Harley Davidson J02994 (2003) Bruksanvisning
Harley Davidson
Motor
J02994 (2003)
Läs nedan 📖 manual på svenska för Harley Davidson J02994 (2003) (2 sidor) i kategorin Motor. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
INSTRUCTIONS
-J02994 REV. 10-10-2003
SHIFTER LINKAGE COVER
General
This “Harley-Davidson script”-style shifter-linkage cover kit
fits 1997 and later FXDWG (Dyna Wide Glide®) model motor-
cycles. This kit also fits 1993 and later Dyna models
equipped with Forward Control Kit 49080-03.
NOTE
A Service Manual for your model motorcycle is available
from any Harley-Davidson dealer.
Installation
1. See the Service Parts illustration. Obtain an upper mount-
ing bracket (2), lower mounting bracket (3), two 1/2-inch
long screws and the Allen wrench (6) from the kit.
2. See Figure 1. Assemble the upper and lower mounting
brackets onto the shaft of the ball screw shell at one
end of between the ball screw (3) andthe shifter rod (1),
the jam nut (2) so the shaft passes above the three
holes in the brackets.
Insert the two screws in the outboard holes of the lower
bracket, and use the Allen wrench to thread them part
way into the holes in the upper bracket. Do not fully
tighten the screws at this time.
3. Repeat Steps 1 and 2 at the other end of the shifter rod.
4. Position the linkage cover (1) on top of the linkage and
examine the fit.
• If the cover fits properly, proceed to Step 8.
• If the center holes in the front and rear upper mounting
brackets cannot be adjusted to line up with the holes
on the inboard side of the cover, the linkage will need
to be adjusted to accept the cover. Proceed to Step 5.
5. See Figure 1 (below) and SHIFTER LINKAGE
ADJUSTMENT in the Service Manual. To adjust the
length of the linkage, remove the link attaching nut (5)
and flat washer at the forward ball screw.
6. Loosen the jam nut (2) at the front end of the shifter rod,
and remove the mounting bracket installed in Step 3.
Rotate the forward ball screw shell to achieve the prop-
er length to allow mounting of the cover.
7. Re-attach the ball screw to the shifter lever with the flat
washer and nut removed in Step 5. Torque the nut on
the ball stud to 70-90 in-lbs (7.9-10.2 Nm).
Torque the jam nut on the shifter rod to 20-24 ft-lbs
(27.1-32.5 Nm).
8. Fasten the rear of the cover (1) to the rear upper bracket
using a short screw (5) from the kit. Fasten the front of
the cover to the front bracket with the remaining screw.
Tighten the cover securely to the upper brackets.
Position the cover upright over the shifter rod, and tight-
en the four remaining screws to clamp the brackets
securely to the ball screw shells.
9. If the linkage needed adjustment (Steps 5 through 7),
the position of the shift foot lever (6) may have
changed.
To return the lever to the original position, loosen the
socket head screw (7) holding the lever to the shaft. Pull
the lever from the shaft, rotate to the desired angle and
slide the lever back onto the shaft.
Torque the screw to 18-22 ft-lbs (24.4-29.8 Nm).
®
Kit Number 33878-04
1 of 2
Figure 1. Stock Shifter Linkage
i02475
1. Shifter rod
2. Jam nut (2)
3. Ball screw shell (2)
4. Shifter lever
5. Link attaching nut
6. Shift foot lever
7. Socket screw
2
31
4
5
2
6
3
7
-J02994 2 of 2
Service Parts
®
Shifter Linkage Cover
Date 10/03
Part No. 33878-04
Item Description (Quantity) Part No.
1 Linkage cover Not sold separately
2 Mounting bracket (upper) (2) 33879-04
3 Mounting bracket (lower) (2) 33880-04
4 Screw, button head, hex socket,
#10-24 x 1/2 in (4) 94381-92T
5 Screw, button head, hex socket,
#10-24 x 1/4 in (2) 3339
6 Allen wrench, 1/8 in Not sold separately
i02476
1
5
2
3
4
5
2
3
4
6
Produktspecifikationer
| Varumärke: | Harley Davidson |
| Kategori: | Motor |
| Modell: | J02994 (2003) |
Behöver du hjälp?
Om du behöver hjälp med Harley Davidson J02994 (2003) ställ en fråga nedan och andra användare kommer att svara dig
Motor Harley Davidson Manualer
29 September 2024
22 September 2024
17 September 2024
27 Augusti 2024
25 Augusti 2024
24 Augusti 2024
23 Augusti 2024
21 Augusti 2024
20 Augusti 2024
20 Augusti 2024
Motor Manualer
- Motor Yamaha
- Motor Aprilia
- Motor Metabo
- Motor Juki
- Motor Milwaukee
- Motor Suzuki
- Motor BMW
- Motor Mitsubishi
- Motor Kettler
- Motor Husqvarna
- Motor Hyosung
- Motor Indian
- Motor Danfoss
- Motor Bajaj
- Motor Mash
- Motor Beta
- Motor Texas
- Motor Honda
- Motor KTM
- Motor Mercedes-Benz
- Motor Kawasaki
- Motor Hero
- Motor Ducati
- Motor Triumph
- Motor Benelli
- Motor Victory
- Motor Reebok
- Motor Emco
- Motor Cagiva
- Motor Moto Guzzi
- Motor Piaggio
- Motor Derbi
- Motor TVS
- Motor SMC
- Motor Ridley
- Motor GasGas
- Motor Sherco
- Motor Royal Enfield
- Motor Anova
- Motor Zero
- Motor Joy-it
- Motor MV Agusta
- Motor BodyCraft
- Motor Mahindra
- Motor CRRCpro
Nyaste Motor Manualer
1 Mars 2025
22 Februari 2025
18 Februari 2025
17 Februari 2025
16 Februari 2025
16 Februari 2025
15 Februari 2025
14 Februari 2025
8 Februari 2025
8 Februari 2025