Fantini Cosmi K20A Bruksanvisning

Läs nedan 📖 manual på svenska för Fantini Cosmi K20A (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
K20A-K30A-K40A
SELF-ADJUSTING HEATING CABLES
TO MAINTAIN THE TEMPERATURE OF FLUIDS
Suitable for maintaining the
temperature of liquids inside pipes
Power delivered
~20, ~30, ~40 W/m at 10°C
Optimisation of energy
consumption thanks to the self-
adjusting feature of the cable
CODE Cable
length
Power
at 10°C
Minimum
installation
room
temperature
Maximum
room
temperature
powered
Maximum
room
temperature
not powered
Maximum length
of the heating circuit
from the supply point
K20A25 25 m 20 W/m -35 °C 65 °C 80 °C 170 m
K20A50 50 m 20 W/m -35 °C 65 °C 80 °C 170 m
K20A100 100 m 20 W/m -35 °C 65 °C 80 °C 170 m
K20A500 500 m 20 W/m -35 °C 65 °C 80 °C 170 m
K30A25 25 m 30 W/m -35 °C 65 °C 80 °C 140 m
K30A50 50 m 30 W/m -35 °C 65 °C 80 °C 140 m
K30A100 100 m 30 W/m -35 °C 65 °C 80 °C 140 m
K40A25 25 m 40 W/m -35 °C 65 °C 80 °C 120 m
K40A50 50 m 40 W/m -35 °C 65 °C 80 °C 120 m
K40A100 100 m 40 W/m -35 °C 65 °C 80 °C 120 m
OPERATION
The heating cables automatically vary the heat
emission without control thermostats
being used;
They consist of conductors insulated by polymers,
which vary their resistance according to the
temperature which they are subjected to.
HOMOLOGATION AND STANDARDS
CSTB
K20A-K30A-K40A - SELF-ADJUSTING HEATING CABLES TO MAINTAIN THE TEMPERATURE OF FLUIDS
INSTALLATION
The cable can be cut to the desired length;
The total power depends on the length of the
heating cable and the perceived temperature;
The cable is secured along the pipe with the
relevant fixing tape K50 for steel pipes or K50AL
for plastic pipes;
Minimum bending radius: 25 mm;
Use a C01A, C03A or L03BM1A type thermostat to
disconnect the heating cable when the temperature
of the fluid is at the desired temperature, thereby
minimising energy consumption;
The cable heats up along its entire length and can
be wound in overlapping spirals as it will limit its
power at the overlapping points;
The two conductors must be kept insulated at
the end of the cable using the kit to seal the ends
code KIT2A and must never be in contact with each
other;
It is advisable to apply an insulating coating over
the heating cable.
Power supply 230V-50Hz
Tolerance -0/+5 W
Power delivered K20A
20 W/m at 10°C
K30A
30 W/m at 10°C
K40A
40 W/m at 10°C
ELECTRICAL FEATURES
Pipe temperature °C
Power W/m
50
50
50
5050
45
45
45
4545
40
40
40
4040
35
35
35
3535
30
30
30
3030
25
25
25
2525
20
20
20
2020
15
15
15
1515
10
10
10
1010
5
5
5
55
0
0
0
00
0 10 20 30 40 50 60
0 10 20 30 40 50 60
0 10 20 30 40 50 60
0 10 20 30 40 50 600 10 20 30 40 50 60
K40A
K30A
K20A
K20A-K30A-K40A - SELF-ADJUSTING HEATING CABLES TO MAINTAIN THE TEMPERATURE OF FLUIDS
GENERAL FEATURES
Cable composition 1.25 mm² conductors
Self-adjusting conductive core
Polyolefin insulating sheath
Braided copper sheath
Outer sheath in modified polyolefin
Cable length K20A25
K20A50
K20A100
K20A500
K30A25
K30A50
K30A100
K40A25
K40A50
K40A100
25 m
50 m
100 m
500 m
25 m
50 m
100 m
25 m
50 m
100 m
Minimum installation room temperature -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Cable dimensions 12.6 x 4.8 mm series K20A
14.6 x 4.8 mm series K30A-K40A
CALIBRATION OF THE PROTECTION CIRCUIT
CODE ROOM
TEMPERATURE
CALIBRATION BASED ON MAXIMUM CABLE LENGTH
16A 20A 32A
Series K20A
-20 °C 105 130 170
0 °C 150 170 -
10 °C 170 - -
Series K30A
-20 °C 75 90 140
0 °C 97 120 -
10 °C 115 140 -
Serie K40A
-20 °C 55 70 110
0 °C 70 90 120
10 °C 80 100 -

Produktspecifikationer

Varumärke: Fantini Cosmi
Kategori: Inte kategoriserad
Modell: K20A

Behöver du hjälp?

Om du behöver hjälp med Fantini Cosmi K20A ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Fantini Cosmi Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer