Epson AN2WA87 Bruksanvisning

Epson Beamer AN2WA87

Läs nedan 📖 manual på svenska för Epson AN2WA87 (20 sidor) i kategorin Beamer. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/20
I N S T A L L A T I O N I N S T R U C T I O N S
Epson All-in-One Collaborative Whiteboard
AN2 87" and 100"
AN2 Series
AN2 Series Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installers responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a drywall thickness of 1/2" (12.7mm) forminimum
wood and steel stud walls, and NO drywall on concrete walls.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The AN2 Series includes the AN2 87" and
100" mounts. These mounts are designed to be used ONLY
with the following Epson projector models:
BrightLink Pro 1430Wi
BrightLink Pro 1420Wi
BrightLink 595Wi
BrightLink 585Wi
IMPORTANT ! :
The AN2 Series systems are designed to be
mounted to
:
a bare 8" concrete or 8"x8"x16" concrete block wall;
a 2" x 4" wood studs (16" on center minimum to 24" on
center maximum) wall with a minimum drywall
thickness of 1/2" (12.7mm);
a 2" x 4"-25ga minimum steel studs (16" on center
minimum to 24" on center maximum) wall with a
minimum drywall thickness of 1/2" (12.7mm).
--SAVE THESE INSTRUCTIONS--
Installation Instructions AN2 Series
3
DIMENSIONS
DIMENSIONS: INCHES
[MILLIMETERS]
AN2-87
DIMENSIONS: INCHES
[MILLIMETERS]
AN2-100

Produktspecifikationer

Varumärke: Epson
Kategori: Beamer
Modell: AN2WA87

Behöver du hjälp?

Om du behöver hjälp med Epson AN2WA87 ställ en fråga nedan och andra användare kommer att svara dig




Beamer Epson Manualer

Beamer Manualer

Nyaste Beamer Manualer