Furuno SC50 Bruksanvisning

Furuno Inte kategoriserad SC50

Läs nedan 📖 manual på svenska för Furuno SC50 (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 10 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

SC50/110 Satellite Compass Operations and information Quick Guide

Specifications: 12-24 VDC (15 W), Heading [95%] (SC50) ±1.0°, (SC110) ±0.6°, follow-up: 45°/s rate-of-turn, settling time: ~4 minutes

Do not extend standard cables

;

LMR-400

(

to 60m

)

can also be used

;

label CABLE 1

(

BLK

CABLE 2

(

YELLOW

CABLE 3

(

RED

)

4.5-inch monochrome

LCD, 120 x 64 dots

Turning the Power On/Off

Use power switch on the processor unit to turn the power to the display unit on and off.

Panel Illumination, Display Contrast (64 levels)- press [DIM] key and omni-pad to adjust.

(If screen is blank, press [DIM] key then “▲” omni-pad key multiple times to adjust brilliance higher)

Display Modes - Steering, Nav Data, Set and Drift, Compass Rose, ROT, Heading (True only!)

DATUM settings - Confirm WGS84 (default), use when connected to an AIS and/or IMO compliant systems.

WAAS/DGPS Setup - Press the [MENU] key to open the menu. Make changes and press the [ENT] key.

OTHERS MENU

HOLD HDG DATA

• Allows displaying of last-used heading data at power on. Indicator flashes, noting un-reliable heading .

HDG RESTORATION

• Select GPS signal restore mode, automatically or manually, if lost. Manual restore requires key press.

HDG BACKUP

Select time to display backup data if the GPS signal is lost. This data is also output to external equipment.

Output sentence limitations - IEC 61162-1/2 format (typically compatible with NMEA sentences)

• The number of sentences that can be output depends on baud rate and output interval settings.

• The maximum number of characters per data sentence is shown in the table below.

• Sentences included are HDT, HDM, ROT, ATT, VDR, VTG, GGA, GNS GLL, VHW, VBW, HVE, ZDA

The number of characters that can be output “N” is calculated by the following formula:

N < 0.083 x T x B (Where T = Interval [in seconds] and B = Baud rate (4800 default), 9600, 19200 or 38400

Compliant with: IMO MSC. 116(73), ISO/FDIS 22090-3,IMO A. 694(17), IEC 60945 (2002-08), IEC 61162 (2000)

SC50/110 Operations and Information Quick Guide GP Page 1 3/7/2005

The processor is position sensitive -

Configuration is required; set [INST MENU] settings accordingly. (See manual; section 1.3)

Antenna Mounting - The antenna must be mounted above all other structures for an unobstructed view.

SC50/110

antenna

required horizontal seperation

1.5 meters 3 meters

10cm mast 30cm mast

Horizontal separation between antenna and structure

must be: 10 cm =1.5 m, 30 cm =3 m (minimum)

Distance increases for larger obstructions. See diagram

Failure to comply will cause multi-path reflection problems and heading loss (see “check install section”)

Confirming Satellite Status

Check the receiving condition of each antenna unit as follows:

• Press the [MENU] key to open the menu, select SATELLITE and press the [ENT] key.

• Use ◄ or ► to select between antenna elements to confirm receiving status.

• Press the [DISP] key to close the menu.

SC50/110 Operations and Information Quick Guide GP Page 2 3/7/2005

Position status North DOP RX signal level

(

lower is better

)

Bars that extend past first vertical line

are used in the headin

calculation

Elevation 5 °

(More accurate)

Antenna element no.

Troubleshooting: No RX signal on antenna 1, 2, or 3.

Switch antenna cable with one of the other known good

antennas to confirm antenna or processor problem

Elevation 45 °

(Less accurate)

Satellites

highlighted in

black used for

calculation

Checking Installation- multi-path and receive problems (re-confirm after adding any new near-by structures on the vessel)

Maintenance Menu Access - Press and hold [MENU] and [ENT] keys simultaneously (~ 8 sec.), at third beep release

[MENU] key first, then [ENT] key. Access [ANT MONI] from the maintenance menu and press [ENT].

Multipath Index for the baseline

between antenna 1 and antenna 3

Must be 1.5 or lower

Multipath Index for the baseline

between antenna 1 and antenna 2

Must be 1.5 or lower

Circular Graph displays (in 12 directions) tracking

error in relation to the vessel bow. The highest error

and its opposing direction are shown in black

(illustration shows error at 10 and 4 o’clock

position). Note: Two (2) sectors will always be

illuminated even when no heading loss is present

Bar Graph displays tracking error in 12 directions

Longer bars = more error (caused by obstacles)

Sectors opposite to obstacle may have most error

Elapsed time displays accumulated tracking data

(up to 99 hrs 59 mins). Collect a minimum 12 hrs

of data for valid information.

After confirming above information, turn the vessel in a complete circle to check for correct and stable heading

Produktspecifikationer

Varumärke:	Furuno
Kategori:	Inte kategoriserad
Modell:	SC50
Färg på produkten:	Roestvrijstaal
Bredd:	860 mm
Djup:	500 mm
Höjd:	175 mm
Förpackningens vikt:	5100 g
Förpackningens bredd:	900 mm
Djuppackning:	520 mm
Förpackningshöjd:	190 mm
Installationsfackets bredd:	840 mm
Installationsfack djup:	480 mm
Forma handfat:	Rechthoekig
Diskbänksmaterial:	Roestvrijstaal
Antal handfat:	1 kommen
Form första diskbänken:	Vierkant
Första skålens mått (BxL):	360 x 400 mm
Först kommer djupet:	175 mm
Kraangat:	Ja
Antal kranhål:	1
Disken:	Ja
Kran ingår:	Nee
Diskbänksstorlek:	3.5 "
Placera bänkskivan:	Links