Eurolite LVH-2 Bruksanvisning

Eurolite Kontroller LVH-2

Läs nedan 📖 manual på svenska för Eurolite LVH-2 (4 sidor) i kategorin Kontroller. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
www.eurolite.de
USER MANUAL
BEDIENUNGSANLEITUNG
LVH-2
VIDEO DISTRIBUTOR
© Copyright
Nachdruck verboten!
Reproduction prohibited!
Acceptor
Endgerät
Feed-through signal or 75 terminator plugW
Durchschleifsignal oder 75 AbschlussW
additional LVH-2
weiterer LVH-2
Signal source
Signalquelle
12-24 V DC
A
B
LVH-2 VIDEO DISTRIBUTOR
LVH-2 VIDEO DISTRIBUTOR
VIDEO DISTRIBUTIONAMPLIFIER 1:4
The video distribution amplifier LVH-2 amplifies and distributes one video signal to four
outputs. Video inputs and outputs are made on the front panel via BNC jacks. Power
connections are made using block terminals on the rear panel. The input stage features a
parallel output for feed-through of the input signal. The gain potentiometer allows adjustment
from -1 dB to +7 dB.
SAFETY INSTRUCTIONS
• Before your initial start-up, please make sure that there are no transport damages. Should
there be any, do not take the device into operation and immediately consult your dealer.
• Operate the device only after having familiarized with its functions. Do not permit operation
by persons not qualified for operating the device.
• Protect the device against humidity and heat. Keep away from heaters and other
heating sources!
• We recommend a frequent cleaning of the device. Disconnect from mains first. Use
a soft lint-free and moistened cloth. Never use alcohol or solvents!
• There are no serviceable parts inside the device. Maintenance and service operations are
only to be carried out by authorized dealers.
• Damage, caused by manual modifications on the device are not subject to warranty. If the
device is used for other purposes than originally intended or if it is not correctly connected,
the product may suffer damages and the guarantee becomes void.
• This product is allowed to be operated with 12-24 V DC. This device falls under protection
class 3 and was designed for indoor use only.
OPERATION
Prior to connecting switch off all units and do not turn them on again until you have made all
necessary connections.
1 Connect the signal source (e.g. camera) via a 75 coaxial cable with BNC plugs to the
jack INPUT. The input signal fed through is available at the output LOOP OUT. This output
allows to connect the line input of another LVH-2 or a different unit (e.g. monitor). If the
output LOOP OUT is not used, the supplied 75 terminator plug must be connected (Fig.
A).
2 Connect each unit to which the video signal is to be distributed (e.g. monitor, recorder) via
a 75 coaxial cable with BNC plugs to the jacks AMPLIFIED OUTPUTS. Unused outputs
need not to be terminated (Fig.A).
3 To power the unit 12-24 V DC are required. For this purpose, connect a power source (e.g.
power supply unit, battery) to the terminals DC .Always observe the correct polarity.
Connect the marked core to the left contact (Fig. B).
4 The gain can be adjusted with the recessed potentiometer GAIN from -1 dB to +7 dB.
Adjust the potentiometer for 1 Vpp video level on your instrumentation. In the absence of
test equipment, adjust the value via the LED level indicator of the LVH-2. First turn the gain
counterclockwise. Then advance the gain clockwise unit the LED level indicator lights up.
TECHNICALSPECIFICATIONS
Power supply: .............12-24 V DC, 60 mA
1x video input:.............1 Vpp/ 1 k (bridged), 75 (terminated), BNC
5x video outputs:.........1 Vpp/ 75 , BNC (1 feed-through output, 4 amplified outputs)
Gain range:.................0 dB to +6 dB (0.9 to 2.25 Vpp)
Frequency response:..10 Hz to 10 MHz
S/N ratio:.....................>70 dB
Output isolation:..........>40 dB
Differential gain:..........0.1%
Differential phase:.......0.1 degree
Dimensions (LxWxH):.146 x 87 x 42 mm
Weight: .......................370 g
.
W
W
W
Ù Ù
Ù
12-24V
.
Please note: Every information is subject to change without prior notice. 20.12.2008 ©

Produktspecifikationer

Varumärke: Eurolite
Kategori: Kontroller
Modell: LVH-2

Behöver du hjälp?

Om du behöver hjälp med Eurolite LVH-2 ställ en fråga nedan och andra användare kommer att svara dig


Kontroller Eurolite Manualer

Eurolite

Eurolite LVH-1 Bruksanvisning

4 September 2024
Eurolite

Eurolite DMX Operator 192 Bruksanvisning

1 September 2024
Eurolite

Eurolite LVH-5 Bruksanvisning

31 Augusti 2024
Eurolite

Eurolite LVH-4 Bruksanvisning

31 Augusti 2024
Eurolite

Eurolite LVH-3 Bruksanvisning

30 Augusti 2024
Eurolite

Eurolite LVH-8 Bruksanvisning

29 Augusti 2024
Eurolite

Eurolite VSD-108 Bruksanvisning

29 Augusti 2024
Eurolite

Eurolite DMX Scene Setter 24/48 Bruksanvisning

29 Augusti 2024
Eurolite

Eurolite AVS-402 Bruksanvisning

27 Augusti 2024
Eurolite

Eurolite DPMX-1216 Bruksanvisning

26 Augusti 2024

Kontroller Manualer

Nyaste Kontroller Manualer

Nyko

Nyko Sound Pad Bruksanvisning

26 Februari 2025
Nyko

Nyko Air Glow 87303 Bruksanvisning

26 Februari 2025
Nyko

Nyko 87270 Bruksanvisning

26 Februari 2025
PowerA

PowerA Enhanced Wireless Controller Bruksanvisning

26 Februari 2025
Speed-Link

Speed-Link Black Bolt SL-650300-BK Bruksanvisning

21 Februari 2025
IPEGA

IPEGA PG-9078 Bruksanvisning

20 Februari 2025
Showtec

Showtec AirDrive 2.4 Pocket Bruksanvisning

20 Februari 2025
Axis

Axis TA4201 Bruksanvisning

20 Februari 2025
PowerA

PowerA Advantage Wired Controller Bruksanvisning

19 Februari 2025
PowerA

PowerA Enhanced Wired Controller Bruksanvisning

19 Februari 2025