GE Profile JS966KDCC Bruksanvisning

GE Ugn Profile JS966KDCC

Läs nedan 📖 manual på svenska för GE Profile JS966KDCC (12 sidor) i kategorin Ugn. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/12
Skill Level: Average High Low
Completion Time: 1 to 3 Hours
Proper installation is the responsibility of the installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty. See the Owners Manual for warranty
information.
CAUTION: Before you begin
Read these instructions carefully and
completely.
• IMPORTANT- Save these instructions for
local inspector’s use.
• IMPORTANT- Observe all governing codes
and ordinances.
Self Cleaning Radiant
Electric Slide-In Range
Installation
Instructions JSP46, JSP56, JS966
• NOTE TO INSTALLER- Be sure to leave
these instructions with the consumer.
• OWNER- Keep these instructions for future
reference.
• WARNING- This appliance must be
properly grounded. See “Electrical
Requirements” page 2.
Parts Included
Tools You Will Need
Pub. No. 31-10426
229C4053P412 1
“If you have questions, Call 800-GE-CARES or visit our website at:
www.GEAppliances.com”
1/4”Nut
driver
Wrench or Pliers
(for 1 7/16” nut)
Pencil
Hand or
Saber Saw
Straight Edge
or Square
Materials Needed
Lag Bolts Anchor
Sleeves 4- Wire Cord
4’long
3 -Wire Cord
4’long
(For Concrete Floors
Only)
( UL Approved 50 AMP)
OR
1
2
3
4
Drill with
1/8” Bit
Anti-Tip Bracket
Screws
Safety
Glasses
Tape Measure Pliers
Level
Rear Filler
2 Screws
All rough-in and spacing dimensions must be met
for safe use of your range. Electricity to the range
can be disconnected at the outlet without moving
the range if the outlet is in the preferred location
(remove lower drawer).
To reduce the risk of burns or fire when reaching
over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet
storage space is to be provided above the
cooktop, the risk can be reduced by installing a
range hood that sticks out at least 5” beyond the
front of the cabinets. Cabinets installed above a
cooktop must be no deeper than 13”.
Be sure your appliance is properly installed and
grounded by a qualified technician.
WARNING: For personal safety
remove house fuse or open circuit
breaker before beginning
installation. Failure to do so could result in
serious injury or even death.
For Your Safety
2
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of
tipping, the appliance must be
secured by properly installing the
anti-tip bracket packed with the appliance.
If you pull the range out and away from the wall
for any reason, make sure the Anti-Tip bracket
is engaged when the range is pushed back
against the wall.
This appliance must be supplied with the proper
voltage and frequency, and connected to an
individual properly grounded branch circuit,
protected by a circuit breaker or fuse having
amperage as specified on the rating plate. The
rating plate is located above the storage drawer
on the oven frame.
We recommend you have the electrical wiring
and hookup of your range connected by a
qualified electrician. After installation, have the
electrician show you where your main range
disconnect is located.
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your
oven according to governing codes could result in
a hazardous condition. If there are no local
codes, your range must be wired and fused to
meet the requirements of the National Electrical
Code, ANSI/NFPA No. 70-Latest Edition. You can
get a copy by writing:
National Fire Protection Association
Battery March Park
Quincy, MA 02269
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing,
construction utilize a 4 conductor connection to
an electric range. When installing an electric
range in new construction, follow the instructions
in the section on NEW CONSTRUCTION AND
FOUR CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz electrical
system. If you connect to aluminum wiring,
properly installed connectors approved for use
with aluminum wiring must be used.
Electrical Requirements
WARNING
• All ranges can tip
• Injury to persons could result
• Install anti-tip bracket
packed with range
• See Installation Instructions
3
Installation Instructions
Pre- Installation Checklist
Inspect Installation Location
Refer to alternate construction section for
the following non standard installations.
a. Counter opening extends to the wall:
Maintop Filler (supplied with the range.)
(See Page 12 section AA for Installation
Instructions) or
Backguard (Kit JXS36XX or JXS39SS).
See page 12.
b. Counter height greater than 36 3/4”:
Lower Trim Slide-In (Kit JXS56XX).
c. One side is not enclosed by a cabinet:
Bodyside (Kit JXS76XX).
d. Island Installation:
To provide an optimum installation, the
top surface of the counter top must be
level and flat (lie on the same plane)
around the 3 sides that are adjacent to
range cooktop. Proper adjustments to
make the top flat should be made or
gaps between the countertop and range
cook top may occur. Forcing the cook
top to fit may cause excessive gaps and
could break glass and void warranty.
Inspect cutout dimensions and location
of receptacle to be sure it fits within
layout location.(See page 5.)
Do not remove the protective channel
from the sides of the glass cooktop, if
applicable, until later in installation.
Move Range Indoors In front
of Cabinet Opening
(Do not use hand trucks when moving the
unpackaged range.)
Protect the kitchen floor! Flatten and
place a piece of the shipping carton in front
of the installation location to protect the
flooring.
Carefully, tilt the range to access the range
leveling legs. Use an adjustable wrench to
screw leveling legs out so that glass
support flanges clear top of counter top.
To Procure Kits:
a. Visit GE Web Site, see page 1.
b. Call GE Answer Center, see page 1.
c. Contact Dealer
Protective Channel
Adjust

Produktspecifikationer

Varumärke: GE
Kategori: Ugn
Modell: Profile JS966KDCC

Behöver du hjälp?

Om du behöver hjälp med GE Profile JS966KDCC ställ en fråga nedan och andra användare kommer att svara dig


Ugn GE Manualer

GE

GE JBS08PICWW Bruksanvisning

18 Oktober 2024
GE

GE Profile JP939CHCC Bruksanvisning

17 Oktober 2024
GE

GE JSP26BDWH Bruksanvisning

17 Oktober 2024
GE

GE Profile JBP99SHSS Bruksanvisning

17 Oktober 2024
GE

GE JB710WHWW Bruksanvisning

15 Oktober 2024
GE

GE Adora JBP73HLBB Bruksanvisning

14 Oktober 2024
GE

GE JB700SNSS Bruksanvisning

14 Oktober 2024
GE

GE JGP330SEKSS Bruksanvisning

14 Oktober 2024
GE

GE Profile Performance JS960TBWW Bruksanvisning

11 Oktober 2024
GE

GE JBP62BMWH Bruksanvisning

9 Oktober 2024

Ugn Manualer

Nyaste Ugn Manualer

Taurus

Taurus HM778WHD Bruksanvisning

27 Oktober 2024
Lacanche

Lacanche CITEAUX Bruksanvisning

27 Oktober 2024
JennAir

JennAir JDS1450FS Bruksanvisning

27 Oktober 2024
Orima

Orima ORP-76-IN Bruksanvisning

27 Oktober 2024
Breville

Breville the Handy Hot Plate BHP150 Bruksanvisning

27 Oktober 2024
JennAir

JennAir JGRP436HL Bruksanvisning

27 Oktober 2024
Neff

Neff C17MS22G1 Bruksanvisning

27 Oktober 2024
Pit Boss

Pit Boss BK24 Bruksanvisning

27 Oktober 2024
Guzzanti

Guzzanti GZ-8206 Bruksanvisning

27 Oktober 2024
Avanti

Avanti DE2402SC Bruksanvisning

27 Oktober 2024