GE JB620DRBB Bruksanvisning

GE Ugn JB620DRBB

Läs nedan 📖 manual på svenska för GE JB620DRBB (8 sidor) i kategorin Ugn. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•IMPORTANT — Save these

instructions for local inspector’s use.

•IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with consumer.

• Note to consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires a qualified installer or electrician.

•Proper installation is the responsibility of the

installer.

•Product failure due to improper installation is

not covered under warranty.

FOR YOUR SAFETY:

If you did not receive an anti-tip bracket with your purchase,

call 1-800-626-8774 to receive one at no cost. (In Canada,

call 1-800-561-3344.) For installation instructions of the bracket,

visit: www.geappliances.com. (In Canada, www.geappliances.ca.)

Installation Instructions

Free-Standing Electric Ranges

MATERIALS YOU MAY NEED TOOLS YOU WILL NEED

Anti-Tip Bracket

Kit Included

(UL Listed 40 AMP)

4-Wire Cord 4‘ long OR

3-Wire Cord 4‘ long

Squeeze Connector

(For Conduit

Installations Only)

REMOVE PACKAGING MATERIALS: Failure to remove packaging

materials could result in damage to the appliance. Remove all packing parts from oven,

racks, heating elements and drawer. Also, remove protective film and labels on the outer

door, cooktop and control panel.

Drill with 1/8” Bit

Safety Glasses

Adjustable Wrench

Level

Tin Snips

Tape Measure

Pliers

1/4” Nut Driver

Questions? Call 1-800-GE-CARES (1-800-432-2737) or visit www.geappliances.com

In Canada, call 1-800-

561-3344

or visit www.geappliances.ca

WARNING

—

Before

beginning the installation, switch

power off at service panel and

lock the service disconnecting

means to prevent power from

being switched on accidentally.

When the service disconnecting

means cannot be locked,

securely fasten a prominent

warning device, such as a tag,

to the service panel.

PREPARE THE OPENING (FOR INDOOR USE ONLY)

See illustrations for all rough-in and spacing dimensions. The range may be placed with 0”

clearance (flush) at the back wall and side walls of the cabinet.

21⁄

2”

21⁄

2”

71⁄2”

25”

”

3⁄

8”

7”

141⁄

2”

On models with baking

or warming drawers,

electrical outlet must

not be in this area.

31⁄

4”

31⁄

4”

73⁄4”

231⁄

2”

47”

297⁄

8”

253⁄

8”

45”

36”

SINGLE OVEN DOUBLE OVEN

NOTE C

Both

Sides

NOTE: Use a 4′power cord to prevent interference

with the storage drawer. Power cords 41⁄2to 6′long

may have to be dressed to allow for proper drawer

closing.

MINIMUM DIMENSIONS BETWEEN COOKTOP,

WALLS AND ABOVE THE COOKTOP:

A. Make sure the wall covering, countertop, flooring

and cabinets around the range can withstand

the heat (up to 200°F) generated by the range.

B. Allow 30” minimum clearance between surface

units and bottom of unprotected wood or metal

cabinet, or allow a 24” minimum when bottom of

wood or metal cabinet is protected by no less

than 1/4” thick flame retardant millboard covered

with not less than No 28 MSG sheet metal,

(.015”), .015” thick stainless steel, .024”

aluminum or .020” copper.

Acceptable electrical outlet area.

Orient electrical receptacle so the

length is parallel to floor.

*GE-branded models have control

panels 30-

7⁄8” wide.

30”

⁄8

”

30”

C. This appliance has been approved for 0” spacing to adjacent surfaces above the cooktop.

However, a 6” minimum spacing to surfaces less than 15” above the cooktop and adjacent

cabinet is recommended to reduce exposure to steam, grease splatter and heat.

To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage

space above the cooktop should be avoided. If cabinet storage space is to be provided above the

cooktop, the risk can be reduced by installing a range hood that projects at least 5” beyond the

front of the cabinets. Cabinets installed above the cooktop must be no deeper than 13”.

297⁄8”

4”

31-10677 08-08 JR

ELECTRICAL REQUIREMENTS

WARNING: This appliance must be properly grounded.

WARNING:

All new constructions, mobile homes, recreational vehicles and installations

where local codes do not allow grounding through neutral, require a 4-conductor UL-listed range cord.

WARNING: To prevent fire or shock, do not use an extension cord with this appliance.

WARNING: To prevent shock, remove house fuse or open circuit breaker before

beginning installation.

We recommend you have the electrical wiring and hookup of your range connected by a qualified

electrician. After installation, have the electrician show you how to disconnect power from the

range.

You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you

connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring

must be used.

Effective January 1, 1996, the National Electrical Code requires that new construction (not

existing) utilize a 4-conductor connection to an electric range. When installing an electric range

in new construction, mobile home, recreational vehicle, or an area where local codes prohibit

grounding through the neutral conductor, refer to the section on four-conductor branch circuit

connections.

Check with your local utilities for electrical codes which apply in your area. Failure to wire your

oven according to governing codes could result in a hazardous condition. If there are no local

codes, your oven must be wired and fused to meet the National Electrical Code, NFPA No.

70 – latest edition, available from the National Fire Protection Association.

This appliance must be supplied with the proper voltage and frequency, and connected to an

individual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker

or time-delay fuse.

Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with

ring terminals on wire and a strain relief device.

A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range

cord is not recommended but if used, it should be marked for use with nominal 1

3⁄8″diameter

connection openings. Care should be taken to center the cable and strain relief within the

knockout hole to keep the edge from damaging the cable.

The rating plate is located on the oven frame or on the side of the drawer frame.

Rating plate

SINGLE OVEN

Rating plate

DOUBLE OVEN

POWER CORD AND CONDUIT INSTALLATION

Remove wire cover (on the back of range) by removing screws using a 1/4” nut driver.

Do not discard these screws.

For power cord and 1” conduit only,

remove

the knockout ring (13⁄8″) located on bracket

directly below the terminal block. To remove

the knockout, use a pair of pliers to bend the

knockout ring away from the bracket and

twist until ring is removed.

For 3/4” conduit installations only, purchase a squeeze connector matching the diameter

of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector

and tighten. Allow enough slack to easily attach the wires to the terminal block.

NOTE: Do not install the conduit without a squeeze connector. The squeeze connector MUST

be installed before reinstalling the rear range wiring cover.

Wire cover

5 screws to

remove

wire cover

Knockout

ring in

bracket

Knockout ring

removed

Retaining

tabs

Back of range

Terminal block

(appearance

may vary)

Terminal block cover

Screw to

remove

terminal

block cover

Back of range

SINGLE OVEN DOUBLE OVEN

For power cord installations only

(see the next step if using conduit),

assemble the strain relief in the hole.

Insert the power cord through the strain

relief and tighten. Allow enough slack

to easily attach the cord terminals to

the terminal block. If tabs are present at

the end of the winged strain relief, they

can be removed for better fit.

NOTE: Do not install the power cord

without a strain relief. The strain relief

bracket MUST be installed before

reinstalling the rear range wiring

cover.

Power cord

Strain relief

Terminal

block

Bracket

Squeeze

connector Terminal block

Conduit Bracket

PROCEED TO STEP 5 OR 6.

Wire tips

Terminal

block

Conduit

3-WIRE INSTALLATION

WARNING: The neutral or ground wire of the power cord must be connected

to the neutral terminal located in the center of the terminal block and the ground strap

must connect the neutral terminal to the ground plate. The power leads must be

connected to the lower left and the lower right terminals of the terminal block.

DO NOT remove the ground strap connection.

FOR POWER CORD INSTALLATION

A. Remove the 3 lower terminal screws from the terminal block.

B. Insert the 3 screws through each power cord terminal terminal ring and into the lower

terminals of the terminal block. Be certain that the center wire (white/neutral)

is connected to the center lower position of the terminal block.

C. Tighten screws securely into the terminal block.

FOR CONDUIT INSTALLATION

A. Loosen the 3 lower terminal screws on the terminal block. Strip wire to exposed tip about 5/8”

long.

B. Insert the center (white/neutral) wire tip through the bottom center terminal block opening.

On certain models, the wire will need to be inserted through the ground strap opening

and then into the bottom center block opening. Insert the two side bare wire tips into the lower

left and the lower right terminal block openings.

C. Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs.). Do not over-tighten

the screws.

NOTE: ALUMINUM WIRING: Aluminum building wire may be used but it must be rated

for the correct amperage and voltage.

PROCEED TO STEP 7.

Ground strap

Terminal block

(appearance

may vary)

Neutral terminal

Power cord

Ground

plate

Power Cord Conduit

4-WIRE INSTALLATION

WARNING: The neutral wire of the supply circuit must be connected to the neutral terminal

located in the lower center of the terminal block. The power leads must be connected to the lower left

and the lower right terminals of the terminal block. The grounding lead must be connected to the frame

of the range with the ground plate and the green ground screw.

FOR POWER CORD INSTALLATION

A. Remove the 3 lower terminal screws from the terminal block. Remove the ground screw and

ground plate and retain them. Cut and discard the ground strap. DO NOTDISCARD ANY SCREWS.

B. Insert the one ground screw into the power cord ground wire terminal ring, through the ground plate

and into the frame of the range.

C. Insert the 3 terminal screws (removed earlier) through each power cord terminal ring and into the lower

terminals of the terminal block. Be certain that the center wire (white/neutral) is connected to the center

lower position of the terminal block. Tighten screws securely into the terminal block.

FOR CONDUIT INSTALLATION

A. Loosen the 3 lower terminal screws on the terminal block. Remove the ground screw and ground plate

and retain them. Cut and discard the ground strap. DO NOT DISCARD ANY SCREWS. Strip wire

to exposed tip about 5/8” long.

B. Insert the ground bare wire tip between the range frame and the ground plate (removed earlier)

and secure it in place with the ground screw (removed earlier). Insert the bare wire (white/neutral) tip

through the bottom center of the terminal block opening. Insert the two side bare wire tips into the lower

left and the lower right terminal block openings.

C. Tighten the screws until the wire is firmly secured (35 to 50 inch-lbs.). Do not over-tighten the screws.

NOTE: ALUMINUM WIRING: Aluminum building wire may be used but it must be rated

for the correct amperage and voltage.

Before–Power Cord and Conduit

Terminal

block

Terminal

block

Neutral

terminal

Neutral

terminal

Ground

strap

Ground plate

(grounding to

range)

Ground

screw

Ground strap

After–Conduit

Terminal

block

Ground

plate

(grounding

to range)

Wire

tips

Ground screw

After–Power Cord

Produktspecifikationer

Varumärke:	GE
Kategori:	Ugn
Modell:	JB620DRBB
Färg på produkten:	Zilver
Vikt:	88 g
Bredd:	47 mm
Djup:	67 mm
Höjd:	31 mm
Förpackningens vikt:	108 g
Förpackningens bredd:	130 mm
Djuppackning:	230 mm
Förpackningshöjd:	85 mm
Användarmanual:	Ja
Certifiering:	REACH, CE, RoHS, TAA
Material:	Staal
Antal per paket:	1 stuk(s)
Bästa användningen:	Notebook
Harmoniserad systemkod (HS):	83014090