Dimplex 402TSFTi Bruksanvisning

Dimplex Spis 402TSFTi

Läs nedan 📖 manual på svenska för Dimplex 402TSFTi (4 sidor) i kategorin Spis. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

attention has to be given where children and

vulnerable people are present.

If the mains lead is damaged, it must be replaced

by the manufacturer or its service agent or a

similarly qualied person in order to avoid a

hazard.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is not advised when

connecting this product to the mains. Connection through these devices

could lead to a risk of overloading, overheating and even re at the extension

lead or adaptor due to inadequate connection quality.

This heater must be used on an ~ supply only and the voltage marked on

the heater must correspond to the supply voltage. This heater is tted with

a rewireable plug incorporating a 13 amp fuse. In the event of replacing

the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse must be

tted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code : GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the wire to the terminal marked ‘ ’ or GREEN AND YELLOW E

by the earth symbol , or coloured or .GREEN GREEN AND YELLOW

Connect the wire to the terminal marked ‘ ’ or coloured .BROWN L RED

Connect the wire to the terminal marked ‘ ’ or coloured BLUE N BLACK.

Using the heater

WARNING: DO NOT USE THE HEATER UNTIL THE FEET OR WALL

BRACKETS ARE FITTED CORRECTLY.

The product can be used as an installed or portable unit. Once the desired

application has been decided upon and the requirements below have been

met the product is ready to be used. Simply plug in and switch on at the

wall socket.

There are various control options available with various combinations

comprising of thermostat, switched, timer & indicating neons.

Please note – the element has been coated with a protective lm which

will burn off during the rst few minutes of use and may cause a small

amount of fuming. This is quite normal – the fumes are non-toxic and will

quickly disappear.

We recommend that you open a window to ventilate the room when using

the heater for the rst time.

Positioning the heater

Always ensure that the heater is stood on a rm, level base near to, but

not directly beneath, a suitable mains supply socket.

Ensure that curtains and furniture are not positioned close to the chosen

position, as this would create a potential re hazard.

We recommend that the heater should be wall-mounted in rooms where

children may be left unattended, see ‘Important Safety Advice’.

Important Safety Advice

WARNING: This appliance must not be used in

a bathroom.

WARNING: Do not use this heater in the

immediate surroundings of a bath, a shower or

a swimming pool.

WARNING: This heater must not be located

immediately below a xed socket outlet.

The heater carries a warning symbol to

alert the user to the risk of re that exists

if the heater is accidentally covered.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience or knowledge if they have

been given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided that

it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform

user maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

Dimensions

(Millimetres)

Installation and Operating Instructions

Dimplex Convector Heaters

Models : 402T, 402TS, 402TSTi, 402TSF & 402TSFTi

08/52558/2 Issue 2

Models Specication

402T 2.0kw Thermostat,

402TS 2.0kw Thermostat & 2 heat settings,

402TSTi 2.0kw Thermostat, Timer & Neon,

402TSF 2.0kw Thermostat & 2 heat settings, Turbo & Neon,

402TSFTi 2.0kw Thermostat, 2 heat settings, Timer, Turbo & Neon

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Fig. 1

Portable use

WARNING: THE HEATER SHOULD NEVER BE USED AS A PORTABLE

APPLIANCE WITHOUT THE FEET SECURELY FITTED.

Lay the heater on its back and remove the wall mounting brackets - see

Wall mounting Fig. 2(a). Locate and remove the foot xing screw - see .

Clip the foot in place and secure using the foot xing screw.

NOTE – The wall mounting brackets must be removed before the foot

can be tted.

Wall Mounting (Installed)

Three identical wall mounting brackets are secured to the base of the heater

with a xing screw. To wall mount appliance, rst remove the brackets as

follows, lay the heater on its back and follow the sequence shown - see

Fig. 3. Identify and remove the xing screw securing the brackets located

beside mains cable as shown in (a), pull out brackets and rotate them to

disengage them from the slot and withdraw the brackets from the slot (b).

Select a suitable position, near to a mains power socket whilst ensuring

the minimum mounting clearances are maintained - see . Fix the Fig. 1

two top retaining brackets to the wall, using suitable xings – see Fig. 4.

574

Locate the heater on the top brackets and allow it to hang in place.

Fit the bottom bracket into the slot in the heater and then x it to the wall.

Test that the heater is now securely xed to the wall.

Controls

Indicator Neon (selected models)

The indicator neon comes on when the appliance is connected to mains

supply.

Thermostat (all models)

The thermostat controls the heat output according to the room temperature.

This ensures that the heater will not produce heat unnecessarily when the

room is warm.

To set the temperature you require, Gradually turn the thermostat knob

clockwise until the desired temperature is reached. Allow some time between

increments for the room temperature to stabilise.

Alternatively to heat a cold room quickly, turn the thermostat knob to the

Max position. When the room has reached the desired temperature, turn

the thermostat knob anti-clockwise until the thermostat clicks off. The heater

will then automatically maintain this room temperature.

The thermostat also has a frost protection setting marked ‘ ’. This setting is

useful in areas such as garages to prevent frost damage. If the thermostat is

set to its minimum setting ‘ ’, the heater will cycle ON and OFF to maintain

a temperature of approximately 5°C to help protect against frosty conditions.

Switches (selected models)

Selected models are supplied with selector switches . There are two switch

types, one is an on/off switch and the other is a heat selection switch.

Depending on model either one or both switch may be included. The switch

operation is as follows.

On/Off: O - Off

I - On

Heat selection - Low heatI

II - High heat

Mechanical Timer (selected models)

Note: The timer clock will only operate when the product is connected to

the mains supply

Operation modes

There are two operating modes on the timer, Manual operation and Auto

operation. The operation mode is set using the slide switch on the timer

- see g6.

Manual operation (Position - I)

This setting allows power to the product uninterrupted by the timer,

however other product controls will continue to function as normal.

Auto operation (Position - )

This setting allows the heater to be controlled by the timer. The

product will be switched on and off depending on the pre-set timer

program.

Setting the time of day

To set the time of day, rotate the timer dial clockwise (indicated by the

arrow) until the correct time of day is opposite the reference mark -

see . The 24-hour clock is used ; e.g. 4 pm is ‘16’ (16:00hrs)Fig.6 .

Setting the ‘Auto’ ON and OFF times

To set the timer :

1. Using your nger tip or the tip of a pencil, push in as many

segments as necessary around the dial, according to the times you

don’t require heat – see . Each segment pushed in switches Fig. 7

the heater OFF for that part of the hour. All other segments will be

ON. For example, shows the timer set to switch the heater Fig. 7

OFF between 11pm and 1.45am.

2. You can select as many ON periods as you like, within the 24-hour

day. The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Fig.6

Fig. 4

Fig. 5

Fig. 3

Fig. 2

Fig. 7

Switching to auto

Ensure the thermostat and/or the heat selector are set for the desired

heat output.

Check that the clock shows the correct time of day. Set the mode slide

switch to , the heater will switch ON and OFF according to the timer

settings (see ).Fig. 9

Important notes

Remember to observe all safety warnings when operating the heater on

auto setting unattended or attended .

If the mains supply to the heater is interrupted, the timer clock will stop until

power is restored ; reset the time of day to ensure correct ON and OFF times.

Turbo fan(selected models)

The turbo fan is used to boost

the airow around the room. This

circulates the heat better and

results in a reduced heat up time

and a more even heat distribution.

The turbo fan is controlled by the

neon switch on the front of the

product.

The turbo can be turned on

ind epe nde ntly o f t he hea t,

however the fan will switch on

and off under the control of the

thermostat.

Note: on selected models in warm weather the fan can be used to circulate

cool air. Once the heat selection switches are in the off position and the

thermostat is set to ‘Max’ the fan will continue to function to circulate cool air.

Fig. 8

Safety – overheat protection

For your safety, this appliance is tted with a thermal cut-out. In the event

that the product overheats, the cut-out switches the heater off automatically.

To bring the heater back into operation, remove the cause of the overheating,

then unplug or turn off the electrical supply to the heater for a few minutes.

When the heater has cooled sufciently, re-connect and switch on the

heater.

Important Notes

Although this heater is manufactured to comply with the relevant safety

standards, certain types of carpets could become discoloured by the

temperatures under a portable heater. If you are concerned about this,

we recommend that you contact the carpet manufacturer for guidance.

Alternatively, either stand the heater on a suitable base to shield the carpet

or wall-mount it – call our Helpline for further advice.

You may notice some parts of the element appearing to be hotter from time

to time because of the variable airow through the heater. This does not

cause a safety hazard.

The heat outlet grille may become discoloured with use – this is caused by

airborne pollution and is not a fault.

Produktspecifikationer

Varumärke:	Dimplex
Kategori:	Spis
Modell:	402TSFTi
Färg på produkten:	Orange, Pink
Vikt:	310 g
Bredd:	217.2 mm
Djup:	11.3 mm
Höjd:	129 mm
Batterikapacitet:	2800 mAh
Blåtand:	Nee
Skärm diagonal:	7 "
Upplösning:	800 x 480 Pixels
Original bildförhållande:	16:9
Processorfrekvens:	1.2 GHz
Processorfamilj:	Rockchip
Antal processorkärnor:	2
Intern lagringskapacitet:	4 GB
Minneskortets maximala kapacitet:	- GB
Wi-Fi-standarder:	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Ljudformat som stöds:	AAC, APE, FLAC, MP3, OGG, WAV, WMA
Videoformat som stöds:	3GP, ASF, AVI, DAT, FLV, MOV, MP4, MPEG, MPG, RM, RMVB, TS, VOB, WMV
Plats position:	Nee
Bakre kameraupplösning (numerisk):	3 MP
Videoinspelning:	Ja
Inkluderar operativsystem:	Android
Plattform:	Android
Typ av anslutningskontakt:	3,5 mm
Medföljande kablar:	USB
Kompatibla minneskort:	MicroSD (TransFlash)
Touch-teknik:	Multi-touch
Pekskärmstyp:	Capacitief
Snabbstartsguide:	Ja
Inkluderar AC-adapter:	Ja
LED-bakgrundsbelysning:	Ja
Antal inbyggda högtalare:	1
USB-version:	2.0
Anslutning för nätadapter:	Ja
Inbyggd blixt:	Nee
Maximal videoupplösning:	- Pixels
Internminne:	0.5 GB
Bildformat som stöds:	BMP, GIF, JPG
Batteritid/batteritid:	3 uur
Internminnestyp:	DDR-SDRAM
Displayteknik:	TFT
WiFi-standard:	Wi-Fi 4 (802.11n)
Maximalt internminne:	0.5 GB
Fram kamera:	Nee
Backkamera:	Ja
Hörlurarna avstängda:	Ja
USB-kontakt:	Mini-USB B
Koptelefoon:	Ja
Surftid (Wi-Fi):	- uur
Batteriteknik:	Lithium-Ion (Li-Ion)
Minneskortplats:	Ja