Hanwha TNU-6320 Bruksanvisning

Läs nedan 📖 manual på svenska för Hanwha TNU-6320 (67 sidor) i kategorin övervakningskamera. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/67
NETWORK CAMERA
User Manual
TNU-6320
Copyright
©2018 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be
provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Hanwha Techwin reserves the
right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.
The initial administrator ID is admin and the password should be set when logging in for the first time.
Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a users responsibility for the security and any other problems caused by mismanaging a password.
Network Camera
User Manual
English _3
OvERviEW
iMpORTANT SAfETy iNSTRuCTiONS
1. Before installation, read all manuals thoroughly and proceed with the installation according to
the directions.
2. When connecting a power cable or signal line, check the external connection port first.
Incorrectly connecting the power supply may cause fire, electric shock or damage to the
product.
3. If you notice any unusual smells or smoke coming from the unit, stop using the product.
If this occurs, immediately disconnect the power source and contact the service center.
Continued use may cause fire or electrical shock.
4. Do not disassemble while the power is on.
5. Before the power is supplied, confirm that all power cords have been properly connected.
An insecure connection may result in fire.
6. If the system has been in a high or low temperature environment, you may be injured by high
heat or low chill of the surface.
7. Before turning the power on, confirm that the power supply supports 24Vac/6A 50/60Hz.
Power in excess of the rated voltage may cause a fire.
8. Lightning or thunder may cause damage to the device.
When installing the product, consider taking measures that will minimize damage to the
product in the event of lightning.
9. When the system is installed, it should be tightly anchored on a floor that can sufficiently
sustain its weight against any strong wind.
The fixing method and material used must be able to sustain at least 4 times the systems
weight.
10. Since the system is remotely controlled and sometimes changes its position, it should be so
carefully installed that it does not create any harmful environment, i.e., its moving part does
not injure people.
11. Do not attach anything to the system.
12. When installing in a dangerous environment, remove the equipment from the power supply
to reduce the possibility of ignition.
13. Do not install near a heater or motor.
Install the system in a place with good ventilation.
14. You can receive installation support from engineers who are qualified to handle technical
services.
15. Do not install the product in a location that is humid, or where the product will be exposed
to dust or soot.
16. Do not drop objects on the product, or apply strong impact to it.
Keep away from locations where there is excessive vibration or magnetic interference.
17. Do not install in an operating environment with extreme temperatures.
The camera will operate at temperatures of -40°C or higher.
18. Keep out of direct sunlight, and away from heat radiation sources.
19. If you want to relocate a product that has already been installed, be sure to turn off the
power and then move or reinstall it.
Failure to turn off the power may result in fire or electric shock.
20. Install the product in a location with good ventilation.
When connecting a power cable or signal line, check the external connection port first.
21. The rubber part of the camera wiper is expendable. Replace with a new one if performance
is degraded.
22. Before cleaning the system, disconnect it from the power supply.
CAuTiON
CAuTiON
RiSK Of ELECTRiC SHOCK.
DO NOT OpEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
overview

Produktspecifikationer

Varumärke: Hanwha
Kategori: övervakningskamera
Modell: TNU-6320

Behöver du hjälp?

Om du behöver hjälp med Hanwha TNU-6320 ställ en fråga nedan och andra användare kommer att svara dig




övervakningskamera Hanwha Manualer

övervakningskamera Manualer

Nyaste övervakningskamera Manualer