GE ZDIC150WBB Bruksanvisning

GE Ismaskin ZDIC150WBB

Läs nedan 📖 manual på svenska för GE ZDIC150WBB (18 sidor) i kategorin Ismaskin. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/18
Installation
Instructions
Automatic Ice maker
ZDIC150
ZDIS150
Design Guide
With Installation Instructions
monogram.com
Installation Instructions
• BEFORE YOU BEGIN:
Read these instructions completely and carefully.
• IMPORTANT:
Save these instructions for local inspector’s use.
• IMPORTANT:
Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded.
Failure to do so can result in death, fire or electrical
shock. See “Power Supply,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Le non-respect de ces instructions peut causer la
mort, un incendie ou un choc électrique. Consulter «
Alimentation électrique », page 6.
If you received a damaged ice maker, you should
immediately contact your dealer or builder.
Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
• Use this appliance only for its intended purpose.
Check with local utilities for electrical codes that
apply in your area. Local codes vary. Installation,
electrical connections and grounding must comply
with applicable codes. In the absence of local codes,
the ice maker should be installed in accordance
with National Electrical Code ANSI/NFPA 70-1990 or
latest edition.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram Service in Canada, call
1.800.561.3344.
For Monogram Parts and Accessories, call
1.800.626.2002.
2
CONTENTS
Design Information
Models Available .................................................................... 3
Optional Accessories ........................................................... 3
Tools and Materials Required ........................................ 3
Cutout & Product Dimensions .........................................4
Installation
Advance Planning .................................................................4
Water Supply ........................................................................... 5
Power Supply ........................................................................... 6
Remove Packaging ............................................................... 6
Water Filtration System ................................................. 6, 7
Adjust Height of Ice maker ...............................................7
Connect the Drain ................................................................. 9
Connect Water Supply to Appliance ............................9
Reverse Door Swing ...................................................10, 11
Accessories
ZPK2 Auxiliary Pump Kit ............................................ 12-15
ZIP75BB Kit for 3/4” thick panels ..........................16, 17
Design Information
MODELS AVAILABLE
ZDIC150ZBB, ZDIS150ZSS
Available in black and stainless steel.
The ice maker may be installed below a countertop
or used free-standing.
3
OPTIONAL ACCESSORIES
=,3%%³For the installation of a trimless
3/4” thick custom panel on black models (not for
stainless steel models). This kit provides a handle
that can be installed with the custom panel.
A custom handle of your choice may be installed onto
the 3/4” panel. See installation instructions
on pages 10 and 11.
ZPK2 Drain Pump Kit - For use when a floor drain is
not available. The drain pump must be installed
inside the unit and can pump discharge water at a
maximum vertical height of 10 feet. 10 feet of tubing
is supplied with the kit.
TOOLS AND MATERIALS REQUIRED FOR BASIC INSTALLATION
• 1/4” socket
• 3/4” adjustable wrench
• Level
• GE SmartConnect™ Refrigerator Tubing Kit or 1/4” O.D.
copper tubing, of sufficient length to reach the installation
• Flat-blade screwdriver
• 7/16” and 1/2” open-end wrenches or 2 adjustable wrenches
• 1/4” nut driver

Produktspecifikationer

Varumärke: GE
Kategori: Ismaskin
Modell: ZDIC150WBB

Behöver du hjälp?

Om du behöver hjälp med GE ZDIC150WBB ställ en fråga nedan och andra användare kommer att svara dig


Ismaskin GE Manualer

GE

GE Profile Opal P4AAKASSWOW Bruksanvisning

24 September 2024
GE

GE Profile Opal P4AAKASSWBB Bruksanvisning

24 September 2024
GE

GE Profile Opal P4AAKASSWSS Bruksanvisning

24 September 2024
GE

GE Profile Opal XPIO23SWSS Bruksanvisning

24 September 2024
GE

GE Profile PIP70SS Bruksanvisning

16 September 2024
GE

GE ZDI15CBB Bruksanvisning

2 September 2024
GE

GE ZDIC150WWW Bruksanvisning

26 Augusti 2024
GE

GE Profile Opal OPAL01NSS Bruksanvisning

25 Augusti 2024
GE

GE Profile OPAL01PSS Bruksanvisning

23 Augusti 2024
GE

GE ZDIS15CSS Bruksanvisning

22 Augusti 2024

Ismaskin Manualer

Nyaste Ismaskin Manualer

Domo

Domo DO2309L Bruksanvisning

8 Januari 2025
Spaceman

Spaceman 6250 Bruksanvisning

8 Januari 2025
Eldom

Eldom Cube KS200 Bruksanvisning

7 Januari 2025
Eldom

Eldom Cristall KS210 Bruksanvisning

7 Januari 2025
Cuisinart

Cuisinart ICE31U Bruksanvisning

7 Januari 2025
Haier

Haier HI50IB20SS Bruksanvisning

3 Januari 2025
Royal Catering

Royal Catering RCHI-01 Bruksanvisning

1 Januari 2025
Jocel

Jocel JMFG001764 Bruksanvisning

31 December 2025
Waring Commercial

Waring Commercial WCIC25 Bruksanvisning

30 December 2025
Scotsman

Scotsman B330P Bruksanvisning

27 December 2024