1- Lower or raise the roller shutter completely to the stop.
2- Do the reverse action until the opposite stop is reached.
Note: The learning for the shutter travel time adjusts itself automatically for
each complete cycle from stop to stop.
5 - Learning for the tilt time
Do not carry out this operation,
if the TYXIA 5731 controls an awning.
- Hold down the receiver button
for 9 seconds, the LED switches off,
then release. The shutter is positioned at the
midpoint of its height
- Press and hold the rotation button
(step by step mode) until the shutter
has rotated fully, then press stop.
- The tilt time is recorded.
6 - Help
Summary of functions:
0,75 - 1,5 mm
Ø
2
2
1
1234
> 6 s
TYXIA
1234
TYXIA
1234
TYXIA
1234
TYXIA
12
Use an electrically
isolated tool to
perform the actions
on the receiver confi-
guration button.
IPx4
230V~
OFF
Switch off the
installation
power supply
You can install the receiver for roller shutter
in a flush-mounted box behind a switch or
control push-button or in a sealed box inside
the roller shutter, a safe distance from metal
parts.
Removal recommendations
- Switch off the power supply.
- Use the tool supplied or a 2.5 mm screwdriver
to press the button of the front terminal before
removing the wire.
2
1
Removal recommendations
Turn the wire while pulling on it.
Do not strip the wires when they are
connected to the product as you
could damage the internal connector.
1
2
123 4
2
7mm 0,5 mm
KY31A02
123 4
230 V~
IN1
COM
IN2
1234
TYXIA
1 2 3 4
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
2
1
3
1
2
1
2
Hold switch
Double
push-button
Push
button
- Press and hold the receiver but-
ton for 3 seconds until the LED
flashes, release.
On the transmitter:
- Send the association command
(Refer to the user guide).
When the receiver LED has
stopped flashing.
The products are associated.
OK
OFF
1 2 3 4
TYXIA
1 2 3 4
... ... ...
> 3s
1 2 3 4
TYXIA TYXIA
TYXIA 2600
TYDOM
A
B
COM
IN1
IN2
CR 20 32
TYXIA
2600
> 3s
A B
> 3s
1 2
3
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
2
1
3
1
2
1
2
Do not interrupt
the roller shut-
ter travel.
Mode 1
Hold
switch
Mode 2
Double
push-button
Mode 3
Push button
• Quick press on the button.
A
Checking the receiver
operating mode.
Briefly press the button.
The LED flashes:
- 1 red flash: MODE 1
- 2 red flashes: MODE 2
- 3 red flashes: MODE 3
• Press and hold the button for
x seconds.
B
Association (refer to §2)
C
Configuration (refer to §3)
D
Learning for the tilt time
(refer to §5)
E
Removing an association
- Press the receiver's button for 12
seconds. (the removal method varies
according to the transmitter associated,
refer to the transmitter's user guide)
F
Removing all associations
- Press the receiver's button for 20
seconds.
- Press and hold until the LED switches off
after the rapid flashing phase.
- Release. The receiver has no wireless
connection.
G
Factory reset
- Press the receiver button for 30 seconds,
the LED flashes then switches off. The
receiver has no wireless connection and
the configuration is reset (mode 1 by
default).
The receiver locks in off mode.
When an overload is detected, the product
locks in off mode for 30 seconds before autho-
rising a new activation. The LED flashes rapidly
throughout this phase.
Contact our customer service.
20A circuit breaker
max. required.
3’’
BA
> > >6’’ 9’’ 20’’>12’’ 30’’>
C D F G
>
E
Association Removing an
association
Configuration
Factory
reset
Removing
all associations
Tilt
time
Using the tool supplied
or a 2.5 mm screwdriver,
press the terminal button
then insert the wire.
For the warranty and protection of your
shutters, we recommend the installation
of a wind sensor.
CV
P/N: 6351393
50%
TYXIA
>9s
Technical characteristics
- Power supply: 230 V~ 0.6 VA
• 2 Powered contact outputs: 2A
- Stand-by consumption: 0.06 W
- Number of associated transmitters:
16 maximum
- Storage temperature: -10°C/+70°C
- Operating temperature:
-10°C/+40°C
- IP 40 (flush mounting box)
- Dimensions: 41 x 36 x 14.5 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum radio power < 10 mW
- Receiver category: 2
EN - Receiver for Blackout Blinds
TYXIA 5731
EN
www.deltadore.com

Produktspecifikationer

Varumärke: Delta Dore
Kategori: mottagare
Modell: Tyxia 5731

Behöver du hjälp?

Om du behöver hjälp med Delta Dore Tyxia 5731 ställ en fråga nedan och andra användare kommer att svara dig


mottagare Delta Dore Manualer

Delta Dore

Delta Dore Delta 8000 BT Bruksanvisning

4 September 2024
Delta Dore

Delta Dore Tyxia 4600 Bruksanvisning

3 September 2024
Delta Dore

Delta Dore Tybox RF 6700 FP Bruksanvisning

3 September 2024
Delta Dore

Delta Dore Tyxia 5612 Bruksanvisning

2 September 2024
Delta Dore

Delta Dore Tyxia 4801 Bruksanvisning

2 September 2024
Delta Dore

Delta Dore Tyxia 5610 Bruksanvisning

1 September 2024
Delta Dore

Delta Dore Tyxia 4620 Bruksanvisning

1 September 2024
Delta Dore

Delta Dore Tyxia 4860 Bruksanvisning

1 September 2024
Delta Dore

Delta Dore RF 6420 Bruksanvisning

1 September 2024
Delta Dore

Delta Dore Tyxia 4840 Bruksanvisning

30 Augusti 2024

mottagare Manualer

Nyaste mottagare Manualer

Alto

Alto D1 Bruksanvisning

16 Januari 2025
Alto

Alto MC700.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.4 Bruksanvisning

16 Januari 2025
Alto

Alto MC250.8 Bruksanvisning

16 Januari 2025
Alto

Alto D4 Bruksanvisning

16 Januari 2025
Alto

Alto D3 Bruksanvisning

16 Januari 2025
Alto

Alto MC500.4 Bruksanvisning

16 Januari 2025
S.M.S.L

S.M.S.L PA200 Bruksanvisning

15 Januari 2025
Peavey

Peavey CKd 608 Bruksanvisning

15 Januari 2025
Wavtech

Wavtech link700.4plus Bruksanvisning

14 Januari 2025