Festo DADP-SP-G9-20-R Bruksanvisning

Festo Inte kategoriserad DADP-SP-G9-20-R

Läs nedan 📖 manual på svenska för Festo DADP-SP-G9-20-R (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
DADP-SP-G9-...-R
Sub-base kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Assembly instructions
8195137
2023-07a
[8195139]
8195137
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
èwww.festo.com/sp.
Document Product Contents
Operating instruction Mini slide DGSS
Operating instruction Shock absorber DYEF, DYSS
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Only mount the product on components that are in a condition to be safely
operated.
2.2 Intended use
The sub-base kit in combination with two shock absorbers on the mini slide DGSS
cushions its extended and retracted end position. The sub-base contains the axial
air connections for the mini slide.
3 Additional information
Contact the regional Festo contact if you have technical problems
èwww.festo.com.
Accessories èwww.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
2
3567 4
Fig.1
1
Screw (2x)
2
Stop (1x)
3
Stop element (1x)
4
Screw (2x)
5
O-ring (2x)
6
Connecting plate (1x)
7
Screw (4x)
4.2 Not in scope of delivery
8
9
Fig.2
8
Mini slide (1x)
DGSS
9
Shock absorber (2x)
DYEF-G8/DYSS-G8
5 Product design
Z
Z
Y
Fig. 3: Product design
Y
Axial air connections
Z
Thread for shock absorber
6 Assembly
1
A
B
2
Fig. 4: Pushing in stop
1. Extend the slide[A] manually.
2. Slide the stop into the slot[B].2
3. Insert the screws into the holes of the stop .1 2
4. Slide the stop to the end of the slot[B].2
A
C
1
Fig. 5: Mounting stop
1. Position the slide[A] so hole[C] is aligned with a screw .1
2. Tighten the screw . Observe the tightening torque.1
DADP-SP-G9 -6 -10 -16 -20
Screw M2 x 6 M2.5 x 8 M2.5 x 8 M3 x 12
[Nm] 0.3 ±15% 0.5 ±15% 0.7 ±15% 0.9 ±15%
3. Repeat this process for the second screw .1
C
3
Fig. 6: Note the stop bar
When installing the stop element , note the position of the stop bar[C].3
3
D
A
Fig. 7: Aligning stop element
1. Retract the slide[A] manually.
2. Position the upper edge of the stop element at the level of the thread[D].3
3
A
C
Fig. 8: Attaching stop bar
1. Push the stop element upwards to the stop.3
ÄThe stop bar[C] is in contact with the slide[A].
2. Hold this position.
4
3A
Fig. 9: Mounting stop element
Mount the stop element on the slide[A] with the screws . Observe the3 4
tightening torque.
DADP-SP-G9 -6 -10 -16 -20
Screw M2 x 8 M2.5 x 10 M3 x 10 M4 x 12
[Nm] 0.4 ±15% 0.9 ±15% 1.4 ±15% 2.0 ±15%
5
X
Fig. 10: Sealing air connections
Insert the O-rings into the holes[X].5
68
7
Fig. 11: Mounting sub-base
Mount the sub-base on the mini slide with the screws . Observe the6 8 7
tightening torque.
DADP-SP-G9 -6 -10 -16 -20
Screw M2 x 14 M2.5 x 18 M3 x 16 M4 x 22
[Nm] 0.3 ±15% 0.8 ±15% 0.8 ±15% 1.5 ±15%

Produktspecifikationer

Varumärke: Festo
Kategori: Inte kategoriserad
Modell: DADP-SP-G9-20-R

Behöver du hjälp?

Om du behöver hjälp med Festo DADP-SP-G9-20-R ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Festo Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer