Hikvision DS-2CE56D1T-AVPIR3(2.8-12MM) Bruksanvisning

Hikvision övervakningskamera DS-2CE56D1T-AVPIR3(2.8-12MM)

Läs nedan 📖 manual på svenska för Hikvision DS-2CE56D1T-AVPIR3(2.8-12MM) (4 sidor) i kategorin övervakningskamera. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
TURBO HD
1080P Dome Camera
User Manual
UD.6L0201D1939A01
1.2 Overview
1.2.1 Overview of Type I Dome Camera
1.2.2 Overview of Type Dome Camera
II
1 Introduction
1.1 Product Features
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l Support IR cut filter with auto switch;
l OSD menu, parameters are configurable;
l Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
l SMART IR mode;
l Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Ceiling Mounting
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2 Loosen the screws on the bubble of type 1
.
camera /rotate the bubble of type2 camera to
remove the bubble and the black liner.
Figure 2-2 Remove the Bubble
2 Installation
Before you start:
Figure 1-1 Overview of Type I Dome Camera
Figure 1-2 Overview of Type Dome CameraII
Type I: Type I :I
Black Liner
Bubble
Power Cable
HD Video Cable
Lens
Base plate
Back Box
Lens
Bubble
Black Liner
Power Cable
HD Video Cable
Type I :IType I:
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual applies to
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
0100001050409
Please refer to the product specification for
camera parameters and functions.
Type
Type
Type
I
II
Model
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
DS-2CE56D1T-AVPIR3/ VPIR3
DS-2CE56D1T-AVFIR/VFIR
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Screw the bolts through the mount by aligning
with the 2 bolt holes. Fit the toggles onto the bolts.
3.Push the two toggle bolts through the two screw
holes on the ceiling. Rotate the bolt till the toggle
holds the ceiling tightly.
2.2 In-ceiling Mounting
Figure 2-5 Install the Mount
Figure 2-6 Fix the Camera to the Mount
Figure 2-8 Fix the Camera to the Gang Box
6. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
4.Route and connect the corresponding cables.
5.Fix the camera to the in-ceiling mount with the
supplied screws.
3.Attach the back box of type 1 camera /base plate
of type2 camera to the ceiling and secure them
with supplied self-tapping screws.
4.Route the cables through the cable hole.
5.Align the camera with the back box/base plate,
and tighten the set screws to secure the camera
with the back box/base plate.
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure below
to get an optimum angle.
8. Fit the black liner on the camera and tighten the
screws on the bubble of type 1 camera or rotate the
bubble of type 2 camera to complete.
Figure 2-4 3-axis Adjustment
You need to purchase an in-ceiling mount separately
if you adopt in-celling mounting.
2.3 In-ceiling Mounting
in-ceiling mounting with gang box is supported by
the both types of camera.
1.Repeat steps 2-3 of the In-ceiling Mounting
section to secure the in-ceiling mount (supplied)
to the gang box.
Figure 2-7 Install the Mount
2.Route and connect the corresponding cables.
3.Align the camera with the gang box, and tighten
the screws to secure the camera with the gang box..
5. Repeat steps 6-8 of the Ceiling Mounting section
to complete the installation.
Type I: Type I :I
0 ~75° °
0 ~355° °
0 ~355° °
P
P
P
PP Direction
Direction
Direction
DirectionDirection
R
R
R
RR Direction
Direction
Direction
DirectionDirection
T
T
T
TT Direction
Direction
Direction
DirectionDirection
Type I:
0°~355°
0 ~75° °
0 ~340° °
T
T
T
TT Direction
Direction
Direction
DirectionDirection
R
R
R
RR Direction
Direction
Direction
DirectionDirection
P
P
P
PP Direction
Direction
Direction
DirectionDirection
Type I :I
Type I: Type I :IType I :IType I :I
3.2.2 W B
3.2.1 AE
Move the cursor to AE, and you can adjust the
image brightness by the ,BRIGHT NESS EXPOSURE
MODE AGC, and .
:Brightness
Brightness refers to the brightness of the image.
Exposure Mode:
Move the cursor to , you can selectExposure Mode
the exposure mode between and .Globe BLC
When BLC is selected as the exposure mode, the
level of BLC mode can be adjusted, as shown in the
Figure 3-2.
3.2.4 VIDEO SETTING
Contrast:
Contrast enhances the difference in color and light
between parts of an image.
You can set the value from 1 to .
10
Sharpness:
Sharpness determines the amount of
detail that an imaging system can reproduce.
You can set the value from 1 to 10.
Saturation:
You can set the saturation level of the image. The
value is from 0 to 10.
DNR:
DN R decreases the noise effect, especially in low
light conditions and delivers more accurate and
sharp image quality. You can set the value from
0 to 7.
:Mirror
You can set the Mirror status as H, V, H V, or OF F.
3 Menu Operation
Figure 3-1 Main Menu
VIDEO
SETTING
DAY/NIGHTWB RESET
BRIGHTNESS MODE
INFRARED
SMART IR
CONTRAST
SHARPNESS
SATURATION
EXITAE
DNR
MIRROR
EXPOSURE MODE
AGC
SAVE/EXIT
With a coaxial camera controller (purchase
separately) or calling the preset No.95 you can
select the menu and adjust the camera parameters.
3.1 FORMAT
You can set the format as PAL/NTSC.
3.2 SET UP
Move the cursor to , and press menu buttonSET U P
to enter the SET UP sub menu.
EXPOSURE
1.BRIGHTNESS
2.EXPOSURE MODE
LEVEL
3.AGC
4.RETURN
5
BLC
5
MIDDLE
Move the cursor to WB, and you can set White
Balance mode as and in this menuAWB MWB .
AWB: white balance is being adjusted
automatically.
: Set the value from 1 to 10.MWB R GAIN/B GAIN
As shown in Figure 3-3.
WB
MODE MWB
R GIAN 1-|--10
B GAIN 1-|--10
RETURN 8
AGC:
AGC optimizes the clarity of image in poor light
scene. AGC level can be set as OFF, LOW, MIDDLE
and HIGH.
Figure 3-2 EXP OSURE
Figure 3-3 WB
Figure 3-4 DAY/NIGHT
3.2.3 DAY & NIGHT
Move the cursor to DAY & NIGHT, and select
COLOR B/W SMART, , or as the DAY & NIGHT mode.
COLOR: The image is colored in day mode all the
time.
: The image is black & white all the time, andB/W
the IR LED turns on in the low-light conditions.
: Select to turn on/off the INFRARED_LAMPSMART
and to set the Smart IR level from 1to 16.
As shown in Figure 3-4.
DAY/NIGHT
MODE SMART
INFRARED OFF
SMART IR 0-|--5
RETURN 8
3.2.7 SAVE/EXIT
3.2.5 Reset
Reset all the settings to the default.
3.2.6 EXIT
Exit and Save & exit are selectable.
Move the cursor to , and press OK toSAVE & Exit
save the settings and exit the menu.

Produktspecifikationer

Varumärke: Hikvision
Kategori: övervakningskamera
Modell: DS-2CE56D1T-AVPIR3(2.8-12MM)

Behöver du hjälp?

Om du behöver hjälp med Hikvision DS-2CE56D1T-AVPIR3(2.8-12MM) ställ en fråga nedan och andra användare kommer att svara dig


övervakningskamera Hikvision Manualer

Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Bruksanvisning

8 Januari 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Bruksanvisning

8 Januari 2025
Hikvision

Hikvision THC-T127-PTLTS Bruksanvisning

7 Januari 2025
Hikvision

Hikvision DS-2CE16U0T-LF Bruksanvisning

19 December 2024
Hikvision

Hikvision DS-2CE10KF3T-LSYE Bruksanvisning

19 December 2024
Hikvision

Hikvision DS-2CE10KF3T-LS Bruksanvisning

19 December 2024
Hikvision

Hikvision DS-2CE76U0T-LMF Bruksanvisning

19 December 2024
Hikvision

Hikvision DS-2CE12KF3T-LSYE Bruksanvisning

19 December 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Philips

Philips B120E Bruksanvisning

16 Januari 2025
Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Bruksanvisning

10 Januari 2025
Speco Technologies

Speco Technologies O5LB1 Bruksanvisning

8 Januari 2025
ZKTeco

ZKTeco AntarVis 2.0 Bruksanvisning

8 Januari 2025
Speco Technologies

Speco Technologies O2P30X Bruksanvisning

8 Januari 2025
TP Link

TP Link InSight S345ZI Bruksanvisning

8 Januari 2025
Lorex

Lorex LNZ43P4A Bruksanvisning

8 Januari 2025
Lorex

Lorex C221NA Bruksanvisning

8 Januari 2025
Lorex

Lorex C221NC Bruksanvisning

8 Januari 2025
Kguard

Kguard QRT-501 Bruksanvisning

7 Januari 2025