Fluke LVD2 Bruksanvisning

Läs nedan 📖 manual på svenska för Fluke LVD2 (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/3
LVD2
VoltAlert
Safety Sheet
Read First: Safety Information
WX Warning
To prevent possible electric shock, fi re, or personal injury:
Use the Product only as speci ed, or the protection supplied by the Product
can be compromised.
Do not rely on the Product to detect the presence or absence of voltage on
a conductor for safety purposes. A single pole non-contact voltage detector
such as this Product is not suitable to determine if a circuit is hazardous. A
volt meter or 2-pole voltage detector is necessary to confi rm the absence of
hazardous voltage prior to commencing work.
Do not use if the fl ashlight does not operate.
Detect a known voltage fi rst to make sure that the Product operates correctly.
When using the Product if tip does not glow, voltage could still be present.
The Product indicates active voltage in the presence of electric fi elds of
suffi cient strength generated from the source (MAINS) voltage. If the fi eld
strength is low, the Product may not provide indication of live voltages. Lack
of an indication occurs if the Product is unable to sense the presence of
voltage which may be infl uenced by several factors including, but not limited
to:
Shielded wire/cables
Thickness and type of insulation
Distance from the voltage source
Fully-isolated users that prevent an eff ective ground
Receptacles in recessed sockets/ diff erences in socket design
Condition of the Product and Batteries
Disable the Product if it is damaged.
Do not use the Product if it is damaged.
Use Product with arrow visible.
Hold the Product behind the tactile barrier.
Do not use for dc voltage detection or around voltages exceeding
600 volts, or in the presence of variable motor drives.
Use caution with voltages above 30 V ac as a shock hazard may exist.
Do not stare or look directly at the LED fl ash light. The light is extremely
bright.
Comply with local and national safety codes. Use personal protective
equipment (approved rubber gloves, face protection, and fl ame-resistant
clothes) to prevent shock and arc blast injury where hazardous live
conductors are exposed.
Batteries contain hazardous chemicals that can cause burns or explode. If
exposure to chemicals occurs, clean with water and get medical aid.
Remove the batteries if the Product is not used for an extended period of time,
or if stored in temperatures above 50 °C. If the batteries are not removed,
battery leakage can damage the Product.
Carefully read all instructions.
Read all safety information before you use the Product.
PN 4572337 September 2014 Rev. 1, 10/19
© 2014 -2019 Fluke Corporation. Specifi cations are subject to change without notice.
All rights reserved.
FOR USE BY COMPETENT
PERSONS
Anyone using this instrument should be
knowledgeable and trained about the risks
involved with measuring voltage, especially
in an industrial setting, and the importance of
taking safety precautions and of testing the
instrument before and after using it to ensure
that it is in good working condition.
For safe operation and maintenance of the product:
Be sure that the battery polarity is correct to prevent battery leakage.
Repair the Product before use if the battery leaks.
Symbols
Consult user documentation.
TDouble Insulated.
XHazardous Voltage. Risk of electric shock.
WRisk of danger. Important information.
PConforms to European Union directives
)Conforms to relevant Canadian and US Standards.
Conforms to relevant Australian standards.
~This product complies with the WEEE Directive (2002/96/EC) marking
requirements. The affi xed label indicates that you must not discard this
electrical/electronic product in domestic household waste. Product Category:
With reference to the equipment types in the WEEE Directive Annex I, this
product is classed as category 9 “Monitoring and Control Instrumentation”
product. Do not dispose of this product as unsorted municipal waste. Go to
Fluke’s website for recycling information.
CAT IV Measurement Category IV is applicable to test and measuring circuits
connected at the source of the building’s low-voltage MAINS installation.
Battery
Safety Speci cations
Altitude ....................................2000 m
Humidity ..................................80 % for temperatures up to 31 °C decreasing
linearly to 45 % relative humidity at 50 °C
Electrical supply .....................1.5 Vdc (1 x LR03 ‘AAA Battery)
Temperature ............................0 °C to 50 °C
Maximum Voltage to Earth
Ground ....................................600 V
Safety .......................................IEC61010-1:Pollution Degree 2. CAT IV 600V
Electromagnetic
Compatibility .......................... (EMC) IEC 61326-1: Portable Electromagnetic
Environment; IEC 61326-2-2
CISPR 11: Group 1, Class A
Group 1: Equipment has intentionally generated and/or use
conductively coupled radio-frequency energy which is necessary for the
internal functioning of the equipment itself.
Class A: Equipment is suitable for use in all establishments other than
domestic and those directly connected to a low voltage power supply
network which supplies buildings used for domestic purposes. There
may be potential di culties in ensuring electromagnetic compatibility in
other environments, due to conducted and radiated disturbances.
Caution: This equipment is not intended for use in residential
environments and may not provide adequate protection to radio
reception in such environments
Contacting Fluke
Technical Support USA: 1-800-44-FLUKE (1-800-443-5853)
Calibration/Repair USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Anywhere in the world: +1-425-446-5500
Or, visit Fluke’s website at www.fl uke.com.
To register your product, visit http://register.fl uke.com.
To view, print, or download the latest manual supplement, visit
http://us.fl uke.com/usen/support/manuals.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and workmanship for two years from
the date of purchase. This warranty does not cover fuses, disposable batteries, or damage
from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation
or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To
obtain service during the warranty period, contact your nearest Fluke authorized service center
to obtain return authorization information, then send the product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS
FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do
not allow the exclusion or limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090 U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
11/99

Produktspecifikationer

Varumärke: Fluke
Kategori: Inte kategoriserad
Modell: LVD2

Behöver du hjälp?

Om du behöver hjälp med Fluke LVD2 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Fluke Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer