Frigidaire IMKTTM0018 Bruksanvisning

Frigidaire Inte kategoriserad IMKTTM0018

Läs nedan 📖 manual på svenska för Frigidaire IMKTTM0018 (7 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

AUTOMATIC ICE MAKER

INSTALLATION INSTRUCTIONS

P/N: A23224101

WARNING

• To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator

from electrical power before connecting a water supply line to the refrigerator.

• Connect the ice maker to a potable water supply only.

An authorized service technician is recommended to install the ice maker kit.

Ice Maker (IMKTTM0018) Kit Components

5304520536

Ice Maker

QTY: 1

5304525288

Shoulder Screw

QTY: 5

5304520538/5304520539

Cover with Door

QTY: 1

5304520535

Ice Bin

QTY: 1

Parts needed for install inside the unit

Tools Needed:

• Flat head screw driver • Phillips or Quadrex driver

• ¼" Hex driver • Gloves

• Drill • Needle nose pliers

Parts needed for install on back side of the unit

NOTE

Check with your local building authority for recommendations on water lines and associated materials prior

to installing your new refrigerator. For household water line hookup from the home water supply system to

the unit, we recommend for homes with existing valves Smart Choice® water line kit 5304437642 (with a 6'

Stainless Steel Water Line) and for homes without an existing valve, we recommend Smart Choice® water

line kit 5304493869 (with a 6' Polyline Waterline). Please refer to Frigidaire.com for more information.

5304520540

Water Valve

QTY: 1

218976923

Tube

QTY: 1

241500304

#8 screw

QTY: 2

5304455846

Clamp " ¼

QTY: 1

5303001193

Clamp "½

QTY: 1

A22628901

Fill Tube

QTY: 1

A23297701

Screw

QTY: 2

A23221901

Foam Pad

QTY: 1

A23222001

Foam

Rectangle

QTY: 1

Fill Tube Kit

A23489801/2107000021

Ice Maker Installation Instructions

1. Unplug refrigerator from electrical outlet.

2. Lift the freezer shelf up and out. Set aside.

See Figure 1.

3. Remove water inlet and electrical cover, located

on the inside of the unit, by inserting a ﬂathead

screwdriver on right side of opening in the small

cover. Push to the left to disengage the snap.

See Figure 2

4. Locate dimples in the freezer liner for screw

placement (a ﬂashlight may help). Align the

shoulder screws with the dimples. Push the

screws to penetrate the freezer liner and drive the

screws in until they are tight against the liner. Use

2 screws on the left side wall, and 3 on the top of

the liner. See Figure 3.

5. Insert the ice maker connector and wire through

the hole in the middle of the water inlet and

electrical cover. See Figure 4.

Slide the ice maker onto the 2 side wall shoulder

screws. The ice maker will snap into place.

See Figure 6.

6. Plug the ice maker in the electrical connector

on the back wall. Then install the water inlet and

electrical cover back in position by inserting the

tab on the left side into the slot and push in the

right side to make the snap engage. See Figure 5.

Figure 1

Figure 2

To Ceiling

To Wall

Install 5

Shoulder

Screws

Figure 3

Figure 4

Align Water

Inlet

Plug

Electrical

Connector

Figure 5

Figure 6

Ice Maker Installation Instructions

8. Locate the Ice maker installation label on the

rear outside right top corner of the refrigerator.

Cut the label on the dashed lines, and push ﬂaps

inward until they stick to the unit. See Figure 9.

Align the ﬁll tube key to the slot. Insert the ﬁll

tube with foam pads. Drive the 2 screws to ﬁx the

ﬁll tube against the refrigerator. See Figure 10.

7. Remove the silicone paper on the foam pads.

Stick the ring shaped foam pad to the ﬁll tube.

See Figure 7.

Make sure the end of water ﬁll tube sits within the

water channel of the ice maker. See Figure 11.

9. Slide the ice maker cover onto the shoulder

screws on top of the unit until it locks into place

with a snap. See Figure 12.

Wrap the rectangular foam pad around the ﬁll

tube. See Figure 8.

Figure 7

Figure 8

Cut on dashed lines

and push in on flaps

Figure 9

Figure 10

Figure 12

Figure 11

Produktspecifikationer

Varumärke:	Frigidaire
Kategori:	Inte kategoriserad
Modell:	IMKTTM0018
Färg på produkten:	Zwart
Vikt:	1360 g
Höjd:	800 mm
Snäll:	Afzuigkap motor
Avgasanslutningsdiameter:	150 mm
Antal per paket:	1 stuk(s)