Festo DADP-DGC-18-KF Bruksanvisning

Festo Inte kategoriserad DADP-DGC-18-KF

Läs nedan 📖 manual på svenska för Festo DADP-DGC-18-KF (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
3.
DADP-DGC
Shock absorber retainer
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Assembly instructions
8174040
2022-11c
[8174042]
8174040
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
èwww.festo.com/sp.
Document Product Table of contents
Operating instruction Linear drive DGC(I)
Assembly instructions Stop KYC
Operating instruction Intermediate-position module
DADM-DGC-25...40
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Only use the product in its original condition without unauthorised modifica-
tions.
Observe the tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2 Intended use
The shock absorber retainer fastens shock absorbersYSR(W)-DGC to the slide of
linear drivesDGC-...-GF/-KF/-FA or DGCI. Use the shock absorber retainer only in
combination with a counter part for the cushioning:
Stop KYC
Intermediate-position module DADM-DGC
3 Additional information
Contact the regional Festo contact if you have technical problems
èwww.festo.com.
Accessories èwww.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
2
3
4
Fig.1
1
Shock absorber retainer (1x)
2
Centring sleeve (2x)
3
Screw (2x),
only with DADP-DGC-…-KF
4
Screw (2x)
4.2 Not in scope of delivery
5
Fig.2
5
Linear drive (1x)
DGC-...-GF
DGC-...-KF,
DGC-...-FA,
DGCI
6
Fig.3
6
Stop (1x/2x)
KYC
7
Fig.4
7
Shock absorber (1x/2x)
YSR(W)-DGC
8
Fig.5
8
Intermediate-position module
DADM-DGC
5 Assembly
5.1 Preparation for DADP-DGC-18…-40
ZW X YV
Fig.6
Check the slide of the linear drive .5
Steel slide:
Multi-piece slide[V]
Screws[W], spring pins[X] and plastic cover[Y]
Aluminium slide:
One-piece slide[Z]
5.2 Mounting shock absorber retainer
2
A
1
3
V
Fig. 7: Mounting on steel slide
2
A
1
4
Z
Fig. 8: Mounting on aluminium slide
1. Place the centring sleeves in the seats[A].2
2. Place the shock absorber holder on the centring sleeves .1 2
Select the appropriate screws / :3 4
shorter screws for multi-piece steel slide[V].3
longer screws for one-piece aluminium slide[Z].4
Two screws are left over with DADP-DGC-…-KF.
4. Tighten the screws / . Observe the tightening torque.3 4
DADP-DGC -18-GF -25-GF -32-GF -18-KF -25-KF -32-KF
Screw M5 x 303
Screw M5 x 30 M5 x 354
[Nm] 4 6
DADP-DGC -40-GF -40-KF -50 -63
Screw M6 x 35 3
Screw M6 x 35 M6 x 45 M8 x 454
[Nm] 8 10 25
5.3 Mounting shock absorber
If available, shock absorbers from the end cap of the linear drive can be used.5
7
B
Fig.9
Depending on requirements screw one or two shock absorbers with stop7
sleeve and lock nut completely into the shock absorber retainer . Observe1
the tightening torque of the lock nut.
YSR(W)-DGC -18-GF -25-GF -32-GF -18-KF -25-KF -32-KF
[Nm] 3 5 8 5 20 20
YSR(W)-DGC -40-GF -40/50-B -63
[Nm] 20 35 30
5.4 Mounting stop elements
1. Mount one or two stops depending on requirements 6è1 Applicable
documents.
2. Mount intermediate-position modules depending on requirements 8è1
Applicable documents.

Produktspecifikationer

Varumärke: Festo
Kategori: Inte kategoriserad
Modell: DADP-DGC-18-KF

Behöver du hjälp?

Om du behöver hjälp med Festo DADP-DGC-18-KF ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Festo Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer