Frigidaire MWBOK15TB Bruksanvisning

Läs nedan 📖 manual på svenska för Frigidaire MWBOK15TB (15 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/15
Installation Bump-Out Kit
Instructions For 15” Deep Cabinets
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT:
Save these instructions for local inspector’s use.
Observe all governing codes and ordinances.
Note to Customer- Keep these instructions for future reference.
Skill level- Installation of this appliance requires basic mechanical
and electrical skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under
the Warranty.
Note to Installer Be sure to leave these
instructions with the consumer.
TOOLS YOU WILL NEED
# 1 P hillips screwdriver Penci l
Ruler or t ape measure and
straight edge Carpenter square
(optional)
Ti n snips (for cutti ng
damper, i f required)
Electric drill with 316
,12and58
drill bits
Hammer (opti onal)Stud finder or
Fi ll er blocks or scrap
wood pieces, i f ded nee
for top cabinet spacing
(used on recessed bott om
cabinet i nstallations only)
Gloves
Saw (saber, hole or keyhole)
Level Duct and masking t ape
Scissors
(to cut template, if necessary)
Safety goggles
MOUNTING SPACE NOTES:
The bet ween the cabinet s must be
30“(76.2 cm) wi de and free of obstr uctions.
If you are going to vent your microwave oven
to t he outside, see H ood Exhaust Section for
exhaust du ct p repar ati on .
When installing the microwave oven beneath
smooth, f lat cabinets, be caref ul to f ollow the
instr uctions on the top cabinet template f or
power cord clearance.
Bottom Edge of
Cabinet Needs to
be 30 (76.2 cm)
or More from the
Cooki ng Surface
Backsplash
66 (167.6 cm)
or more from
the oor to the
30 (76.2 cm)
2
(5.1 cm)
30
(76.2 cm)
min.
1612(41.9 cm)
Cabi netCabinet
NOTE: Maximum cabinet depth is 15
fl
top of the
microwave
acesp
''
''
''
''
''
A06823408
NOTE: For BOK installation use hardware from over the range microwave unit which has 2
toogle bolts and 2 wood screws for mounting BOK. In addition, there are 2 toggle bolts in the
BOK to complete proper installation.
Bump out kit installs with Over the Range models
in which the serial number of the unit begins with
To verify proper unit, check the rating
label located on the inside of the doo r.
See below example:
KGXXXXXXX.
KGXXXXXXXX
XXXXXXXXXX XXXXXX
Bump-Out Kit
Bracket
IMPORTANT:
C
  


  

   
 
 
  
 

 
     
 
 





 

 
 


Rear wall template
Installation Instructions
DAMAGE SHIPMENT/INSTALLATION
If the unit is damaged in shipment, return the unit to the store in which it was bought for
repair or replacement
If the unit is damaged by the customer, repair or replacement is the responsibility of the
customer
If the unit is damaged by the installer (if other than the customer), repair or replacement
must be made by arrangement between customer and installer
Move the top cabinet template that comes with your OTR microwave
2. ” forward when installing from bac wall.
Use the rear wall template that comes with your OTR microwave to
identify mounting location for the bump out kit.
Move top cabinet template forward 2.2
Mark lowest edge of bracket
Place the Bump Out Kit Bracket in place of rear wall template location making sure that the bottom edge lines up.
5
2k
5
2
Installation Instructions
Find the studs, using one of the following methods:
A. Stud finder – a magnetic device which locates nails.
OR
B. Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate a stud
location.
After locating the stud(s), find the center by probing
the wall with a small nail to find the edges of the stud.
Then place a mark halfway between the edges. The
center of any adjacent studs should be 16" or 24" from
this mark.
Draw a line down the center of the studs.
THE BUMP-OUT BRACKET MUST BE ED
AT LEAST ONE
WALL STUD.
1
FINDING THE WALL STUDS
A.
2
PLACEMENT OF THE BUMP-OUT BRACKET
1
Wall Studs
Level line for front overhang
Center 3
B.
Centerline
notches Draw a Vertical Line
on Wall from Center
of Top Cabinet
Draw a horizontal line on wall at the
bottom of “Rear Wall Template”.
Horizontal Line
C
L
3/8" T O ED GE
%#76+10Ä+(':*#756#&#2614+5 215+6+10'& 1765+&'
4'%1//'0&'&&+/'05+ 10)4'#5'Ä.#&'0#+49+..
&+5%*#4)'+061*175'5647%674'
/+0+/7 /9+&6*4'37+4'&
4'#49#..6'/2.#6'
NOTE: IT IS VERY IMP ORTANT TO
READ AND FOLLOW THE DIRECTI ONS
IN THE IN STALLATI ON IN STRUCTIONS
BEFORE PROCEEDI NG WITH THIS
REAR WALL TEMPL ATE.
This Re ar Wall Te mplate s erve s to pos ition the bottom
mounting pla te a nd to locate the horizo ntal exhaus t
outlet.
1. Use a level to check tha t the te mpla te is pos itione d
a ccura tely.
2. Loca te a nd mark at le as t one s tud on the left or
right s ide of the ce nterline.
016 '
It is important to us e a t lea s t one wood
s crew mounte d firmly in a stud to support the we ight
of the microwave. Ma rk two add itional, eve nly spa ced
locations for the supplied toggle bolts.
3. Drill ho les in the marke d locations . Where the re is
a st ud, drill a 3/16" hole for wood s crews . For holes
that do not line up with a st ud, drill 5/8" holes for
toggle bolts .
016 '
DO NOT INSTALL T HE MOUNT ING PLAT E
AT T HIS TIME.
4. Remove the template from the re ar wa ll.
5. Review the Ins ta llation Ins truction book for your
insta llation situation.
Locate and mark hole s to align with h oles in the
mounting plat e .
IM PORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CEN TERLINE.
MARK TH E LOCATION FOR 2 ADDITIONAL , E VENLY
SPACED TOGGLE BOLTS IN TH E MOUNTIN G PLATE
AREA.
Locate and mark holes to align with hol es in the
mounting plat e.
IM PORTANT:
LOCATE AT LEAST ONE STUD ON EITHE R SIDE OF
THE CEN TERLINE.
MARK TH E LOCATION FOR 2 ADDITIONAL , E VENLY
SPACED TOGGLE BOLTS IN THE M OUN TING PLATE
AREA.
T rim the rea r wall tem pla te a long the do tted lin e.
%
#
$%
&
(%76176(14*14+<106#.
1765+&'':*#756
%76*1.'6*417)* 4'#4 9#.. (14':*#756#&#2614
12"
4"
Darle vue lta a la ho ja p ara c onsult ar la
ve rs ión e n Es pa ñol.
Draw a vertical line on the wall at the center of the
30" wide space.
1
2Draw a horizontal line on the wall at the bottom of
“Rear Wall Template”.
MARK THE LOWEST EDGE OF BRACKET
INSTALL IN
3

Produktspecifikationer

Varumärke: Frigidaire
Kategori: Inte kategoriserad
Modell: MWBOK15TB

Behöver du hjälp?

Om du behöver hjälp med Frigidaire MWBOK15TB ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Frigidaire Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer