Honeywell HBD95S Bruksanvisning

Honeywell övervakningskamera HBD95S

Läs nedan 📖 manual på svenska för Honeywell HBD95S (2 sidor) i kategorin övervakningskamera. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
Document 800-09587 – Rev A – 11/11
HBD9 Series Camera Quick Install Guide
800-09587 Rev A 11/11
Camera Overview
Installing the Camera
HBD9 Series cameras (HBD92S/HBD92SX/HBD95S/HBD95SX) can be installed on a
wall or ceiling indoors or outdoors.
Mounting the Camera
1. Find a suitable location for mounting the camera. The mounting surface must be
flat and capable of supporting the combined weight of the camera, sunshield,
bracket, and mounting ring (approximately 3.18 lb. [1.44 kg]).
2. Attach the mounting ring to the mounting surface using the four supplied 1-inch
(25.4 mm) self-drilling screws.
3. Attach the camera and bracket to the mounting ring using the four supplied
3/8-inch (9.52 mm) socket cap screws. Tighten the screws using the supplied hex
key.
Note For an outdoor wall mount installation, ensure that the notch in the base of the bracket is
facing down.
Positioning the Camera
You can position the camera to capture the desired field of view by adjusting the multi-
directional bracket. To change the camera position, loosen the bracket screws with
the supplied hex key, reposition the camera, and then tighten the screws.
Connecting the Camera
1. Connect the camera’s BNC video output to the video input on your monitor or
digital video recorder.
2. Connect the camera’s 12 V DC power output to a power supply appropriate for
your installation (24 V AC or 12 V DC).
Figure 1 Video and Power Connections
Note
When the main video is connected to a terminated monitor or recording device, if the
second video out is also connected to a terminated monitor, the video will become darker.
For correct video level, ensure that only
one
video output is terminated with a 75 ohm load.
Configuring the Camera
Setting the Focus and Zoom
The focus and zoom controls are located on the underside of the camera.
Figure 2 Focus and Zoom Controls*
To set the focus:
1. Loosen the focus set screw using the supplied hex key.
2. Turn the focus adjustment screw clockwise for near focus (N) or
counterclockwise for far focus (
∞).
3. Tighten the focus set screw to lock the focus setting.
To set the zoom:
1. Loosen the zoom set screw using the supplied hex key.
2. Turn the zoom adjustment screw clockwise to decrease zoom (W) or
counterclockwise to increase zoom (T).
3. Tighten the zoom set screw to lock the zoom setting.
Setting the LED Brightness
You can adjust the LED brightness level in night (B/W) mode. The LED brightness
control is located on the underside of the camera, next to the focus and zoom
controls. Unscrew the cap to access the control board.
Figure 3 Camera Control Board
To set the LED brightness:
Turn the LED LEVEL adjustment screw either clockwise to increase the LED
brightness or counterclockwise to decrease the LED brightness.
Programming the Camera
You can program the camera using the onscreen display (OSD) menus. The menu
controls are located on the camera control board (Figure 3). Move the OSD controller
joystick up, down, left, or right to navigate through the menu options. Press the
joystick to execute (set) a selection or to enter a submenu (
).
Figure 4 Setup Menu Structure
Sunshield
Mounting
Ring
Bracket
Notch
Video (BNC) - Yellow
Power (12 V DC) - Red
N
T W
Zoom Adjustment Screw
Focus Adjustment Screw
SETUP
LED LEVEL
VIDEO
TEST
OSD Controller
LED Adjustment Screw
2nd Video Out
<<SETUP MENU>>
LENS DC
EXPOSURE
WHITE BAL ATW
SSDR OFF
BACKLIGHT OFF
DNR3 ON
DAY/NIGHT EXTERN
SPECIAL
EXIT SAVE
1
2
3
4
5
6
7
8
9
LENS DC
EXPOSURE
WHITE BAL
SSDR
BACKLIGHT
SPECIAL
DAY/NIGHT
DNR3
BRIGHTNESS, SHUTTER, AGC,
SENS-UP, RETURN
ATW, OUTDOOR, INDOOR,
MANUAL, AWCSET
OFF, ON
OFF, BLC, HLC
ON, OFF
EXTERN, COLOR, B/W, AUTO
See Special Menu Structure.
Main Setup Menu Menu OptionsSubmenu
* The HBD92S(2.8–12 mm) controls are shown here.
The controls appear in reverse order on the HBD95S (5–50 mm).
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-09587 – Rev A – 11/11
© 2011 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in
all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this
publication may be issued to incorporate such changes.
Setup Menu
Special Menu Structure
On the Setup menu, select SPECIAL, and then press Set to open the Special menu.
Figure 5 Special Menu
Special Menu
Regulatory Compliance Notices
Information to the user: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential requirements of EMC directive 2004/108/EC, conforming to the requirements of
standards EN 55022 for emissions, EN 50130-4 for immunity, and EN 60950 for electrical
equipment safety.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
product returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service at
1.800.796.CCTV (North America only) for assistance or to request a Return Merchandise
Authorization (RMA) number. For Europe and the United Kingdom, please contact your
Honeywell dealer.
Be sure to have the model number, serial number, and the nature of the problem available for
the technical service representative. Prior authorization must be obtained for all returns,
exchanges, or credits. Items shipped to Honeywell without a clearly identified Return
Merchandise Authorization (RMA) number may be refused.
Menu Item Description
1LENS DC: Set BRIGHTNESS (1 to 70), IRIS SPEED (1 to 5), and FOCUS ADJUST
(mode and shutter range).
2EXPOSURE BRIGHTNESS: Set picture brightness (1 to 70).
SHUTTER: Set to ESC, MANUAL, A.FLK, or --- (FIXED). ESC controls
shutter speed automatically depending on ambient illumination of subject;
MANUAL controls shutter speed manually (NTSC = 1/60 to 1/120,000 s,
PAL = 1/50 to 1/120,000 s); A.FLK reduces picture flicker; --- fixes the
shutter speed (NTSC = 1/60 s, PAL = 1/50 s) to prevent color rolling.
AGC (Auto Gain Control): Set to OFF, LOW, or HIGH. Increasing gain
allows for a useable picture in lower light conidtions. The higher the gain
the lower the light levels. As gain is incresed, low light noise may also
increase.
SENS-UP: Set to OFF or AUTO (×2 to ×512). When activated, the camera
automatically detects the light level and maintains a clear picture. Note:
When SHUTTER is set to MANUAL or A.FLK mode, SENS-UP is disabled.
3WHITE BAL ATW (Auto Tracing White Balance): Select when the color temperature is
between 1700 K and 11,000 K.
OUTDOOR: Select when the color temperature is between 1700 K and
11,000 K (sodium light inclusion).
INDOOR: Select when color temperature is between 4500 K and 8500 K.
MANUAL: Select to fine-tune white balance (RGAIN, BGAIN levels
adjustable).
AWC
SET (Auto White Balance Control): To detect the optimal light level
for the current environment, point the camera towards a sheet of white
paper and then press Set.
4SSDR SSDR (Super Dynamic Range): Set to ON to even out the overall
brightness of high contrast images by lightening the darker areas of the
image.
5BACKLIGHT BLC: Set backlight LEVEL (LOW, MIDDLE, HIGH) and area to be
enhanced (TOP, BOTTOM, LEFT, RIGHT). Note: BLC does not work in the
B/W mode of the DAY/NIGHT menu.
HLC
: Set highlight compensation LEVEL (LOW, MIDDLE, HIGH), LIMIT (ALL
DAY, NIGHT ONLY), MASK COLOR (BLACK, RED, BLUE, CYAN,
MAGENTA), MASK TONE (1 to 25), and area to be masked (TOP, BOTTOM,
LEFT, RIGHT).
Note:
HLC is only activated when a bright light exceeds a
specific size.
6DNR3 DNR3 (Digital Noise Reduction): Set to ON and adjust level (1 to 32) to
reduce low-light background noise.
7DAY/NIGHT EXTERN: Select to use built-in light sensor to automatically switch
between day (color) and night (black and white) mode.
COLOR: Select to always display picture in color.
B/W: Select to always display picture in black and white.
AUTO: Select to display picture in color in a normal environment, and in
black and white in low light conditions (BURST MODE turns burst signal on
or off; DURATION and DWELL TIME set day/night switching point).
8SPECIAL Opens the SPECIAL menu (see Special Menu Structure).
9EXIT SAVE: Select to save the current settings and exit.
NOT SAVE: Select to exit without saving the current settings.
RESET: Select to reset the camera to the factory default settings.
Language, communication, and monitor settings are not initialized.
<<SPECIAL MENU>>
IMAGE ADJ
MONITOR LCD
CAM TITLE OFF
SYNC INT
MOTION DET OFF
PRIVACY OFF
COMM ADJ
LANGUAGE ENGLISH
RETURN
1
2
3
4
5
6
7
8
9
IMAGE ADJ V-REV, H-REV, D-ZOOM, DIS,
FONT COLOR, SHARPNESS
MONITOR
CAM TITLE
SYNC
MOTION DET
COMM ADJ
PRIVACY
LCD, USER, CRT
OFF, ON
INT, LL (not supported)
OFF, ON (SENSITIVITY, AREA
MODE, SEL POS, XPOS, YPOS,
FILLSET)
OFF, ON (AREA, MODE, MASK
COLOR, MASK TONE, TOP,
BOTTOM, LEFT, RIGHT)
CAM ID, BAUD RATE, UART
MODE, RET PKT, DISP ID,
PROTOCOL
Menu OptionsSubmenu
LANGUAGE
ENGLISH, OTHER LANGUAGES
(selection varies by model)
Menu Item Description
1IMAGE ADJ V-REV: Select to flip picture vertically. Note: Text does not flip.
H-REV: Select to flip picture horizontally.
D-ZOOM: Set digital zoom (×1 to ×16).
DIS: Set digital image stabilization to ON or OFF. Note: Using DIS lowers the
camera resolution.
FONT COLOR
: Set OSD color to blue, white, yellow, green, red.
SHARPNESS: Set picture sharpness (1 to 20).
2MONITOR LCD: Select if using an LCD monitor.
USER: Select if using a non-standard monitor.
CRT: Select if using a CRT monitor.
Adjust gamma, PED level (1 to 70), and color gain levels using the submenus.
3CAM TITLE Set to ON to display a camera title (up to 15 letters in length) on the monitor
screen. Note: This option is only available in English.
4SYNC INT: Synchronize the vertical interval sync pulse of your camera with other
equipment to reduce the effect of picture roll on the monitor.
5MOTION DET SENSITIVITY: Select motion detection areas (AREA1 to AREA8).
AREA MODE: Enable or disable selected motion detection area.
SEL POS: Select quadrant of motion detection area to use (L_TOP, R_TOP,
L_BOTTOM, R_BOTTOM).
XPOS: Set coordinate of horizontal axis for SEL POS.
YPOS: Set coordinate of vertical axis for SEL POS.
FILL
SET: Select to fill in selected motion detection area.
6PRIVACY AREA: Select privacy areas (AREA1 to AREA12).
MODE: Enable or disable selected privacy area.
MASK COLOR: Set color of privacy mask (GREEN, RED, BLUE, BLACK,
WHITE, GRAY).
MASK TONE: Adjust brightness of MASK COLOR.
TOP/BOTTOM/LEFT/RIGHT: Adjust size and position of selected privacy zone
areas.
7COMM ADJ This option is not currently supported.
Waste Electrical and Electronic Equipment (WEEE)
Correct disposal of this product (applicable in the European Union and other
European countries with separate collection systems): This product should
be disposed of, at the end of its useful life, as per applicable local laws,
regulations, and procedures.

Produktspecifikationer

Varumärke: Honeywell
Kategori: övervakningskamera
Modell: HBD95S

Behöver du hjälp?

Om du behöver hjälp med Honeywell HBD95S ställ en fråga nedan och andra användare kommer att svara dig


övervakningskamera Honeywell Manualer

Honeywell

Honeywell Performance H4W8PER2V Bruksanvisning

21 December 2024
Honeywell

Honeywell HC35WE5R3 Bruksanvisning

21 December 2024
Honeywell

Honeywell HD3C Bruksanvisning

23 September 2024
Honeywell

Honeywell Equip HCD5WIH Bruksanvisning

20 September 2024
Honeywell

Honeywell HDZ30A Bruksanvisning

2 September 2024
Honeywell

Honeywell Performance HD31H Bruksanvisning

1 September 2024
Honeywell

Honeywell HD50 Bruksanvisning

30 Augusti 2024
Honeywell

Honeywell Equip HDZ30 Bruksanvisning

29 Augusti 2024
Honeywell

Honeywell Performance HBW8PR2 Bruksanvisning

29 Augusti 2024
Honeywell

Honeywell HDZ36AEX Bruksanvisning

29 Augusti 2024

övervakningskamera Manualer

Nyaste övervakningskamera Manualer

Philips

Philips B120E Bruksanvisning

16 Januari 2025
Dahua Technology

Dahua Technology Pro IPC-HDPW5442G-Z Bruksanvisning

10 Januari 2025
Hikvision

Hikvision DS-2CE59U1T-AVPIT3ZF Bruksanvisning

8 Januari 2025
Hikvision

Hikvision IDS-2CD7526G0-IZHSY Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2163G0-I(S) Bruksanvisning

8 Januari 2025
Hikvision

Hikvision DS-2CD2H83G1-IZS Bruksanvisning

8 Januari 2025
Speco Technologies

Speco Technologies O5LB1 Bruksanvisning

8 Januari 2025
ZKTeco

ZKTeco AntarVis 2.0 Bruksanvisning

8 Januari 2025
Speco Technologies

Speco Technologies O2P30X Bruksanvisning

8 Januari 2025
TP Link

TP Link InSight S345ZI Bruksanvisning

8 Januari 2025