Fujitsu ASGA18FUTC-B Bruksanvisning

Fujitsu Splitter ASGA18FUTC-B

Läs nedan 📖 manual på svenska för Fujitsu ASGA18FUTC-B (12 sidor) i kategorin Splitter. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

En-1

Note: This manual describes how to install the air conditioner described above. Handling

and installation shall only be done by professionals as outlined in this manual.

1. SAFETY PRECAUTIONS

x Be sure to read this manual thoroughly before installation.

x The warnings and precautions indicated in this manual contain important informa-

tion pertaining to your safety. Be sure to observe them.

x Hand this manual, together with the operating manual, to the customer. Request

the customer to keep them on hand for future use, such as for relocating or repair-

ing the product.

WARNING Indicates a potentially or imminently hazardous situation which,

if not avoided, could result in death or serious injury.

Installation of this product must be done by experienced service technicians

or professional installers only in accordance with this manual. Installation by

nonprofessional or improper installation of the product may cause serious accidents

such as injury, water leakage, electric shock, or fire. If the product is installed in

disregard of the instructions in this Manual, it will void the manufacturer’s warranty.

Do not turn on the power until all work has been completed. Turning on the power before

WKHZRUNLVFRPSOHWHGFDQFDXVHVHULRXVDFFLGHQWVVXFKDVHOHFWULFVKRFNRU¿UH

If refrigerant leaks when you are working, ventilate the area. If the leaking refrigerant is

H[SRVHGWRDGLUHFWÀDPHLWPD\SURGXFHDWR[LFJDV

'RQRWXVHWKLVHTXLSPHQWZLWKDLURUDQ\RWKHUXQVSHFL¿HGUHIULJHUDQWLQWKHUHIULJHUDQW

lines. Excess pressure can cause a rupture.

Installation must be performed in accordance with regulations, codes, or standards for

electrical wiring and equipment in each country, region, or the installing place.

'RQRW WRXFKWKH ¿QVRI WKHKHDW H[FKDQJHU7RXFKLQJWKH KHDWH[FKDQJHU ¿QV FRXOG

UHVXOWLQGDPDJHWRWKH¿QVRUSHUVRQDOLQMXU\VXFKDVVNLQUXSWXUH

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. Children should be supervised to ensure that they do

not play with the appliance.

CAUTION Indicates a potentially hazardous situation that may result in

minor or moderate injury or damage to property.

Read carefully all safety information written in this manual before you install or use the

air conditioner.

Install the product by following local codes and regulations in force at the place of

installation, and the instructions provided by the manufacturer.

This product is part of a set constituting an air conditioner. The product must not be

installed alone or be installed with non-authorized device by the manufacturer.

Always use a separate power supply line protected by a circuit breaker operating on all

wires with a distance between contact of 3 mm for this product.

To protect the persons, earth (ground) the product correctly, and use the power cable

combined with an Earth Leakage Circuit Breaker (ELCB).

The product is not explosion proof, and therefore should not be installed in explosive

atmosphere.

To avoid getting an electric shock, never touch the electrical components soon after the

power supply has been turned off. After turning off the power, always wait 5 minutes or

more before you touch the electrical components.

This product contains no user-serviceable parts. Always consult experienced service

technicians for repairing.

When moving or relocating the air conditioner, consult experienced service technicians

for disconnection and reinstallation of the product.

Do not place any other electrical products or household belongings under the product.

Condensation dripping from the product might get them wet, and may cause damage or

malfunction of the property.

2. ABOUT THIS PRODUCT

2.1. Precautions for using R410A refrigerant

The basic installation work procedures are the same as conventional refrigerant (R22)

models.

However, pay careful attention to the following points:

Since the working pressure is 1.6 times higher than that of conventional refrigerant (R22)

models, some of the piping and installation and service tools are special. (See the table

below.)

Especially, when replacing a conventional refrigerant (R22) model with a new refrigerant

5$PRGHODOZD\VUHSODFHWKHFRQYHQWLRQDOSLSLQJDQGÀDUHQXWVZLWKWKH5$

SLSLQJDQGÀDUHQXWV

Models that use refrigerant R410A have a different charging port thread diameter

to prevent erroneous charging with conventional refrigerant (R22) and for safety.

Therefore, check beforehand. [The charging port thread diameter for R410A is

1/2-20 UNF]

Be more careful that foreign matter (oil, water, etc.) does not enter the piping than with

refrigerant (R22) models. Also, when storing the piping ,securely seal the opening by

pinching, taping, etc.

When charging the refrigerant, take into account the slight change in the composition of

the gas and liquid phases. And always charge from the liquid phase where refrigerant

composition is stable.

2.2. Special tools for R410A refrigerant

Tool name Changes

Gauge manifold

Pressure is high and cannot be measured with a conventional

(R22) gauge. To prevent erroneous mixing of other refriger-

ants, the diameter of each port has been changed.

It is recommended to use the gauge with seals-0.1 to 5.3 MPa

(-1 to 53 bar) for high pressure.

-0.1 to 3.8 MPa (-1 to 38 bar) for low pressure.

Charge hose To increase pressure resistance, the hose material and base

size were changed.

Vacuum pump A conventional vacuum pump can be used by installing a

vacuum pump adapter.

Gas leakage detector Special gas leakage detector for HFC refrigerant R410A.

Copper pipes

It is necessary to use seamless copper pipes and it is desirable that the amount of re-

sidual oil is less than 40 mg/10 m. Do not use copper pipes having a collapsed, deformed

or discoloured portion (especially on the interior surface). Otherwise, the expansion value

or capillary tube may become blocked with contaminants.

As an air conditioner using R410A incurs pressure higher than when using R22, it is neces-

sary to choose adequate materials.

AIR CONDITIONER

INDOOR UNIT (Wall Mounted Type) INSTALLATION MANUAL

PART No. 9387082241

For authorized service personnel only.

Refer to the rating label with the serial number.

Contents

1. SAFETY PRECAUTIONS ................................................................. 1

2. ABOUT THIS PRODUCT.................................................................. 1

3. GENERAL SPECIFICATION ............................................................ 2

4. SELECTING THE INSTALLATION LOCATION ................................ 3

5. INSTALLATION WORK .................................................................... 3

6. ELECTRICAL WIRING ..................................................................... 5

7. FINISHING........................................................................................ 6

8. FRONT PANEL REMOVAL AND INSTALLATION ........................... 7

9. REMOTE CONTROLLER INSTALLATION ....................................... 7

10. OPTIONAL KIT INSTALLATION ....................................................... 8

11. FUNCTION SETTING...................................................................... 8

12. CHECK LIST ..................................................................................... 9

13. TEST RUN ........................................................................................ 9

14. CUSTOMER GUIDANCE ................................................................. 9

15. ERROR CODES ............................................................................ 10

English

En-2

CONNECTION PIPE REQUIREMENT

WARNING

'RQRWXVHWKHH[LVWLQJIRU5SLSLQJDQGÀDUHQXWV

If the existing materials are used, the pressure inside the refrigerant cycle will rise

and cause failure, injury, etc. (Use the special R410A materials.)

When installing and relocating the air conditioner, do not mix gases other

WKDQWKHVSHFL¿HGUHIULJHUDQW5$WRHQWHUWKHUHIULJHUDQWF\FOH

If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise

to an abnormally high value and cause failure, injury, etc.

2.3. Accessories

The following installation accessories are supplied. Use them as required.

Name and Shape Q’ty Name and Shape Q’ty

Operating Manual

Remote controller

holder

Installation Manual

Insulation (Drain hose)

6SHFL¿FDWLRQ0DQXDO

Cloth tape

Wall hook bracket

Tapping screw (large)

Remote controller

Tapping screw (small)

Battery

2.4. Optional parts

Refer to each installation manual for the method of installing optional parts.

Parts name Model No. Application

Wired Remote Controller* UTY-RNN*M For air conditioner operation

$SSOHFDWHFKLQ¿OWHU UTR-FA13-1

,RQGHRGRUL]DWLRQ¿OWHU UTR-FA13-2

External connect kit* UTY-XWZXZ5 For control input/output port

Communication kit UTY-XCBXZ3 For the installation of optional

parts

* Optional communication kit is necessary for the installation.

2.5. Additional materials required for installation

The following items are necessary to install this air conditioner. (The items are not includ-

ed with the air conditioner and must be purchased separately.)

Name

Connection pipe assembly Saddle

Connection cable Drain hose

Wall pipe Tapping screws

Decorative tape Sealant

Vinyl tape M10 bolt, nut

Wall cap

3. GENERAL SPECIFICATION

This Installation manual briefly outlines where and how to install the air conditioning

system. Please read over the entire set of instructions for the indoor and outdoor units and

make sure all accessory parts listed are with the system before beginning.

3.1. Type of copper pipe and insulation material

CAUTION

Refer to the installation manual for the outdoor unit for description of allowable pipe

length and height difference.

Diameter

Liquid pipe Gas pipe

30/36 type 9.52 mm (3/8 in.) 15.88 mm (5/8 in.)

18/24 type 6.35 mm (1/4 in.) 15.88 mm (5/8 in.)

CAUTION

Install heat insulation around both the gas and liquid pipes. Failure to do so may cause

water leaks.

Use heat insulation with heat resistance above 120 °C. Reverse cycle model only

In addition, if the humidity level at the installation location of the refrigerant piping is

expected to exceed 70%, install heat insulation around the refrigerant piping. If the

expected humidity level is 70-80%, use heat insulation that is 15 mm or thicker and if the

expected humidity exceeds 80%, use heat insulation that is 20 mm or thicker.

,IKHDWLQVXODWLRQLVXVHGWKDWLVQRWDVWKLFNDVVSHFL¿HGFRQGHQVDWLRQPD\IRUPRQWKH

surface of the insulation. In addition, use heat insulation with heat conductivity of

:P.RUOHVVDW&

3.2. Electrical requirement

The indoor unit is powered from the outdoor unit or branch box. Do not power indoor unit

from separate power source.

WARNING

Refer to local codes for acceptable cable type.

Cable

Cable size (mm

)

Type

Remarks

Connection cable

1.5 ~ 2.5 Type 60245 IEC 57 *Refer to “Outdoor unit installation

manual”

Max. Cable Length: Limit voltage drop to less than 2%. Increase cable gauge if voltage

drop is 2% or more.

 Before starting work check that power is not being supplied to all poles of the indoor

unit and outdoor unit.

 Install all electrical works in accordance to standard.

 Install the disconnect device with a contact gap of at least 3mm in all poles nearby the

units. (Both indoor unit and outdoor unit)

 Wiring size must comply with the applicable local and national code.

En-3

4. SELECTING THE INSTALLATION LOCATION

Decide the mounting position with the customer as follows:

WARNING

Select installation locations that can properly support the weight of the indoor unit

and which will not amplify sound or vibration. If the installation location is not strong

enough, the indoor unit may fall and cause injuries.

Install the units securely so that they do not topple or fall.

CAUTION

Do not install the unit in the following areas:

$UHDZLWKKLJKVDOWFRQWHQWVXFKDVDWWKHVHDVLGH,WZLOOGHWHULRUDWHPHWDOSDUWV

causing the parts to fail or the unit to leak water.

$UHD¿OOHGZLWKPLQHUDORLORUFRQWDLQLQJDODUJHDPRXQWRIVSODVKHGRLORUVWHDP

such as a kitchen.

It will deteriorate plastic parts, causing the parts to fail or the unit to leak water.

$UHDWKDWJHQHUDWHVVXEVWDQFHVWKDWDGYHUVHO\DIIHFWWKHHTXLSPHQWVXFKDV

sulphuric gas, chlorine gas, acid, or alkali.

It will cause the copper pipes and brazed joints to corrode, which can cause

refrigerant leakage.

$UHDWKDWFDQFDXVHFRPEXVWLEOHJDVWROHDNFRQWDLQVVXVSHQGHGFDUERQ¿EUHVRU

ÀDPPDEOHGXVWRUYRODWLOHLQÀDPPDEOHVVXFKDVSDLQWWKLQQHURUJDVROLQH

,IJDVOHDNVDQGVHWWOHVDURXQGWKHXQLWLWFDQFDXVHD¿UH

$UHDZKHUHDQLPDOVPD\XULQDWHRQWKHXQLWRUDPPRQLDPD\EHJHQHUDWHG

Do not use the unit for special purposes, such as storing food, raising animals, growing

plants, or preserving precision devices or art objects.

It can degrade the quality of the preserved or stored objects.

Do not install where there is the danger of combustible gas leakage.

'RQRWLQVWDOOWKHXQLWQHDUDVRXUFHRIKHDWVWHDPRUÀDPPDEOHJDV

Install the unit where drainage does not cause any trouble.

Install the unit where ambient temperature does not reach 60°C or more. Take a

measure such as ventilation for an environment in which heat is retained.

If children under 10 years old may approach the unit, take preventive measures so

that they cannot reach the unit.

,QVWDOOWKHLQGRRUXQLWRQWKHZDOOZKHUHWKHKHLJKWIURPWKHÀRRUVPRUHWKDQP

(1) Install the indoor unit level on a strong wall which is not subject to vibration.

(2) The inlet and outlet ports should not be obstructed: the air should be able to blow all

over the room.

(3) Install the unit at a place near an power outlet or special branch circuit.

(4) Do not install the unit where it will be exposed to direct sunlight.

(5) Install the unit where connection to the outdoor unit is easy.

(6) Install the unit where the drain pipe can be easily installed.

(7) Take servicing, etc. into consideration and leave the spaces shown in “5.1. Installation

GLPHQVLRQV´$OVRLQVWDOOWKHXQLWZKHUHWKH¿OWHUFDQEHUHPRYHG

&RUUHFWLQLWLDOLQVWDOODWLRQORFDWLRQLVLPSRUWDQWEHFDXVHLWLVGLI¿FXOWWRPRYHXQLWDIWHULWLV

installed.

5. INSTALLATION WORK

5.1. Installation dimensions

(Wall cap)

1.5 m or over

60 mm or over**

80 mm or over* Wall hook bracket

130 mm

or over**

1.8 m or over

* The distance between the wall hook

bracket and the ceiling should be

80 mm or more.

** The side next to the sidewall must

IROORZWKHVL]HLQGLFDWHGLQ¿JXUH

5.2. Indoor unit piping direction

7KHSLSLQJFDQEHFRQQHFWHGLQWKHGLUHFWLRQVLQWKH¿JXUH:KHQWKHSLSLQJLVFRQ-

nected in direction (B), (C), (D) or (E), cut along the piping groove in the side of the front

panel with a hacksaw.

(B) Right

outlet (A) Rear

outlet

(D) Left bottom

outlet

(E) Left

outlet

(Rear)

(F) Centre

outlet

(G) Left rear

outlet

5.3. Cutting the hole in the wall for the connecting pipes

&XWDPPGLDPHWHUKROHLQWKHZDOODWWKHSRVLWLRQVKRZQLQWKH¿JXUH

(2)

When cutting the wall hole at the inside of the wall hook bracket, cut the hole to a point of

intersection of centre marks.

When cutting the wall hole at the outside of the wall hook bracket, cut the hole at a

point of 10 mm below.

(3) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end.

(4) Always align the centre of the wall hole. If misaligned, water leakage will occur.

(5) Cut the wall pipe to match the wall thickness, stick it into the wall cap, fasten the cap

with vinyl tape, and stick the pipe through the hole.

)RUOHIW SLSLQJDQGULJKWSLSLQJ FXW WKHKROH DOLWWOHORZHU VRWKDWGUDLQZDWHUZLOOÀRZ

freely.

Wall hook bracket Centring marks

LowerLower

10 mm

or more

80 mm hole 10 mm

or more

Fasten with vinyl tape

5~10 mm

Wall pipe

(Field supply)

Wall cap

(Field supply)

(Inside) (Outside)

Wall

80 mm hole

WARNING

If the wall pipe is not used, the cable interconnecting the indoor unit(s) and outdoor unit

or branch box may touch metal and cause electric discharge.

5.4. Installing the wall hook bracket

(1) Install the wall hook bracket so that it is correctly positioned horizontally and vertically.

,IWKHZDOOKRRNEUDFNHWLVWLOHGZDWHUZLOOGULSWRWKHÀRRU

(2) Install the wall hook bracket so that it is strong enough to support the weight of the

unit.

Ɣ 

Fasten the wall hook bracket to the wall with 6 or more screws through the holes near the

outer edge of the bracket

Ɣ &KHFNWKDWWKHUHLVQRUDWWOHDWWKHZDOOKRRNEUDFNHW

Wall hook bracket Tapping screw (large)

(Accessory, 8 pcs)

CAUTION

Install the wall hook bracket by levelling, both horizontally and vertically.

Produktspecifikationer

Varumärke:	Fujitsu
Kategori:	Splitter
Modell:	ASGA18FUTC-B

Behöver du hjälp?

Om du behöver hjälp med Fujitsu ASGA18FUTC-B ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Splitter Fujitsu Manualer

Fujitsu ARYG24LHTBP Bruksanvisning

4 Oktober 2024

Fujitsu ASYG14LUCA Bruksanvisning

3 Oktober 2024

Fujitsu Standard ASHG24KMTB Bruksanvisning

30 September 2024

Fujitsu ECO ASHG18KLCA Bruksanvisning

29 September 2024

Fujitsu Designer ASHG07KETA-B Bruksanvisning

29 September 2024

Fujitsu ASYG24LFCC Bruksanvisning

27 September 2024

Fujitsu ASEG18KMTE Bruksanvisning

26 September 2024

Fujitsu ASEG24KMTE Bruksanvisning

26 September 2024

Fujitsu ASEH30KMTB Bruksanvisning

26 September 2024

Fujitsu ASEH36KMTB Bruksanvisning

26 September 2024

Splitter Manualer

Nyaste Splitter Manualer

Smart-AVI HDS-8P Bruksanvisning

23 Oktober 2024

IFM E43406 Bruksanvisning

17 Oktober 2024

Tripp Lite B155-004-HD-V2 Bruksanvisning

7 Oktober 2024

Zipper ZI-HS30Z Bruksanvisning

5 Oktober 2024

Tripp Lite B156-002 Bruksanvisning

2 Oktober 2024

D-Link DPE-301GS Bruksanvisning

29 September 2024

Audio-Technica ATW-49SP Bruksanvisning

27 September 2024

Samsung AM018FNNDCH Bruksanvisning

25 September 2024

Samsung AM018FNCDCH Bruksanvisning

25 September 2024

Samsung AM048TXMDCH Bruksanvisning

25 September 2024