Fellowes Powershred LX20M Bruksanvisning

Fellowes Dokumentförstörare Powershred LX20M

Läs nedan 📖 manual på svenska för Fellowes Powershred LX20M (8 sidor) i kategorin Dokumentförstörare. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
Please Read These Instructions Before Use.
Veuillez Lire Ces Instructions Avant D’utiliser L’appareil.
Lea Estas Instrucciones Antes Del Uso.
Will shred: Paper, credit cards, staples and paper clips
Will not shred: Adhesive labels, continuous form paper,
transparencies, newspaper, cardboard, CD/DVDs, laminates,
file folders, X-rays or plastic other than noted above
Paper shred size: Micro-Cut, 5/32 in x 1/2 in (4mm x 12mm)
Maximum Sheets per pass:
LX20M - 12*, LX21M - 16*, LX22M - 20*
Maximum Paper entry width: 9 in. (230mm)
Plug in and put disconnect power
switch in ON (I) position
* 8.5 in. p2-x11 in., 20lb., (75g) paper at 120V/60 Hz, 4.0Amps (LX20M), 4.8Amps (LX21M), 5.8Amps (LX22M); heavier paper, humidity or other than
rated voltage may reduce capacity. Maximum recommended daily usage rates: *1000 sheets per day, 25 credit cards. Fellowes SafeSense ®
shredders are designed to be operated in home and office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees
Celsius) and 40 – 80% relative humidity.
CAPABILITIES
BASIC SHREDDING OPERATION
Align paper/card to center of paper
entry. Feed straight into paper entry
and release.
2
16
PAPER OR CARD
A. SafeSense® Technology
B. Paper entry
C. See safety instructions
D. Pullout bin
E. Casters
F. Disconnect power switch
1. OFF
2. ON
G. Control Panel and LEDs
LX20M
Continuous operation. Up to 10-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 10-minutes will trigger
15-minute cool down period.
LX21M
Continuous operation. Up to 20-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 20-minutes will trigger
15-minute cool down period.
LX22M
Continuous operation. Up to 30-minutes maximum.
NOTE: Shredder runs briefly after each pass to clear entry.
Continuous operation beyond 30-minutes will trigger
15-minute cool down period.
1
ENGLISH
2
LX /LX20M 21M LX22M
F.
G.
A.
B.
D.
E.
C.
F.
A.
B.
D.
E.
C.
G.
WARNING IMPORTANT SAFETY INSTRUCTIONS Read before using!
• Operation,maintenance,andservicerequirements
are covered in the instruction manual. Read
the entire instruction manual before operating
shredders.
• Keepawayfromchildrenandpets.Keephands
away from paper entry.
• Keepforeignobjects–gloves,jewelry,clothing,hair,
etc.–awayfromshredderopenings.Ifobjectenters
top opening, switch to Reverse ( ) to back out
object.
• DONOTuseaerosolproducts,petroleumbasedor
aerosol lubricants on or near shredder. DO NOT USE
“CANNED AIR” OR “AIR DUSTERS” ON SHREDDER.
Vapors from propellants and petroleum based
lubricantsmaycombustcausingseriousinjury.
• Sharpedges,DONOTtouchexposedcuttingblades
under shredder head.
• Donotuseifdamagedordefective.Donot
disassemble shredder. Do not place near or over
heat source or water.
• ThisshredderhasaDisconnectPowerSwitch
(F) that must be in the ON ( ) position to
operate shredder. In case of emergency, move
switch to OFF (O) position. This action will
stop shredder immediately. Always turn off or
unplug when not in use for an extended period
of time.
• Shreddermustbepluggedintoaproperly
grounded wall outlet or socket of the voltage
and amperage designated on the label. The
grounded outlet or socket must be installed
neartheequipmentandeasilyaccessible.
Energy converters, transformers, or extension
cords should not be used with this product.
• FIREHAZARD–DoNOTshredgreetingcards
with sound chips or batteries.
• Forindooruseonly.
• Unplugshredderbeforecleaningorservicing.
ADVANCED PRODUCT FEATURES
OILING SHREDDER
Allmicro-cutshreddersrequireoilforpeakperformance.Ifnot
oiled, a machine may experience diminished sheet capacity,
intrusive noise when shredding and could ultimately stop
running. To avoid these problems, we recommend you oil your
shredder each time you empty your waste bin.
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free
operation. However, on rare occasions the sensors may
become blocked by paper dust causing the motor to run
even if there is no paper present. (Note: two paper detection
sensors are located in the center of the paper entry).
PRODUCT MAINTENANCE
1
16
23
14
16
*Apply oil across entry
Locate Auto-
start infrared
sensor
Dip cotton
swab in
rubbing
alcohol
Using cotton
swab, wipe
away any
contamination
from the paper
sensors
2Press and hold forward ( >)
2-3 seconds
*Only use a non-aerosol
vegetable oil in long
nozzle container such as
Fellowes 35250
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is
illuminated, the shredder has exceeded its maximum
operating temperature and needs to cool down. This indicator
will remain illuminated and the shredder will not operate for
the duration of the recovery time.
Bin Open: The shredder will not run if the bin is open. When
illuminated, close the bin to resume shredding.
Bin Full: When illuminated, the shredder waste bin is full and
needs to be emptied. Use Fellowes waste bag 36052 (LX20M/
LX21M), 36053 (LX22M).
SafeSense® Indicator: If hands are too close to the paper
entry, the SafeSense® indicator will illuminate and the shredder
will stop shredding. If SafeSense
® is active for 5 seconds, the
shredder will automatically turn off and the user must open and
close the bin or toggle on/off the power switch on the rear.
Power: If the machine is not powered, ensure the power
switch is in the ON (I) position and the power cord is plugged
into both the machine and power outlet.
OVERHEAT
INDICATOR
BIN
OPEN
BIN
FULL
SAFESENSE®
INDICATOR
POWER
SWITCH
1. Run Time Indicator:
Light will turn yellow when machine is
close to the maximum runtime and switch
to red when cool down is needed
2. SafeSense® Technology:
Light will turn yellow to alert when system is
activated. Machine will turn off after 5 seconds
of hands touching the paper entry (open bin or
switch power on/off to resume shredding)
3. Reverse:
Light will turn green
4. Forward:
Light will turn green
5. Bin Open:
Light will turn red when bin is pulled out
6. Bin Full Indicator:
Light will turn yellow when nearly full and
turn red when it needs to be emptied
7. Efficiency Meter:
Light will turn blue when powered on and ready.
Light will expand green and when optimal shredding
zone is reached it will pulse. Once the optimal level
is surpassed, the light will turn yellow, then red to
preventfeedingtoomanysheets.Ifmachinejams,
the light will turn red and paper will auto reverse.
1 2 3 4 5 6. . . . . .
7.
Energy saving feature shuts down automatically after 2 minutes
of no shredding activity. Insert paper, press forward/ reverse or
open and close the bin to resume shredding.
With 5 Responsive Features. The revolutionary fearless
shredder lineup that maximizes workplace efficiency and
keeps your day in flow.
IntelliBAR
3
Turn off
disconnect
power switch
(O) and unplug
the shredder
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE TO CLEAN THE SENSORS

Produktspecifikationer

Varumärke: Fellowes
Kategori: Dokumentförstörare
Modell: Powershred LX20M

Behöver du hjälp?

Om du behöver hjälp med Fellowes Powershred LX20M ställ en fråga nedan och andra användare kommer att svara dig




Dokumentförstörare Fellowes Manualer

Dokumentförstörare Manualer

Nyaste Dokumentförstörare Manualer