Fantini Cosmi CH170D Bruksanvisning

Fantini Cosmi Termostat CH170D

Läs nedan 📖 manual på svenska för Fantini Cosmi CH170D (4 sidor) i kategorin Termostat. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

FANTINI COSMI S.P.A.

VIA DELL’OSIO 6

20090 CALEPPIO DI SETTALA (MI)

ITALIA

Phone no. +39 02 95682.222

Fax no. +39 02 95307006

E-mail: export@fantinicosmi.it

Web: www.fantinicosmi.it

APPLICATION AND USE

CH170D is a radio receiver (actuator) that coupled to a transmitter of the Fan-

tini Cosmi product line enables to remotely control a preset user (usually a

boiler).

Sent radio signal is free from interference with other device even if the same

frequency is used.

INSTALLATION AND CONNECTIONS

Installation shall be performed according to current CEI Standards.

The distance between actuator and transmitter must not exceed 30 m in closed

spaces and 70 m in open spaces (N.B. Range data could vary according to

environmental conditions). Do not shield the device with metallic parts.

Connect cables to the base terminal board according to the wiring diagrams

shown. Receiver power supply (230 V a.c.) shall be connected to terminals N

and L whereas the user (pump, burner, zone valve, humidistat, etc.) shall be

connected to terminals 1 and 2.

N.B. Several receivers can be connected to one transmitter.

OPERATION

The receiving device features three leds giving the following indications:

POWER ON: when this led is on it indicates that the receiver is properly

powered. The meaning of the different colours of this led is specied below.

AUTO: when this led is on it indicates that the receiver is congured in AUTO-

MATIC MODE. When the led is off the MANUAL MODE is active.

CONTACT STATUS: when this led is on it indicates that the relay contact

is closed, otherwise (led off) it will be open.

CH170D RADIO ACTUATOR FOR DIN RAIL MOUNTING

CONTACT STATUS

AUTO

POWER ON

Boiler

30 metres max.

Receiver

Transmitter

Chronothermostat/

thermostat

N L 4 1 2

Each time the button is pressed the three operating modes are started in

turns:

AUTOMATIC

(“AUTO” led: ON)

In this operating mode, the receiver receives a radio signal coded by the chron-

othermostat via the transmitter interface and triggers the integral relay. The

“POWER ON” led takes on a different colour according to the quality of the

signal received:

• RED: signal absent or very disturbed

• ORANGE: satisfactory reception

• GREEN: good reception

Fast and brief led ashing indicates the reception of radio data sent by the

transmitter.

230V50Hz

MANUAL ON

(“AUTO” led OFF and “CONTACT STATUS” led ON)

In this operating mode, the receiver relay contact is always closed and the

radio transmission implemented by the transmitter module is ignored (conse-

quently chronothermostat / thermostat commands are not accepted).

MANUALE OFF

(“AUTO” led OFF and “CONTACT STATUS” led OFF)

In this operating mode, the receiver relay contact is always open and the radio

transmission implemented by the transmitter module is ignored (consequently

chronothermostat / thermostat commands are not accepted).

SYSTEM CODE SELF-LEARNING PROCEDURE

Before using the CH170D actuator in AUTOMATIC mode its code shall be

memorised into the Fantini Cosmi transmitter you purchased. To prevent stor-

ing of a different code, during the conguration procedure the reception sen-

sitivity is reduced and therefore the distance between transmitter and receiver

shall be 2 m max. Proceed as follows:

1. Turn the receiver on and then keep the button pressed until selecting the

AUTOMATIC MODE (see paragraph “OPERATION”).

2. Keep the button pressed for over 10 seconds to start the “SELF-LEARNING”

procedure, the “AUTO” led will start ashing.

3. Force radio thermostat / chronothermostat transmission (refer to the relevant

user’s guide).

4. Carry out the OPERATION CHECK procedure to check for correct congu-

ration of the programmed receiver.

N.B.: Max. 45 seconds shall pass between step 2 and step 3 of the above

procedure.

Receiver “POWER ON” led will turn red if over two minutes pass without re-

ceiving data.

OPERATION CHECK

To use the chronothermostat/ thermostat refer to the relevant instruction

manuals.

-Make sure the receiver is in AUTOMATIC mode (see paragraph OPERA-

TION).

-Wait for chronothermostat/ thermostat data transmission and then check

whether CH170D relay status matches with chronothermostat/ thermostat.

- Switch over chronothermostat/ thermostat and check whether the CH170D

relay status changes.

Should the “POWER ON” led be red then transmitter and receiver are too dis-

tant: communication between the two devices is null or unreliable.

Produktspecifikationer

Varumärke:	Fantini Cosmi
Kategori:	Termostat
Modell:	CH170D
Färg på produkten:	Zwart
Vikt:	3250 g
Bredd:	280 mm
Djup:	200 mm
Höjd:	210 mm
Snäll:	Home audio-microsysteem
På / Av knapp:	Ja
USB uttag:	Ja
Hörlurarna avstängda:	Ja
Frekvensomfång:	40 - 18000 Hz
Antal kanaler:	- kanalen
XLR in:	Ja
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 Hz
Strömförbrukning (typiskt):	80 W
Synkronisering av ingångsimpedans:	4 Ohm
Linjeingångar (RCA):	1
Bearbetar digitalt ljud:	- Bit