GE JX2030SMSS Bruksanvisning

GE Magnetron JX2030SMSS

Läs nedan 📖 manual på svenska för GE JX2030SMSS (8 sidor) i kategorin Magnetron. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/8

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Installation Built-In Trim Kits

Instructions JX2027 and JX2030

Read these instructions completely and carefully.

•IMPORTANT – Save these instructions for local inspector’s use.

•IMPORTANT – Observe all governing codes and ordinances.

•Note to Installer – Be sure to leave these instructions with the

Consumer.

•Note to Consumer – Keep these instructions for future reference.

•For easier installation and personal safety, we recommend that two people

install this microwave oven.

WARNING —This oven must be plugged into a properly

grounded 3-hole, 120V receptacle as required by the National Electrical Code

or the Canadian Electrical Code.

❒

BEFORE YOU BEGIN

• Do not alter or modify any part of this kit or the oven.

• Unplug the microwave oven before attempting installation of this kit.

• Skill level – Installation of this appliance requires basic mechanical and

electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not covered under the Warranty.

• This kit is UL/CSA listed for installation alone or over any GE/GE Profile

single electric wall oven. Not for use adjacent to (within 2 feet of) any gas

or electric range, cooktop or oven.

• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,

PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,

JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,

PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.

TOOLS YOU WILL NEED

❒ Phillips screwdriver

❒ Pencil

❒ Tape measure

❒ Awl or punch

❒ Drill with 7⁄64″bit or #35

FOR YOUR SAFETY:

WARNING – Before beginning the

installation, switch power off at service panel and lock

the service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the

service panel.

❒ Level

❒ Scissors (optional)

PART QUANTITY

❒ Trim Frame 1

❒ Bottom Duct 1

❒ Side Duct 1

❒ 4 mm x 12 mm 23

Round-Head Screws (21 required

for installation)

❒ 4 mm x 14 mm 6

Flat-Head Screws

(4 required for

installation)

❒ Anti-Tip Brace 1

❒ Anti-Tip Bracket 1

❒ Upper Duct 1

❒ Top Bracket 1

❒ Bottom Bracket 1

❒ Templates 2

PARTS INCLUDED

NOTE: This kit has extra screws to prevent the technician from spending extra

time locating a replacement screw in case they lose one during installation.

Questions? In the U.S., call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com.

In Canada, call 1.800.561.3344 or Visit our Website at: GEAppliances.ca.

❒

CUTOUT DIMENSIONS

* Min. depth with receptacle outside cabinet 191⁄2″

Min. depth with receptacle inside cabinet 22″

120 volt-60 Hertz grounded power receptacle

Installation Instructions

Models 27″30″

Height 163⁄4″163⁄4″

Width 251⁄2″251⁄2″

Depth (min.)* 191⁄2″or 22″191⁄2″or 22″

WARNING — This trim kit uses air flow

from the top, bottom and sides of the trim frame.

Blocking the air flow can cause the microwave to

function improperly and may cause damage to

the microwave.

Allow a 1 clearance beyond the edge of the trim″

frame to provide proper air flow.

On 27″models, allow 11⁄8″at the top, 11⁄16″on the sides

and 11⁄4″at the bottom for overlap of the Trim Frame

over the edges of the cutout.

On 30″models, allow 11⁄8″at the top, 21⁄16″on the sides

and 11⁄4″at the bottom for overlap of the Trim Frame

over the edges of the cutout.

FOR INSTALLATION ABOVE A

BUILT-IN OVEN:

Microwave oven should be installed on a 3/8″plywood

base and supported by 2x4 or 1x2 equivalent runners

on all sides. Base must be capable of supporting a

minimum of 100 lbs (45.3 kg).

Draw a line on the cutout floor at the center of the

cutout, and extend the line 1/2 down the face of″

the cabinet.

Draw a line on the top front face of the cabinet

at the center of the cutout. The line should extend

1/2″up the face of the cabinet. This center line will

be used for mounting the top bracket (see step 7).

Fold or cut the front edge of the template, along the

front guide line. Place the template flush along the

front edge of the cutout floor, aligning the center line

of the template with the center line of the cutout

floor. Mark the center positions with an awl or center

punch for the anti-tip brace location as shown.

Drill two holes for the anti-tip brace.

Install the anti-tip brace onto the cutout floor using

two round-head screws.

Round-head

screws (2)

Anti-Tip Brace

❒

INSTALL THE ANTI-TIP BRACE

Depth

Height

11⁄4″Overlap

Width

11⁄8″Overlap

1″Clearance

beyond trim frame

(on all sides)

3″Min.

27″Models: 11⁄16″overlap

30″Models: 21

⁄16″overlap

DIMENSIONS:

A = 11⁄2″

B = 3″

C = 183⁄16″

D = 1/2″

Bottom of trim kit

must be minimum

of 36″from floor

1′= 0.3 m

1″= 2.5 cm

Disconnect the microwave oven before proceeding with the

installation.

Fasten the anti-tip bracket to the bottom duct by using four

round-head screws.

Remove any loose items

inside the microwave oven,

including the turntable

and turntable support.

Carefully turn the

microwave upside down.

Install bottom duct with

four round-head screws

as shown.

Front

Rear

Round-Head Screws (4)

Installation Instructions

Set the microwave upright, being careful not to bend the front

flange. Remove the one existing screw from the left side of the

microwave oven.

As indicated on the supplied template (publication

#31-41003-1), fold or cut along the “cut lines” and place the

template on top of the microwave oven. By aligning the

template with the outside edges of the oven, you will see

exactly where to place the upper duct assembly. Peel off the

backing from the double-sided tape. Carefully position the

side duct and upper duct assembly on the microwave

cabinet, aligning with the bottom screw hole. Press down

firmly on the ducts. Fasten the duct assembly to the left

side of the cabinet with the screw removed above.

Existing Screw (1)

Round-Head Screws

Microwave Oven Upside Down

❒

INSTALL ANTI-TIP BRACKET AND

BOTTOM DUCT

❒

INSTALL SIDE DUCT AND UPPER

DUCT (cont.)

Anti-Tip Assembly

Bottom Duct

Round-Head

Screw

Anti-Tip Bracket

Anti-Tip

Brace

❒

INSTALL MICROWAVE OVEN

INTO CABINET

Connect the side duct to the upper duct as shown.

1. Insert projecting tabs of the upper duct into the holes

of the side duct.

2. Bend the tabs up with caution as shown.

NOTE: Remove any oil or dirt on the surface of the microwave

oven before the ducts are attached.

(2)

(1)

Upper Duct

Side Duct

3 Tabs

3 Holes

❒

INSTALL SIDE DUCT AND UPPER

DUCT

Slide the microwave oven part way into the cabinet opening.

Plug in the microwave oven.

The anti-tip bracket must be flat to the cutout floor to engage

correctly with the anti-tip brace as shown. Carefully slide the

microwave back, making sure the power cord is not mashed

or cut.

Center the microwave oven within the cutout opening and

slide the microwave oven in place, engaging the anti-tip brace.

Ensure the microwave oven is accurately centered

Produktspecifikationer

Varumärke:	GE
Kategori:	Magnetron
Modell:	JX2030SMSS

Behöver du hjälp?

Om du behöver hjälp med GE JX2030SMSS ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Magnetron GE Manualer

GE GCST07N1WWW Bruksanvisning

7 Januari 2025

GE GCHK07N1WBB Bruksanvisning

7 Januari 2025

GE GCHK07N1WWW Bruksanvisning

7 Januari 2025

GE GCST07N1WBB Bruksanvisning

7 Januari 2025

GE GCHK07N1WSS Bruksanvisning

7 Januari 2025

GE Profile PWB7030SVSS Bruksanvisning

7 Januari 2025

GE UVM9125STSS Bruksanvisning

31 December 2025

GE PVM9215DFWW Bruksanvisning

30 December 2025

GE Profile PVM9195DFCC Bruksanvisning

30 December 2025

GE JVM6175SFSS Bruksanvisning

30 December 2025

Magnetron Manualer

Nyaste Magnetron Manualer

Siemens BF634RGS1 Bruksanvisning

16 Januari 2025

Samsung C139STB Bruksanvisning

15 Januari 2025

Samsung C106F Bruksanvisning

15 Januari 2025

Samsung c137 Bruksanvisning

15 Januari 2025

Samsung C 137 NM X Bruksanvisning

15 Januari 2025

Samsung C138STB Bruksanvisning

15 Januari 2025

Samsung C100BM Bruksanvisning

15 Januari 2025

Samsung C100FM Bruksanvisning

15 Januari 2025

Etna a 2193 inox Bruksanvisning

15 Januari 2025

Samsung CE107FTP Bruksanvisning

15 Januari 2025