Fujitsu AXGS18FHTA-U Bruksanvisning

Fujitsu Luftkonditionering AXGS18FHTA-U

Läs nedan 📖 manual på svenska för Fujitsu AXGS18FHTA-U (2 sidor) i kategorin Luftkonditionering. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

ROOM AIR CONDITIONER

ENGLISH

P/N 9386269100

Before using this product, read these instructions thoroughly and keep this manual for future reference.

To prevent personal injury, injury to others, or property damage, read this section carefully before you use this product, and be sure to comply following

safety precautions.

Incorrect operation due to failure to follow the instructions may cause harm or damage, the seriousness of which is classiﬁ ed as follows:

Refer to the rating label with the serial number.

MADE IN THAILAND

OPERATION MANUAL

Safety Precautions

Care and Maintenance Installation

Troubleshooting

CAUTION

lDuring maintenance, be sure to place the removed components in a safe place to avoid damage to them.

lDo not touch the aluminum ﬁ ns of heat exchanger built-in the indoor or outdoor unit to avoid personal injury when you install or maintain the unit.

Also, pay attention not to be scratched or pinched your hand by inner parts.

lNever use water hotter than 40 °C. The unit body may warp or change color.

lDo not use inﬂ ammable sprays such as lacquer or hair spray near the air conditioner.

The unit can be damaged by gasoline, benzine, thinners, insecticides and other chemical agents.

lBefore cleaning the unit, be sure to turn it off and all the power supply has been disconnected.

Cleaning the Air Filter

If dirt is allowed to collect in the air ﬁ lter, the airﬂ ow will be reduced, leading to reduced performance, and increased operating noise. Be sure to clean the

ﬁ lters at the beginning of the operating season, and about every 2 weeks during periods of frequent operation.

The air ﬁ lter is attached to the front panel, and you need to remove the intake grille ﬁ rst, when you get access to the air ﬁ lter.

Cleaning the unit

Clean the unit by wiping with a cloth moisten with cool or warm water, then wipe with another soft, clean, and dry cloth.

When not using the unit for extended periods (1 month or more)

Operate the unit on fan mode for about one-half day on a day with clear weather, to assure that the internal parts are dry.

When not using the unit for extended periods, turn off the electrical breaker or disconnect the power plug for safety.

Check the power cord

lRemove the built-up dirt and dust on the power plug and the electrical outlet periodically.

lCheck the power cord occasionally to conﬁ rm that it is not damaged by cuts or abrasions. If you discover damage to the cord, consult authorized service

personnel.

Intake grille removal

Front panel removal

Air ﬁ lter cleaning

Front panel installation

Air ﬁ lter installation

Air ﬁ lter removal

Push the bottom of the intake grille up with your hand, and pull it toward you.

1. Remove one screw securing

the front panel.

2. Push the small projections on the bottom side of the front panel

upward to unlatch the lower side.

Then with holding up the front panel with your hands, remove it toward

you.

Use a vacuum cleaner to remove dust and dirt from the air ﬁ lter, or wash in

a synthetic detergent. After washing, dry in a shaded place, then reinstall.

1. Hook the upper edge of

the front panel (2 places)

to the unit.

2. Press the lower edge of the front panel, and secure it with the screw.

To attach the ﬁ lter to the front panel, with aligning the both sides of the ﬁ lter

to the front panel, insert the upper edge of the ﬁ lter to the rail on the front

panel. Then make sure that the lower edge of the ﬁ lter is ﬁ rmly inserted to

the rail too.

The air ﬁ lter can be installed either way up.

After attaching the air ﬁ lter, reinstall the intake grille.

With lifting up small tabs on the air ﬁ lter, pull the ﬁ lter toward you.

Inspections and repairs:

Depending on the conditions of use, the internal parts of an air conditioner will become dirty after about two or three season of use, and performance

may be affected. For this reason, regular professional maintenance is recommended. Consult authorized service personnel.

Controller Position Description

THERMOSTAT 1–10

As the knob is turned clockwise the

higher numbers on the dial indicate

lower temperature.

MASTER

CONTROL

(OFF) The air conditioner is switched off.

(FAN)

Fan only operates at MED speed,

without cooling room air is circulated

and cleaned.

(SUPER

QUIET)

Fan (Low speed) and compressor

operate at quiet cooling.

(NORMAL) Fan (Medium speed) and compressor

operate at intermediate cooling.

(HIGH

POWER)

Fan (High speed) and compressor

operate at rapid cooling.

SUPER WAVE

Horizontal airﬂ ow louvers continuously

change the direction of airﬂ ow. When

the master control knob is set to “OFF”,

the SUPER WAVE does not operate.

OFF

Horizontal airﬂ ow louvers stop enabling

airﬂ ow to be directed in any desired

direction.

Vertical airﬂ ow louvers

Horizontal airﬂ ow louvers

Air inlet

Front panel

Intake grille

Air ﬁ lter Power supply plug

Screw

Control panel

Operation

Unit Overview

Cooling

To obtain maximum cooling effect in the hot summer select position HIGH POWER on the master control. Maximum moisture removal, air circulation and

dust removal are effected at the same time.

Selection of SUPER QUIET reduces operating noise.

Air Circulation

An adequate ﬂ ow of air is very important for comfort. When the master control knob is set at “FAN” position, the fan only is actuated so that the air is ﬁ ltered

and circulated without cooling effect.

Air circulation only without cooling effect may also be achieved with the thermostat knob turned counterclockwise to “1” position and with the master control

at either “HIGH POWER” or “SUPER QUIET” position.

Thermostat Control

The thermostat is set by means of the thermostat control. When the room temperature is higher than the thermostat setting, the compressor is

automatically switched on to provide a cooling effect. When the room temperature is lower than the thermostat setting, the compressor is automatically

switched off to stop cooling.

It can be seen therefore, that the thermostat serves to keep the room temperature constant by causing the compressor to start and stop automatically.

1. When you wish to lower the temperature, turn the thermostat control clockwise in the direction of the higher numbers on the dial.

2. When you wish to increase the temperature, turn the thermostat control counterclockwise in the direction of the lower numbers.

3. When the thermostat is set at positions “5”, “6”, or “7”, comfortable room temperatures can usually be obtained. Note that it is unhealthy for the room

temperature to be lower than approximately 22 °C.

4. When the thermostat control is positioned at “10”, the room-side ﬁ n coil may freeze up due to excessively low room temperature caused by low outdoor

temperature at night.

Once the ﬁ n coil becomes frozen, the airﬂ ow from the air conditioner is restricted by the frost, and the room temperature may rise due to the resultant

weak cooling performance of the air conditioner.

5. The thermostat positions “8”, “9”, and “10” can be used when the room temperature does not become sufﬁ ciently low. This condition may occur when the

thermostat switches off automatically because cooled air, when it passes through the vertical airﬂ ow louvers positioned downwards and the horizontal

airﬂ ow louvers positioned to the left, makes a short circuit and the recirculated air touches the sensor of the thermostat.

Note: The thermostat controls the compressor only and accordingly the fan is constantly circulating air even during the period when the compressor is off.

Important: When restarting the cooling operation after it has been turned off by either master control of thermostat, be sure to allow at least 3 minutes.

If cooling operation is restarted immediately after it is turned off, an over current will ﬂ ow through the compressor motor and the safety

device will be actuated. If the safety device is actuated it will not be possible to restart the compressor motor for about 20 minutes.

Air Direction Control

When the SUPER WAVE switch is turned to “ON” position, the horizontal airﬂ ow louvers is automatically actuated and sweeps the jet of air alternately, left

and right and thus more effective cooling will be obtained.

The louvers may be stopped at any position when SUPER WAVE switch is turned off.

Installation dimension

Typical installation

Installation hole

455–460

Unit 455

Unit 710

600

or more

200

or more 200

or more

Wall

Unit: mm

Unit 670

Installation hole 670–673

Drain tube

(Outer diameter: 16)Φ

Condenser air inlet louvers Fit ﬂ ashing or insert caulking compound

behind top outside architrave.

Recommended architrave

57 mm (2 1/4”)×13 mm (1/2”)

tapering to 8 mm (5/16”)

typical all round on front and

rear of unit.

Timber frame–typical all

round on front and rear of

unit.

50 mm (2”)×6 mm (1/4”)

sponge rubber strip–typical

all round on front and rear

of unit.

Condenser air inlet louvers

must be completely clear of

outside architrave surface.

Front panel

Attach ﬁ eld supplied cabinet support brackets

to the cabinet and the wall, it is required.

5-10 mm

Recommended height:

750-1500 mm from the

ﬂ oor

In the event of a malfunction (burning smell, etc.), immediately

stop operation, turn off the electrical breaker or disconnect the

power plug, and consult authorized service personnel.

In the place where bears be sufﬁ cient to the weight of the air

conditioner concerning installation, noise and vibration choose

such place without increasing.

For installation, avoid any places in direct sunlight. Combined

installation with a sunshade is recommended; installing the unit

under direct sunlight may cause low cooling performance or

increasing of the electricity consumption.

Consult the installation in a special place to a selling agent.

Because sea breeze sometimes becomes to a cause of

malfunction by corrosion etc., in the case that the place become

use with machine oil, the place of many place etc., that occur,

sulfuration gas such as a hot spring area that hits in a seashore

area it buys and give consultation to that selling agent.

Avoid the neighbourhood that be discharged dust, a lampblack,

steam, such as an exhaust port, a ventilation fan.

It is place where do not give neighbours trouble about removal

water or a wind and noise.

Where practicable, locate the air conditioner with the lower edge

of the cabinet approximately 0.75 m (29.5”) to 1.5 m (59”) from

the ﬂ oor. This usually gives the optimum air circulation pattern

within the room for cooling and heating.

When installing the attached insulation (620 mm x 40 mm, t12),

insert it from the inside of the room so that the insulation ﬁ lls up

the gap between the rails on the inner bottom of the cabinet and

bottom side of the base.

Before requesting service, perform the following checks:

Symptom Problem

NORMAL

FUNCTIONS

Noise is heard: During operation and immediately after stopping the unit, the sound of water ﬂ owing in the air

conditioner’s piping may be heard. Also, noise may be particularly noticeable for about 2 to 3

minutes after starting operation (sound of coolant ﬂ owing).

During operation, a slight squeaking sound may be heard. This is the result of minute expansion and

contraction of the front cover due to temperature changes.

Smells: Some smell may be emitted from the unit. This smell is the result of room smells (furniture, tobacco,

etc.) which have been taken into the air conditioner.

Mist or steam are emitted: During cooling operation, a thin mist may be seen emitted from the unit. This results from the sudden

cooling of room air by the air emitted from the air conditioner, resulting in condensation and misting.

CHECK ONCE

Does not operate at all: Is the power plug disconnected from its outlet?

Has there been a power failure?

Has a fuse blown out, or a circuit breaker been tripped?

Poor cooling performance: Is the air ﬁ lter dirty?

Are the air conditioner’s intake grille or outlet port blocked?

Did you adjust the room temperature settings (thermostat) correctly?

Is there a window or door open?

In the case of cooling operation, is a window allowing bright sunlight to enter? (Close the curtains.)

In the case of cooling operation, are there heating apparatus or computers inside the room, or are

there too many people in the room?

If the problem persists after performing these checks, immediately stop operation, turn off the electrical breaker or disconnect the power plug, and consult

authorized service personnel.

Power Supply

WARNING

This mark warns of death or serious injury.

WARNING

lDo not attempt to install this air conditioner by yourself.

lThis unit contains no user-serviceable parts. Always consult authorized

service personnel for repairs.

lWhen moving, consult authorized service personnel for disconnection

and installation of the unit.

lDo not become over-exposed to cold air by staying in the direct path of

the air ﬂ ow of the air conditioner for extended periods of time.

lDo not insert ﬁ ngers or objects into the outlet port or intake grille.

lDo not start and stop air conditioner operation by turning off the

electrical breaker or disconnecting the power supply plug and so on.

lTake care not to damage the power supply cord.

lDo not modify the power cables, use extension cables, or use any

branches in the wiring. Improper connections, insufﬁ cient insulation, or

exceeding the allowable current can cause electric shock or ﬁ re.

lDo not bundle the power supply cable.

lIn the event of a malfunction (burning smell, etc.), immediately stop

operation, turn off the electrical breaker or disconnect the power

supply plug, and consult authorized service personnel.

lAlways turn off the electrical breaker or disconnect the power supply

plug whenever cleaning the air conditioner or the air ﬁ lter.

lThis appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person responsible

for their safety. Children should be supervised to ensure that they do

not play with the appliance.

lIf you see lightning or hear thunder, there might be a lightning

strike. To prevent electric shock hazard, stop the operation of the

air conditioner, and do not touch the unit or the power plug during

thunderstorm.

CAUTION

lProvide occasional ventilation during use.

lDo not direct airﬂ ow at ﬁ replaces or heating apparatus.

lDo not climb on, or place objects on the air conditioner.

lDo not hang objects from the unit.

lDo not set ﬂ ower vases or water containers on top of air conditioners.

lDo not expose the air conditioner directly to water.

lDo not operate the air conditioner with wet hands.

lDo not pull power supply cord.

lTurn off power source when not using the unit for extended periods.

lCheck the condition of the installation stand for damage.

lDo not place animals or plants in the direct path of the airﬂ ow.

lDo not drink the water drained from the air conditioner.

lDo not touch the aluminum ﬁ ns of heat exchanger built-in the indoor or

outdoor unit to avoid personal injury when you install or maintain the unit.

lDo not use in applications involving the storage of foods, plants or

animals, precision equipment, or art works.

lDo not apply any heavy pressure to radiator ﬁ ns.

lOperate only with air ﬁ lter installed.

lDo not block or cover the intake grille and outlet port.

lEnsure that any electronic equipment is at least 1 m away from the unit.

lAvoid installing the air conditioner near a ﬁ replace or other heating

apparatus.

lWhen installing the unit, take precautions to prevent access by infants.

lDo not use inﬂ ammable gases near the air conditioner.

CAUTION

This mark warns of injury or damage to property.

WARNING

lWiring connections must be performed by a qualiﬁ ed person in accordance with the speciﬁ cations. The voltage rating for this product is 220-240V at

50Hz. It should be operated with the range of 198 to 264V.

lThis air conditioner must be connected to a power source that has an electrical impedance of 0.164 or less or has a supply current of 100 A or Ω

greater. If the power supply does not meet the speciﬁ cations, contact the power company.

lIn order to enable efﬁ cient and trouble-free operation of your air conditioner, connect supply main of your air conditioner through an exclusive circuit,

having a time delay fuse, to the correct power supply described on the rating plate.

lThe circuit breaker with all pole disconnection must be incorporated in permanent wiring.

lIf the power supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualiﬁ ed persons in order to avoid a hazard.