DeWalt DS210 Bruksanvisning

DeWalt Inte kategoriserad DS210

Läs nedan 📖 manual på svenska för DeWalt DS210 (8 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

DS210 Indoor Motion Sensor – PIR

WARNING: Read and understand all instructions and

warnings for this product. In addition, read and follow all

instructions and warnings provided with the DS100 JobSite Security

Portable Alarm System.

CAUTION: DANGER OF EXPLOSION, INJURY, OR FIRE.

Carefully follow all instructions and warnings on the battery label and

package.

• Never use a damaged or worn out battery.

• Discharged batteries should be replaced only with type CR-123 3.0

Volt Lithium batteries.

• Do not use re-chargeable batteries or attempt to charge batteries.

• Carefully remove the old, discharged battery.

• Do not attempt to open.

• Do not peel the label from the battery.

• Never dispose of a battery in a fire.

• Dispose of used batteries in accordance with local regulations.

• Recycle batteries.

• Always insert batteries correctly with regard to polarity (+ and -)

marked on the battery and the equipment.

• When installing the battery, do not use excessive force. If the

battery does not fit, check to make sure that it matches the polarity

markings.

• Never expose the battery terminals to any other metal object. This

can short circuit the battery.

• Avoid exposure to temperature extremes.

• When not in use, store the battery in a cool, dark, dry place.

• Keep batteries out of reach of children.

CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR

FAILURE. Do not use near water. Damage to the equipment may

occur. Equipment shall not be exposed to liquids.

FCC REGULATORY STATEMENT (FCC: HCQ3B6ETICRM)

• This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) the device must accept any

interference received, including interference that may cause unde-

sired operation.

INDUSTRY CANADA (IC: 2309A-ETICRM)

•NOTICE: This equipment meets the applicable Industry Canada

Terminal Equipment Technical Specifications. This is confirmed

by the registration number. The abbreviation, IC, before the reg-

istration number signifies that registration was performed based

on a Declaration of Conformity indicating that Industry Canada

technical specifications were met. It does not imply that Industry

Canada approved the equipment.

Components (Fig. 1)

A. Antenna D. Tamper

B. Test Mode Reed Switch E. Battery

C. Reset Button

Product Function (Fig. 2)

The DS210 Indoor Motion Sensor – PIR (Passive Infrared) is a low-

current motion detector highly sensitive to moving heat sources. This

sensor provides a 50' (15.24m) range of protection with advanced

digital scanning to recognize human movements and size to help

prevent false alarms.

NOTE: The DS210 signals an unsecured condition when motion is

detected by the sensor. Once an unsecured condition is signaled,

further unsecured conditions are inhibited until no motion is sensed for

a period of more than 90 seconds. This feature is designed to conserve

battery life.

Once activated, this device will work exclusively with the assigned

DS100 JobSite Security Portable Alarm System.

• The DS210 features 900 MHz spread spectrum communication

with the Base Unit allowing for a range of up to 2000' (610m).

• The DS210 features a tamper (D) that notifies the system when

the sensor cover is removed.

• The DS220 device uses a CR-123 3.0V Lithium battery (E) for

long life.

• The reset button (C) allows the Indoor Motion Sensor – PIR to

be registered to any DEWALT JobSite Security System with

easy set up.

NOTE: Metal objects blocking radio frequency (RF) transmission can

affect the range of the sensor

Prevention of False Alarms

The majority of alarms that occur are false. These situations happen

every day due to user error, incorrect installation or improper mainte-

nance of the system. False alarms will limit the responsiveness to the

system, and become a general inconvenience. As the number of

false alarms increases, authorities have become less apt to respond

to alarm systems due to this problem. Many of these situations can be

avoided by following some very simple practices.

• Ensure all users are properly trained on the operation of the

system.

• Always turn off the system with the Key Chain Remote Control

before entering protected area.

• Lock all protected doors, windows or any other asset attached to

a sensor.

• Check that motion detectors are not obstructed. Do not allow

sources of heat or sound in range of the motion or vibration

sensors.

• Check that premises are cleared and assets secured before setting

the system.

FIG. 1

FIG. 3 FIG. 4

FIG. 2

CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR

FAILURE. Do not touch the electronic components inside

the device, except the reset button and battery.

MOUNTING

TAPE

HOOK &

LOOP

TOP VIEW

SIDE

VIEW

• Turn off all noise sources – radios, compressors, generators,

heavy equipment, etc.

• Know how to cancel an alarm or turn off the system before

activating.

• If a false alarm is tripped notify customer service immediately.

• Test the system on a monthly basis to ensure proper functioning

• Check cellular signal, power supply, and that sensors are secured

on a daily basis.

Recommended Locations

Recommended for use in enclosed areas, offices, climate controlled

storage, and monitoring interior spaces.

• The DS210 functions best when areas being protected are

bounded by solid barriers. Walls and floors provide good back-

drops for detecting moving heat (infrared) sources.

• For best detection, locate the motion sensor so that intruders

move across detection zone patterns, rather than toward or away

from the sensor (Fig. 2).

• Check areas for potential sources of false alarms. Remember

that the sensor responds to quick changes in heat patterns within

its coverage pattern. Avoid placing in direct or reflected sunlight,

or near objects that can be heated quickly by sunlight. Do not

place the DS210 looking at windows. Don’t place it near heating

or cooling sources, like heater ducts or air conditioners, which

might direct hot or cold air onto the sensor. Avoid appliances such

as space heaters which can rapidly heat up.

• Take into consideration the normal use of the area. Are there bats,

mice or other animals that could activate the sensor?

• Do not obstruct the coverage pattern with furniture or other

equipment.

Installing & Changing Battery

This wireless sensor requires a non-rechargeable CR-123 3.0 Volt

Lithium battery.

CAUTION: POTENTIAL EQUIPMENT MALFUNCTION OR

FAILURE. Do not touch the electronic components inside the device,

except the reset button and battery.

TO INSTALL BATTERY

1. Using a flat screwdriver, open the housing. Insert the screwdriver

about .25" (6mm) at the tab on the bottom of the unit (Fig. 3). The

screwdriver will enter the slot at about a 45˚ angle. Pry downward

on the handle of the screwdriver until the latch holding the cover

to the housing base releases.

2. Install the battery using the polarity (+ and -) markings on the

battery and equipment. Do not use excessive force. If the battery

does not fit, ensure that it matches the polarity markings (Fig. 1).

3. Press the Reset Button (C) on the device. After resetting the

sensor (see ), replace the cover. By open-Device Registration

ing the device, the Base Unit may display a tamper fault.

TO CLEAR A FAULT

a. Select Display.

b. Scroll list of fault(s).

c. Select Clear.

d. Enter master code.

e. Select OK.

TO CHANGE THE BATTERY

CAUTION: Never use a damaged or worn out battery.

1. Carefully remove the old, discharged battery. Dispose of the bat-

tery according to local regulations.

2. Install new battery using the polarity (+ and -) markings on the bat-

tery and equipment. Do not use excessive force. If the battery

does not fit, that it matches the polarity markings ensure (Fig. 1).

3. Press the Reset Button (C) on the device to re-register the sen-

sor and restore programming. After resetting the sensor, replace

the cover. By opening the device, the Base Unit may display a

tamper fault.

TO CLEAR A FAULT

a. Select Display.

b. Scroll list of fault(s).

c. Select Clear.

d. Enter master code.

e. Select OK.

Device Registration

To activate the device, it must first be assigned to your DS100 Base

Unit. Refer to the DS100 JobSite Security Portable Alarm System

Instruction Manual for more details on registering a device during the

initial setup.

NOTE: The system must be disarmed prior to any programming

changes.

1. Press the MAIN MENU button on the keypad of the DS100 Base

Unit.

2. Using the keypad, enter the master code.

3. Use the up and down arrows to scroll through the menu until the

System Settings menu is displayed. Select OK.

4. Use the up and down arrows to scroll through the menu until the

Wireless Device Maintenance menu is displayed. Select OK.

5. Use the up and down arrows to scroll through the menu until the

Add/Replace Device screen is displayed. Select OK.

6. The next available device number will be displayed. Up to 48 sen-

sors can be registered to the system. If there are no slots avail-

able, the screen will display ALL DEVICES IN USE. When the

device number is shown, select OK.

7. Using a flat screwdriver, open the housing. Insert the screwdriver

about .25" (6 mm) at the tab on the top of the unit. Pry downward

on the handle of the screwdriver until the latch holding the cover

to the housing base releases (Fig. 3).

8. When prompted by the LCD screen to RESET DEVICE, press and

release the reset button (C) located on the control board. The

screen will indicate that the device has been registered.

9. Snap the cover in place.

10. To edit the description of the device, select EDIT.

11. To edit the description, use the keypad to type a description of up

to 8 characters. The character that is being changed will be under-

lined. To move back a character, use the left/down arrow. To move

forward a character, use the right/up arrow. When complete, select

SAVE.

IMPORTANT: Write the device description and corresponding

device number on the included with theSensor Location List

DS100 JobSite Security Portable Alarm System. Keep this sheet

for reference. This information will be needed during the monitoring

service enrollment process. As device changes are made, be sure

to contact DEWALT customer service to make adjustments to the

monitoring service.

12. After registration, test the sensor. If programming through the initial

setup, the test function will be included in the setup sequence. If

adding the Indoor Motion Sensor after the alarm system has been

programmed, use the TEST button on the keypad.

Tests

WALK TEST

Wait 90 seconds since last motion was detected then walk through the

areas where protection is expected. When motion is detected, it will

unsecure and be removed from the test list on the Base Unit LCD

screen. Determine the limits of the coverage by repeating this test until

the motion is not detected.

COVERAGE TEST

While the system is unarmed, performing this test will indicate the

coverage area without sending an alarm. With the cover on the sensor,

hold a magnet on the bottom left side of the sensor until a red LED is

shown in the window. This activates the 1 minute test mode. Within

this period, a red LED will light every time the unit senses motion.

Mounting

• There are several options for mounting the DS210. The Indoor

Motion Sensor has two mounting holes on the back of the sensor

for easy installation using two #6 screws (provided) or two

#8 screws (not provided). Mounting tape and a hook and loop

fastener are also included. For mounting tape or hook and loop

fastener placement, see Figure 4.

• Mount the sensor 3–6' (.9–1.8m) from the floor. Any height outside

of this range will decrease the sensitivity of the motion detector.

• To eliminate false alarms, be sure that the sensor is secure so

it will not be bumped or otherwise moved.

Tamper – Faults

Faults indicate when there has been a serious issue that needs to be

addressed. This could be a number of things including an unsecured

device, low battery, tamper or weak signal.

If a fault is present, the system will chime and the Fault screen will be

displayed. To silence the chime, select SILENCE. To display the fault

and resolve immediately, select DISPLAY. Use the up and down

arrows to scroll through the faults. Resolve the issue with the action

listed in Description of Fault Codes chart.

TO REMOVE A TAMPER FAULT

1. Select CLEAR.

2. Use the keypad to enter the master code.

3. Select OK.

Full One Year Warranty

The DEWALT JobSite Security Portable Alarm System is warranted for

one year from date of purchase. We will repair, without charge, any

defects due to faulty materials or workmanship. For warranty repair

information, visit www.dewalt.com or call 1-800-4-DEWALT

(1-800-433-9258). This warranty does not apply to accessories or

damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

Fault Code Fault Display Description Action

DevPower Primary Power No battery power Change battery,

Lost Device # in device reset

DevLowBatt Low Battery Device battery Change battery,

Device # low reset

WeakSig Weak Signal Transmission signal Check for interference;

Device # from device is weak move device

Unsecured Unsecured Device has Check for intrusion;

Device # been tripped re-secure device

NoCheckIn No Check In Device check-in Check for interference;

Device # messages have move device

not been received

Tamper Tamper Device has been Close device or

opened or damaged replace if damaged

DESCRIPTION OF FAULT CODES

FIG. 1

FIG. 3 FIG. 4

FIG. 2

MISE EN GARDE : RISQUES DE MAUVAIS

FONCTIONNEMENT OU DE DÉFAILLANCE.

Ne pas toucher les composants électroniques à

l’intérieur du dispositif exceptés la pile et le

bouton de réinitialisation.

RUBANS

ADHÉSIF

CROCHETS

BOUCLES

Detecteur de mouvements iterieur

DS210 (PIR)

AVERTISSEMENT : Lire et comprendre tout avertissement

et toute instruction inclus dans ce manuel. De plus, lire tout

avertissement et toute instruction fournis avec le Système d’alarme

mobile de sécurité des chantiers DS100.

MISE EN GARDE : RISQUES D’EXPLOSION, DE BLESSURE

OU D’INCENDIE. Suivre attentivement toute instruction ou tout

avertissement inclus sur l’étiquette ou l’emballage des piles.

• Ne jamais utiliser une pile endommagée ou usée.

• Les piles déchargées doivent être remplacées par des piles au

lithium de type CR-123 de 3,0 volts.

• Ne pas utiliser de piles rechargeables ou tenter de recharger les

piles.

• Retirer soigneusement la vieille pile déchargée.

• Ne pas chercher à l’ouvrir.

• Ne pas retirer l’étiquette d’une pile.

• Ne jamais mettre une pile au feu.

• S’en défaire conformément aux régulations locales.

• Recycler les piles.

• Lors de l’installation des piles, toujours respecter la polarité (+ et -)

inscrite sur les piles et l’appareil.

• Pour installer une pile, ne pas forcer excessivement. Si la pile ne

rentre pas, vérifier que la polarité des bornes cadre avec les mar-

ques sur l’appareil.

• Ne jamais mettre les bornes des piles en contact avec tout autre

objet métallique. Cela pourrait provoquer un court circuit.

• Éviter de les exposer à des températures extrêmes.

• Après utilisation, entreposer les piles dans un lieu frais, sombre

et sec.

• Conserver les piles hors de la portée des enfants.

MISE EN GARDE : RISQUES DE MAUVAIS FONCTIONNEMENT

OU DE DÉFAILLANCE. Ne pas utiliser à proximité d’eau. L’appareil

risquerait d’être endommagé. Protéger l’appareil de tout liquide.

COMMUNIQUÉ DE LA FEDERAL COMMUNICATIONS

COMMISSION (FCC : HCQ3B6ETICRM)

• Ce dispositif est conforme aux dispositions du paragraphe 15 des

règlements de la FCC. Son utilisation est sujette aux deux condi-

tions suivantes : (1) Ce dispositif ne doit pas causer d’inter-

férences nuisibles, et (2) ce dispositif doit accepter toute inter-

férence reçue, y compris toute interférence pouvant causer un

fonctionnement indésirable.

INDUSTRIE CANADA (IC : 2309A-ETICRM)

•REMARQUE : Cet équipement se conforme aux Spécifications

Techniques pour Équipement Terminal d’Industrie Canada. Le

numéro d’enregistrement le confirme. L’abréviation « IC » devant

le numéro d’enregistrement signifie que l’enregistrement est basé

sur une Déclaration de Conformité indiquant que les spécifications

techniques d’Industrie Canada ont été respectées. Cela ne veut

pas dire que cet équipement a été approuvé par Industrie

Canada.

Description (fig. 1)

A. Antenne D. Altéré

B. Interrupteur Reed mode test E. Pile

C. Bouton de réinitialisation

VUE DE

DESSUS

VUE

LATÉRALE

Produktspecifikationer

Varumärke:	DeWalt
Kategori:	Inte kategoriserad
Modell:	DS210

Behöver du hjälp?

Om du behöver hjälp med DeWalt DS210 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad DeWalt Manualer

DeWalt DW790 Bruksanvisning

26 Oktober 2024

DeWalt DWH303DH Bruksanvisning

12 Oktober 2024

DeWalt DWH302DH Bruksanvisning

12 Oktober 2024

DeWalt DWV010 Bruksanvisning

12 Oktober 2024

DeWalt DWH304DH Bruksanvisning

12 Oktober 2024

DeWalt DWV015 Bruksanvisning

10 Oktober 2024

DeWalt DXV20S-QT Bruksanvisning

26 September 2024

DeWalt DXV23PPTA Bruksanvisning

26 September 2024

DeWalt DXV30SAPTA-QT Bruksanvisning

26 September 2024

DeWalt DXV38S-QT Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024